diff options
Diffstat (limited to 'config')
22 files changed, 68 insertions, 71 deletions
diff --git a/config/generic-bigtreetech-skr-e3-dip.cfg b/config/generic-bigtreetech-skr-e3-dip.cfg index 985b99fd..01655d4f 100644 --- a/config/generic-bigtreetech-skr-e3-dip.cfg +++ b/config/generic-bigtreetech-skr-e3-dip.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for the BIGTREETECH SKR E3 # DIP. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". Also, select "Enable extra -# low-level configuration options" and configure "GPIO pins to set at -# micro-controller startup" to "!PC13". +# STM32F103 with a "28KiB bootloader" and USB communication. Also, +# select "Enable extra low-level configuration options" and configure +# "GPIO pins to set at micro-controller startup" to "!PC13". # The "make flash" command does not work on the SKR E3 DIP. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg b/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg index eb7ef45d..463c90e3 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for the BIGTREETECH SKR mini # E3. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". Also, select "Enable extra -# low-level configuration options" and configure "GPIO pins to set at -# micro-controller startup" to "!PC13". +# STM32F103 with a "28KiB bootloader" and USB communication. Also, +# select "Enable extra low-level configuration options" and configure +# "GPIO pins to set at micro-controller startup" to "!PC13". # The "make flash" command does not work on the SKR mini E3. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg b/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg index 2e9a9c8a..a255224b 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for the BIGTREETECH SKR mini # E3 v1.2. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". Also, select "Enable extra -# low-level configuration options" and configure "GPIO pins to set at -# micro-controller startup" to "!PC13". +# STM32F103 with a "28KiB bootloader" and USB communication. Also, +# select "Enable extra low-level configuration options" and configure +# "GPIO pins to set at micro-controller startup" to "!PC13". # The "make flash" command does not work on the SKR mini E3. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg b/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg index 788cb150..6fb341b7 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for the BIGTREETECH SKR mini # E3 v2.0. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". Also, select "Enable extra -# low-level configuration options" and configure "GPIO pins to set at -# micro-controller startup" to "!PA14". +# STM32F103 with a "28KiB bootloader" and USB communication. Also, +# select "Enable extra low-level configuration options" and configure +# "GPIO pins to set at micro-controller startup" to "!PA14". # The "make flash" command does not work on the SKR mini E3. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-bigtreetech-skr-mini-mz.cfg b/config/generic-bigtreetech-skr-mini-mz.cfg index 2384e53b..c5268a0a 100644 --- a/config/generic-bigtreetech-skr-mini-mz.cfg +++ b/config/generic-bigtreetech-skr-mini-mz.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for the BIGTREETECH SKR mini # MZ v1.0. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". Also, select "Enable extra -# low-level configuration options" and configure "GPIO pins to set at -# micro-controller startup" to "!PA14". +# STM32F103 with a "28KiB bootloader" and USB communication. Also, +# select "Enable extra low-level configuration options" and configure +# "GPIO pins to set at micro-controller startup" to "!PA14". # The "make flash" command does not work on the SKR mini MZ. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-bigtreetech-skr-mini.cfg b/config/generic-bigtreetech-skr-mini.cfg index b085b013..f2cf080d 100644 --- a/config/generic-bigtreetech-skr-mini.cfg +++ b/config/generic-bigtreetech-skr-mini.cfg @@ -1,6 +1,6 @@ # This file contains common pin mappings for the BIGTREETECH SKR # MINI. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader". +# STM32F103 with a "28KiB bootloader" and USB communication. # The "make flash" command does not work on the SKR mini. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/generic-creality-v4.2.7.cfg b/config/generic-creality-v4.2.7.cfg index ef09fb41..41226828 100644 --- a/config/generic-creality-v4.2.7.cfg +++ b/config/generic-creality-v4.2.7.cfg @@ -1,11 +1,11 @@ # This file contains pin mappings for the Creality "v4.2.7" board. To # use this config, during "make menuconfig" select the STM32F103 with -# a "28KiB bootloader" and with "Use USB for communication" disabled. +# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication. # If you prefer a direct serial connection, in "make menuconfig" -# select "Enable extra low-level configuration options" and select the -# USART3 serial port, which is broken out on the 10 pin IDC cable used -# for the LCD module as follows: +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: # 3: Tx, 4: Rx, 9: GND, 10: VCC # Flash this firmware by copying "out/klipper.bin" to a SD card and diff --git a/config/generic-fysetc-cheetah-v1.1.cfg b/config/generic-fysetc-cheetah-v1.1.cfg index cae8f932..9650f37e 100644 --- a/config/generic-fysetc-cheetah-v1.1.cfg +++ b/config/generic-fysetc-cheetah-v1.1.cfg @@ -1,7 +1,7 @@ # This file contains common pin mappings for the Fysetc Cheetah v1.1 # board. To use this config, the firmware should be compiled for the -# STM32F103 with "No bootloader" and with "Use USB for communication" -# disabled. +# STM32F103 with "No bootloader" and serial (on USART1 PA10/PA9) +# communication. # The "make flash" command does not work on the Cheetah. Instead, # after running "make", run the following command to flash the board: diff --git a/config/generic-mks-robin-e3.cfg b/config/generic-mks-robin-e3.cfg index dac9d804..41eee77b 100644 --- a/config/generic-mks-robin-e3.cfg +++ b/config/generic-mks-robin-e3.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for MKS Robin E3 boards. To # use this config, the firmware should be compiled for the STM32F103. # When running "make menuconfig", enable "extra low-level -# configuration setup", select the 20KiB bootloader, disable "USB for -# communication", and select USART1 for the "Serial Port". +# configuration setup", select the 20KiB bootloader, and serial (on +# USART1 PA10/PA9) communication. # Note that the "make flash" command does not work with MKS Robin # boards. After running "make", run the following command: diff --git a/config/generic-mks-robin-nano-v1.cfg b/config/generic-mks-robin-nano-v1.cfg index 62e40119..bb096c81 100644 --- a/config/generic-mks-robin-nano-v1.cfg +++ b/config/generic-mks-robin-nano-v1.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for MKS Robin Nano (v1.2.004) # boards. To use this config, the firmware should be compiled for the # STM32F103. When running "make menuconfig", enable "extra low-level -# configuration setup", select the 28KiB bootloader, disable "USB for -# communication", and select USART3 for the "Serial Port". +# configuration setup", select the 28KiB bootloader, and serial (on +# USART3 PB11/PB10) communication. # Note that the "make flash" command does not work with MKS Robin # boards. After running "make", run the following command: diff --git a/config/generic-mks-robin-nano-v2.cfg b/config/generic-mks-robin-nano-v2.cfg index 80c707d7..e9da5115 100644 --- a/config/generic-mks-robin-nano-v2.cfg +++ b/config/generic-mks-robin-nano-v2.cfg @@ -1,8 +1,8 @@ # This file contains common pin mappings for MKS Robin Nano V2 # boards. To use this config, the firmware should be compiled for the # STM32F103. When running "make menuconfig", enable "extra low-level -# configuration setup", select the 28KiB bootloader, disable "USB for -# communication", and select USART3 for the "Serial Port". +# configuration setup", select the 28KiB bootloader, and serial (on +# USART3 PB11/PB10) communication. # Note that the "make flash" command does not work with MKS Robin # boards. After running "make", run the following command: diff --git a/config/printer-alfawise-u30-2018.cfg b/config/printer-alfawise-u30-2018.cfg index 0cdaae1d..d8b375e1 100644 --- a/config/printer-alfawise-u30-2018.cfg +++ b/config/printer-alfawise-u30-2018.cfg @@ -1,9 +1,9 @@ # This file contains common pin mappings for the Alfawise U30 printer. # To use this config, the firmware should be compiled for the # STM32F103. When running "make menuconfig", enable "extra low-level -# configuration setup", select the 64KiB bootloader, disable "USB for -# communication", and set "GPIO pins to set at micro-controller -# startup" to "!PC4,!PD12". +# configuration setup", select the 64KiB bootloader, serial (on USART1 +# PA10/PA9) communication, and set "GPIO pins to set at +# micro-controller startup" to "!PC4,!PD12". # The "make flash" command does not work on the Alfawise U30. Instead, # after running "make", copy the generated "out/klipper.bin" file to a diff --git a/config/printer-creality-cr6se-2020.cfg b/config/printer-creality-cr6se-2020.cfg index 10e5476f..11d827ea 100644 --- a/config/printer-creality-cr6se-2020.cfg +++ b/config/printer-creality-cr6se-2020.cfg @@ -1,7 +1,7 @@ # This file contains pin mappings for the stock 2020 Creality CR6-SE. -# To use this config, during "make menuconfig" select the -# STM32F103 with a "28KiB bootloader" and with "Use USB for -# communication" disabled. +# To use this config, during "make menuconfig" select the STM32F103 +# with a "28KiB bootloader" and serial (on USART1 PA10/PA9) +# communication. # Flash this firmware by copying "out/klipper.bin" to a SD card and # turning on the printer with the card inserted. The firmware diff --git a/config/printer-creality-ender3-v2-2020.cfg b/config/printer-creality-ender3-v2-2020.cfg index 7efe5fe2..a0ca79cb 100644 --- a/config/printer-creality-ender3-v2-2020.cfg +++ b/config/printer-creality-ender3-v2-2020.cfg @@ -1,12 +1,12 @@ # This file contains pin mappings for the stock 2020 Creality Ender 3 # V2. To use this config, during "make menuconfig" select the -# STM32F103 with a "28KiB bootloader" and with "Use USB for -# communication" disabled. +# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) +# communication. # If you prefer a direct serial connection, in "make menuconfig" -# select "Enable extra low-level configuration options" and select the -# USART3 serial port, which is broken out on the 10 pin IDC cable used -# for the LCD module as follows: +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: # 3: Tx, 4: Rx, 9: GND, 10: VCC # Flash this firmware by copying "out/klipper.bin" to a SD card and diff --git a/config/printer-creality-ender3max-2021.cfg b/config/printer-creality-ender3max-2021.cfg index fa7559d7..dd975e02 100644 --- a/config/printer-creality-ender3max-2021.cfg +++ b/config/printer-creality-ender3max-2021.cfg @@ -1,7 +1,7 @@ # This file contains pin mappings for the stock 2020 Creality Ender 3 # MAX. To use this config, during "make menuconfig" select the -# STM32F103 with a "28KiB bootloader" and with "Use USB for -# communication" disabled. +# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) +# communication. # Because this printer has factory wiring, mounts, and firmware for # a BLTouch, but does not ship with one at this time, default values @@ -10,9 +10,9 @@ # customize the offsets, particularly z-offset, for their specific unit. # If you prefer a direct serial connection, in "make menuconfig" -# select "Enable extra low-level configuration options" and select the -# USART3 serial port, which is broken out on the 10 pin IDC cable used -# for the LCD module as follows: +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: # 3: Tx, 4: Rx, 9: GND, 10: VCC # Flash this firmware by copying "out/klipper.bin" to a SD card and diff --git a/config/printer-creality-ender3pro-2020.cfg b/config/printer-creality-ender3pro-2020.cfg index b3a35528..04b5f004 100644 --- a/config/printer-creality-ender3pro-2020.cfg +++ b/config/printer-creality-ender3pro-2020.cfg @@ -1,12 +1,12 @@ # This file contains pin mappings for the stock 2020 Creality Ender 3 # Pro with the 32-bit Creality 4.2.2 board. To use this config, during # "make menuconfig" select the STM32F103 with a "28KiB bootloader" and -# with "Use USB for communication" disabled. +# serial (on USART1 PA10/PA9) communication. # If you prefer a direct serial connection, in "make menuconfig" -# select "Enable extra low-level configuration options" and select the -# USART3 serial port, which is broken out on the 10 pin IDC cable used -# for the LCD module as follows: +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: # 3: Tx, 4: Rx, 9: GND, 10: VCC # Flash this firmware by copying "out/klipper.bin" to a SD card and diff --git a/config/printer-creality-ender6-2020.cfg b/config/printer-creality-ender6-2020.cfg index 00875018..a5791a84 100644 --- a/config/printer-creality-ender6-2020.cfg +++ b/config/printer-creality-ender6-2020.cfg @@ -1,7 +1,7 @@ # This file contains pin mappings for the stock 2020 Creality Ender 6. -# To use this config, during "make menuconfig" select the -# STM32F103 with a "28KiB bootloader" and with "Use USB for -# communication" disabled. +# To use this config, during "make menuconfig" select the STM32F103 +# with a "28KiB bootloader" and serial (on USART1 PA10/PA9) +# communication. # Because this printer has factory wiring, mounts, and firmware for # a BLTouch, but does not ship with one at this time, default values @@ -10,9 +10,9 @@ # customize the offsets, particularly z-offset, for their specific unit. # If you prefer a direct serial connection, in "make menuconfig" -# select "Enable extra low-level configuration options" and select the -# USART3 serial port, which is broken out on the 10 pin IDC cable used -# for the LCD module as follows: +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: # 3: Tx, 4: Rx, 9: GND, 10: VCC # Flash this firmware by copying "out/klipper.bin" to a SD card and diff --git a/config/printer-flsun-q5-2020.cfg b/config/printer-flsun-q5-2020.cfg index 477309b7..59a44dca 100644 --- a/config/printer-flsun-q5-2020.cfg +++ b/config/printer-flsun-q5-2020.cfg @@ -3,8 +3,8 @@ # To use this config, the firmware should be compiled for the # STM32F103. When running "make menuconfig", enable "extra low-level -# configuration setup", select the 28KiB bootloader, disable "USB for -# communication", and select USART3 for the "Serial Port". +# configuration setup", select the 28KiB bootloader, and serial (on +# USART3 PB11/PB10) communication. # Note that the "make flash" command does not work with MKS Robin # boards. After running "make", run the following command: diff --git a/config/printer-monoprice-mini-delta-2017.cfg b/config/printer-monoprice-mini-delta-2017.cfg index 0115ba77..b8cfc5e5 100644 --- a/config/printer-monoprice-mini-delta-2017.cfg +++ b/config/printer-monoprice-mini-delta-2017.cfg @@ -1,7 +1,6 @@ # This file contains common pin mappings for the 2017 Monoprice # Mini Delta. To use this config, the firmware should be compiled for the -# STM32F070 microcontroller with an 8MHz crystal and USB for communication -# (instead of serial). +# STM32F070 microcontroller with an 8MHz crystal and USB for communication. # # IMPORTANT: Use of Kipper with a Monoprice Mini Delta requires a power supply # with a _minimum_ 120 W (i.e. 10 A) capacity! The stock power supply will not diff --git a/config/printer-monoprice-select-mini-v2-2018.cfg b/config/printer-monoprice-select-mini-v2-2018.cfg index dd4ded29..3bc86c75 100644 --- a/config/printer-monoprice-select-mini-v2-2018.cfg +++ b/config/printer-monoprice-select-mini-v2-2018.cfg @@ -1,7 +1,6 @@ # This file contains common pin mappings for the 2019 Monoprice # Select Mini v2. To use this config, the firmware should be compiled for the -# STM32F070 microcontroller with an 8MHz crystal and USB for communication -# (instead of serial). +# STM32F070 microcontroller with an 8MHz crystal and USB for communication. # # Use the following settings in make menuconfig: # diff --git a/config/printer-tronxy-x5sa-v6-2019.cfg b/config/printer-tronxy-x5sa-v6-2019.cfg index 96639a99..069f60d6 100644 --- a/config/printer-tronxy-x5sa-v6-2019.cfg +++ b/config/printer-tronxy-x5sa-v6-2019.cfg @@ -1,15 +1,15 @@ -# This is a Klipper configuration for TronXY X5SA, with -# CXY-V6 motherboard. - +# This is a Klipper configuration for TronXY X5SA, with CXY-V6 +# motherboard. # === FLASHING WITH STOCK BOOTLOADER === # You should make firmware for STM32F103 with bootloader offset -# at 0x8008800 (Chitu v6 Bootloader). Uncheck USB, and leave default -# serial settings. -# -# Use "./scripts/update_chitu.py ./out/klipper.bin ./out/update.cbd" after make to generate update.cbd. -# Put `update.cbd` onto SD card, and reboot the printer. -# It will be automatically installed, and you will be able to update it this way. +# at 0x8008800 (Chitu v6 Bootloader) and serial (on USART1 PA10/PA9) +# communication. + +# Use "./scripts/update_chitu.py ./out/klipper.bin ./out/update.cbd" +# after make to generate update.cbd. Put `update.cbd` onto SD card, +# and reboot the printer. It will be automatically installed, and you +# will be able to update it this way. [mcu] serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 diff --git a/config/printer-twotrees-sapphire-plus-2020.cfg b/config/printer-twotrees-sapphire-plus-2020.cfg index 5212610d..9193ab56 100644 --- a/config/printer-twotrees-sapphire-plus-2020.cfg +++ b/config/printer-twotrees-sapphire-plus-2020.cfg @@ -5,8 +5,7 @@ # When running "make menuconfig" you have to: # - enable "extra low-level configuration setup", # - select the 28KiB bootloader, -# - disable "USB for communication" -# - select USART3 for the "Serial Port" +# - select serial (on USART3 PB11/PB10) communication # - set "GPIO pins to set at micro-controller startup" to "!PC6,!PD13" # Note that the "make flash" command does not work with the Sapphire |