aboutsummaryrefslogtreecommitdiffstats
path: root/docs/G-Codes.md
Commit message (Expand)AuthorAgeFilesLines
* docs: Bltouch documentation (#1073)Wilfried Goesgens2019-01-051-0/+2
* respond: An extra for sending messages to the printer host. (#1053)Alec B. Plumb2019-01-021-0/+16
* bltouch: Add a BLTOUCH_DEBUG commandKevin O'Connor2018-12-031-0/+8
* servo: This patch create ability to enable/disable attached servo. (#880)Jiri Dobry2018-11-141-2/+2
* docs: Clarify M109/M190 in G-Code documentationKevin O'Connor2018-10-281-0/+4
* docs: Note the use of gcode_macro in G-Codes.mdKevin O'Connor2018-10-281-0/+6
* bed_mesh: Do not automatically run G28 on BED_MESH_CALIBRATE / BED_MESH_MAPKevin O'Connor2018-10-221-1/+1
* endstop_phase: Add support for an ENDSTOP_PHASE_CALIBRATE commandKevin O'Connor2018-10-161-0/+11
* docs: Fix typo in BED_MESH_PROFILE description in G-Codes.mdKevin O'Connor2018-10-041-1/+1
* bed_mesh: Add ability to save mesh state to persistent memoryArksine2018-10-021-0/+8
* probe: Support manual probing at runtimeKevin O'Connor2018-10-011-7/+13
* docs: Add Delta_Calibrate.md guide with "enhanced delta calibration"Kevin O'Connor2018-09-251-0/+2
* configfile: Add support for rewriting the printer config fileKevin O'Connor2018-09-251-0/+4
* heater: Add new TURN_OFF_HEATERS commandKevin O'Connor2018-09-181-0/+1
* docs: Add Mesh Bed Leveling to G-Codes.mdArksine2018-08-171-0/+19
* force_move: Provide defaults for SET_KINEMATIC_POSITION parametersKevin O'Connor2018-08-021-7/+9
* force_move: Add support for FORCE_MOVE commandKevin O'Connor2018-07-261-0/+22
* toolhead: Replace junction_deviation with square_corner_velocityKevin O'Connor2018-07-161-3/+3
* docs: Add M206 and M119 to G-Codes.mdKevin O'Connor2018-07-081-0/+8
* docs: Add display g-code commands to docs/G-Codes.mdKevin O'Connor2018-07-081-0/+7
* tmc2130: Add a DUMP_TMC helper commandKevin O'Connor2018-06-301-0/+7
* toolhead: Add support for the M204 commandKevin O'Connor2018-06-151-0/+1
* stepper: Add STEPPER_BUZZ commandKevin O'Connor2018-05-241-0/+3
* z_tilt: Add support for Z_TILT_ADJUSTKevin O'Connor2018-05-221-0/+8
* extruder: Fix SET_PRESSURE_ADVANCE so that it works with multiple extrudersKevin O'Connor2018-05-201-2/+3
* toolhead: Add a SET_VELOCITY_LIMIT commandKevin O'Connor2018-04-201-0/+4
* gcode: Add a SET_GCODE_OFFSET commandKevin O'Connor2018-04-201-1/+10
* extruder: Add SET_PRESSURE_ADVANCE command.Michael Barbour2018-04-031-0/+3
* docs: Update G-Codes.md with recent output_pin changesKevin O'Connor2018-03-281-3/+3
* pid_calibrate: Move PID calibration logic from heater.py to new fileKevin O'Connor2018-03-181-1/+7
* docs: Fix typo in M220 description in G-Codes.mdKevin O'Connor2018-03-181-1/+1
* gcode: Position returned by M114 should be relative to last G92Kevin O'Connor2018-03-151-0/+2
* docs: Add SET_DUAL_CARRIAGE command to G-Codes.mdKevin O'Connor2018-03-101-0/+8
* docs: Add Tx command to G-Codes.mdKevin O'Connor2018-03-081-0/+1
* docs: Add a G-Codes.md file with the list of available commandsKevin O'Connor2018-03-081-0/+114
generated by cgit v1.2.3-70-g09d2 (git 2.50.1) at 2025-09-02 12:04:45 +0000