blob: 782c30ca1b4da3a58021f6f1b5296327741a3cde (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
|
// THIS HEADER FILE IS AUTOMATICALLY GENERATED -- DO NOT EDIT
/**
* Copyright (c) 2024 Raspberry Pi Ltd.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
// =============================================================================
// Register block : XOSC
// Version : 1
// Bus type : apb
// Description : Controls the crystal oscillator
// =============================================================================
#ifndef _HARDWARE_REGS_XOSC_H
#define _HARDWARE_REGS_XOSC_H
// =============================================================================
// Register : XOSC_CTRL
// Description : Crystal Oscillator Control
#define XOSC_CTRL_OFFSET _u(0x00000000)
#define XOSC_CTRL_BITS _u(0x00ffffff)
#define XOSC_CTRL_RESET _u(0x00000000)
// -----------------------------------------------------------------------------
// Field : XOSC_CTRL_ENABLE
// Description : On power-up this field is initialised to DISABLE and the chip
// runs from the ROSC.
// If the chip has subsequently been programmed to run from the
// XOSC then setting this field to DISABLE may lock-up the chip.
// If this is a concern then run the clk_ref from the ROSC and
// enable the clk_sys RESUS feature.
// The 12-bit code is intended to give some protection against
// accidental writes. An invalid setting will retain the previous
// value. The actual value being used can be read from
// STATUS_ENABLED
// 0xd1e -> DISABLE
// 0xfab -> ENABLE
#define XOSC_CTRL_ENABLE_RESET "-"
#define XOSC_CTRL_ENABLE_BITS _u(0x00fff000)
#define XOSC_CTRL_ENABLE_MSB _u(23)
#define XOSC_CTRL_ENABLE_LSB _u(12)
#define XOSC_CTRL_ENABLE_ACCESS "RW"
#define XOSC_CTRL_ENABLE_VALUE_DISABLE _u(0xd1e)
#define XOSC_CTRL_ENABLE_VALUE_ENABLE _u(0xfab)
// -----------------------------------------------------------------------------
// Field : XOSC_CTRL_FREQ_RANGE
// Description : The 12-bit code is intended to give some protection against
// accidental writes. An invalid setting will retain the previous
// value. The actual value being used can be read from
// STATUS_FREQ_RANGE
// 0xaa0 -> 1_15MHZ
// 0xaa1 -> 10_30MHZ
// 0xaa2 -> 25_60MHZ
// 0xaa3 -> 40_100MHZ
#define XOSC_CTRL_FREQ_RANGE_RESET "-"
#define XOSC_CTRL_FREQ_RANGE_BITS _u(0x00000fff)
#define XOSC_CTRL_FREQ_RANGE_MSB _u(11)
#define XOSC_CTRL_FREQ_RANGE_LSB _u(0)
#define XOSC_CTRL_FREQ_RANGE_ACCESS "RW"
#define XOSC_CTRL_FREQ_RANGE_VALUE_1_15MHZ _u(0xaa0)
#define XOSC_CTRL_FREQ_RANGE_VALUE_10_30MHZ _u(0xaa1)
#define XOSC_CTRL_FREQ_RANGE_VALUE_25_60MHZ _u(0xaa2)
#define XOSC_CTRL_FREQ_RANGE_VALUE_40_100MHZ _u(0xaa3)
// =============================================================================
// Register : XOSC_STATUS
// Description : Crystal Oscillator Status
#define XOSC_STATUS_OFFSET _u(0x00000004)
#define XOSC_STATUS_BITS _u(0x81001003)
#define XOSC_STATUS_RESET _u(0x00000000)
// -----------------------------------------------------------------------------
// Field : XOSC_STATUS_STABLE
// Description : Oscillator is running and stable
#define XOSC_STATUS_STABLE_RESET _u(0x0)
#define XOSC_STATUS_STABLE_BITS _u(0x80000000)
#define XOSC_STATUS_STABLE_MSB _u(31)
#define XOSC_STATUS_STABLE_LSB _u(31)
#define XOSC_STATUS_STABLE_ACCESS "RO"
// -----------------------------------------------------------------------------
// Field : XOSC_STATUS_BADWRITE
// Description : An invalid value has been written to CTRL_ENABLE or
// CTRL_FREQ_RANGE or DORMANT
#define XOSC_STATUS_BADWRITE_RESET _u(0x0)
#define XOSC_STATUS_BADWRITE_BITS _u(0x01000000)
#define XOSC_STATUS_BADWRITE_MSB _u(24)
#define XOSC_STATUS_BADWRITE_LSB _u(24)
#define XOSC_STATUS_BADWRITE_ACCESS "WC"
// -----------------------------------------------------------------------------
// Field : XOSC_STATUS_ENABLED
// Description : Oscillator is enabled but not necessarily running and stable,
// resets to 0
#define XOSC_STATUS_ENABLED_RESET "-"
#define XOSC_STATUS_ENABLED_BITS _u(0x00001000)
#define XOSC_STATUS_ENABLED_MSB _u(12)
#define XOSC_STATUS_ENABLED_LSB _u(12)
#define XOSC_STATUS_ENABLED_ACCESS "RO"
// -----------------------------------------------------------------------------
// Field : XOSC_STATUS_FREQ_RANGE
// Description : The current frequency range setting
// 0x0 -> 1_15MHZ
// 0x1 -> 10_30MHZ
// 0x2 -> 25_60MHZ
// 0x3 -> 40_100MHZ
#define XOSC_STATUS_FREQ_RANGE_RESET "-"
#define XOSC_STATUS_FREQ_RANGE_BITS _u(0x00000003)
#define XOSC_STATUS_FREQ_RANGE_MSB _u(1)
#define XOSC_STATUS_FREQ_RANGE_LSB _u(0)
#define XOSC_STATUS_FREQ_RANGE_ACCESS "RO"
#define XOSC_STATUS_FREQ_RANGE_VALUE_1_15MHZ _u(0x0)
#define XOSC_STATUS_FREQ_RANGE_VALUE_10_30MHZ _u(0x1)
#define XOSC_STATUS_FREQ_RANGE_VALUE_25_60MHZ _u(0x2)
#define XOSC_STATUS_FREQ_RANGE_VALUE_40_100MHZ _u(0x3)
// =============================================================================
// Register : XOSC_DORMANT
// Description : Crystal Oscillator pause control
// This is used to save power by pausing the XOSC
// On power-up this field is initialised to WAKE
// An invalid write will also select WAKE
// Warning: stop the PLLs before selecting dormant mode
// Warning: setup the irq before selecting dormant mode
// 0x636f6d61 -> dormant
// 0x77616b65 -> WAKE
#define XOSC_DORMANT_OFFSET _u(0x00000008)
#define XOSC_DORMANT_BITS _u(0xffffffff)
#define XOSC_DORMANT_RESET "-"
#define XOSC_DORMANT_MSB _u(31)
#define XOSC_DORMANT_LSB _u(0)
#define XOSC_DORMANT_ACCESS "RW"
#define XOSC_DORMANT_VALUE_DORMANT _u(0x636f6d61)
#define XOSC_DORMANT_VALUE_WAKE _u(0x77616b65)
// =============================================================================
// Register : XOSC_STARTUP
// Description : Controls the startup delay
#define XOSC_STARTUP_OFFSET _u(0x0000000c)
#define XOSC_STARTUP_BITS _u(0x00103fff)
#define XOSC_STARTUP_RESET _u(0x00000000)
// -----------------------------------------------------------------------------
// Field : XOSC_STARTUP_X4
// Description : Multiplies the startup_delay by 4, just in case. The reset
// value is controlled by a mask-programmable tiecell and is
// provided in case we are booting from XOSC and the default
// startup delay is insufficient. The reset value is 0x0.
#define XOSC_STARTUP_X4_RESET "-"
#define XOSC_STARTUP_X4_BITS _u(0x00100000)
#define XOSC_STARTUP_X4_MSB _u(20)
#define XOSC_STARTUP_X4_LSB _u(20)
#define XOSC_STARTUP_X4_ACCESS "RW"
// -----------------------------------------------------------------------------
// Field : XOSC_STARTUP_DELAY
// Description : in multiples of 256*xtal_period. The reset value of 0xc4
// corresponds to approx 50 000 cycles.
#define XOSC_STARTUP_DELAY_RESET "-"
#define XOSC_STARTUP_DELAY_BITS _u(0x00003fff)
#define XOSC_STARTUP_DELAY_MSB _u(13)
#define XOSC_STARTUP_DELAY_LSB _u(0)
#define XOSC_STARTUP_DELAY_ACCESS "RW"
// =============================================================================
// Register : XOSC_COUNT
// Description : A down counter running at the xosc frequency which counts to
// zero and stops.
// Can be used for short software pauses when setting up time
// sensitive hardware.
// To start the counter, write a non-zero value. Reads will return
// 1 while the count is running and 0 when it has finished.
// Minimum count value is 4. Count values <4 will be treated as
// count value =4.
// Note that synchronisation to the register clock domain costs 2
// register clock cycles and the counter cannot compensate for
// that.
#define XOSC_COUNT_OFFSET _u(0x00000010)
#define XOSC_COUNT_BITS _u(0x0000ffff)
#define XOSC_COUNT_RESET _u(0x00000000)
#define XOSC_COUNT_MSB _u(15)
#define XOSC_COUNT_LSB _u(0)
#define XOSC_COUNT_ACCESS "RW"
// =============================================================================
#endif // _HARDWARE_REGS_XOSC_H
|
