aboutsummaryrefslogtreecommitdiffstats
path: root/config
Commit message (Expand)AuthorAgeFilesLines
* config: Add a generic-minitronics1.cfg example config fileKevin O'Connor2018-12-201-0/+80
* config: Add printer-micromake-d1-2016.cfg example config fileKevin O'Connor2018-12-181-0/+79
* bltouch: Document that bltouch "clones" may not work correctlyKevin O'Connor2018-12-181-7/+2
* bltouch: Add a config option to disable the bltouch sensor testKevin O'Connor2018-12-161-1/+7
* config: Fix CR-20 click pin polarityUri Shaked2018-12-151-1/+1
* config: Add printer config for the CR-20 by Creality3DUri Shaked2018-12-151-0/+81
* config: Update printer-creality-ender3-2018.cfg (#959)TronskiFPV2018-12-051-4/+4
* bltouch: Allow the pin_move_time to be configuredKevin O'Connor2018-12-041-0/+3
* config: Update bed_mesh in example-extras.cfgArksine2018-11-301-7/+17
* bltouch: Add initial support for a bltouch "extras" moduleKevin O'Connor2018-11-301-0/+18
* config: Rework sample-bltouch.cfg into sample-probe-as-z-endstop.cfgKevin O'Connor2018-11-302-56/+51
* config: Make the Anycubic delta configurations as similar as possibleruevs2018-11-252-15/+20
* mcp4451: Use bus.py helper code for i2cKevin O'Connor2018-11-241-1/+1
* uc1701: Add support for SSD1306 in i2c modeKevin O'Connor2018-11-231-4/+4
* uc1701: Add support for SSD1306 displaysKevin O'Connor2018-11-211-5/+10
* tmc2660: Use bus.py helper code for spiKevin O'Connor2018-11-212-17/+17
* servo: This patch create ability to enable/disable attached servo. (#880)Jiri Dobry2018-11-141-1/+3
* config: Use consistent advice on flashing the Melzi boardKevin O'Connor2018-11-137-53/+49
* config: sample-macros.cfg creation and M300ndupont-net2018-11-131-0/+36
* config: Add printer-velleman-k8200-2013.cfg example configKevin O'Connor2018-11-131-0/+95
* config: Add generic duet2 config and tests (#834)Florian Heilmann2018-10-311-0/+362
* Implement idle event support in the TMC2660 extraFlorian Heilmann2018-10-281-16/+13
* config: Add lcd encoder pins to generic-rumba.cfgKevin O'Connor2018-10-281-0/+4
* Add SX1509 extraFlorian Heilmann2018-10-271-0/+17
* config: Add encoder pins to printer-anycubic-kossel-plus-2017.cfgKevin O'Connor2018-10-251-0/+3
* extruder: Don't use max_extrude_cross_section in max_extrude_only defaultsKevin O'Connor2018-10-251-1/+1
* config: Update wording of extruder parameters in example.cfgKevin O'Connor2018-10-251-18/+17
* tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816)Florian Heilmann2018-10-241-1/+1
* config: Add display buttons to printer-creality-cr10s-2017.cfgKevin O'Connor2018-10-201-0/+2
* config: ADIMlab Add support for LCD knob and caselightJason Rahaim2018-10-191-3/+16
* endstop_phase: Add support for an ENDSTOP_PHASE_CALIBRATE commandKevin O'Connor2018-10-161-1/+2
* endstop_phase: Add support for detecting phase via TMC stepper driversKevin O'Connor2018-10-161-3/+5
* endstop_phase: Move endstop phase homing code to new "extras" moduleKevin O'Connor2018-10-162-24/+31
* config: Add ADIMLab 3d printer (#781)Jason R2018-10-161-0/+107
* cartesian: Use homing_speed for homing retract speedKevin O'Connor2018-10-091-6/+5
* servo: Adding support for startup value for servos (#676)Chris Whiteford2018-10-051-0/+9
* stepper: Adding support for a second_homing_speed parameter (#677)Chris Whiteford2018-10-041-0/+5
* docs: Spelling error corrected in bed mesh comment (#735)LazaroFilm2018-10-041-1/+1
* config: Minor indentation fix to comments in example-extras.cfgKevin O'Connor2018-10-011-14/+14
* config: Note probe activate/deactivate must not move the toolheadKevin O'Connor2018-10-011-4/+6
* probe: Infer position_endstop when using probe:z_virtual_offsetKevin O'Connor2018-10-012-5/+5
* config: The delta_calibrate bed radius uses nozzle coordinatesKevin O'Connor2018-10-011-8/+10
* bed_tilt: Remove special probe:z_virtual_endstop handlingKevin O'Connor2018-10-011-0/+3
* probe: Support manual probing at runtimeKevin O'Connor2018-10-012-19/+0
* avr: Use generic usb_cdc code for usb serial supportKevin O'Connor2018-09-301-1/+1
* config: Add encoder and click pins for CR-10 miniNikolai Ugelvik2018-09-301-0/+2
* config: Fix typo in gcode_macro default_parameter descriptionKevin O'Connor2018-09-301-1/+1
* gcode_macro: default parameter valuesJanar Sööt2018-09-301-0/+8
* config: Note gcode_macro string formatting in example-extras.cfgKevin O'Connor2018-09-261-2/+6
* config: Move some sections around in example-extras.cfgKevin O'Connor2018-09-261-49/+53
generated by cgit v1.2.3-70-g09d2 (git 2.50.1) at 2025-09-02 07:29:59 +0000