diff options
Diffstat (limited to 'lib/pico-sdk/rp2350/hardware/regs/xosc.h')
| -rw-r--r-- | lib/pico-sdk/rp2350/hardware/regs/xosc.h | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/lib/pico-sdk/rp2350/hardware/regs/xosc.h b/lib/pico-sdk/rp2350/hardware/regs/xosc.h new file mode 100644 index 00000000..782c30ca --- /dev/null +++ b/lib/pico-sdk/rp2350/hardware/regs/xosc.h @@ -0,0 +1,175 @@ +// THIS HEADER FILE IS AUTOMATICALLY GENERATED -- DO NOT EDIT + +/** + * Copyright (c) 2024 Raspberry Pi Ltd. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +// ============================================================================= +// Register block : XOSC +// Version : 1 +// Bus type : apb +// Description : Controls the crystal oscillator +// ============================================================================= +#ifndef _HARDWARE_REGS_XOSC_H +#define _HARDWARE_REGS_XOSC_H +// ============================================================================= +// Register : XOSC_CTRL +// Description : Crystal Oscillator Control +#define XOSC_CTRL_OFFSET _u(0x00000000) +#define XOSC_CTRL_BITS _u(0x00ffffff) +#define XOSC_CTRL_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : XOSC_CTRL_ENABLE +// Description : On power-up this field is initialised to DISABLE and the chip +// runs from the ROSC. +// If the chip has subsequently been programmed to run from the +// XOSC then setting this field to DISABLE may lock-up the chip. +// If this is a concern then run the clk_ref from the ROSC and +// enable the clk_sys RESUS feature. +// The 12-bit code is intended to give some protection against +// accidental writes. An invalid setting will retain the previous +// value. The actual value being used can be read from +// STATUS_ENABLED +// 0xd1e -> DISABLE +// 0xfab -> ENABLE +#define XOSC_CTRL_ENABLE_RESET "-" +#define XOSC_CTRL_ENABLE_BITS _u(0x00fff000) +#define XOSC_CTRL_ENABLE_MSB _u(23) +#define XOSC_CTRL_ENABLE_LSB _u(12) +#define XOSC_CTRL_ENABLE_ACCESS "RW" +#define XOSC_CTRL_ENABLE_VALUE_DISABLE _u(0xd1e) +#define XOSC_CTRL_ENABLE_VALUE_ENABLE _u(0xfab) +// ----------------------------------------------------------------------------- +// Field : XOSC_CTRL_FREQ_RANGE +// Description : The 12-bit code is intended to give some protection against +// accidental writes. An invalid setting will retain the previous +// value. The actual value being used can be read from +// STATUS_FREQ_RANGE +// 0xaa0 -> 1_15MHZ +// 0xaa1 -> 10_30MHZ +// 0xaa2 -> 25_60MHZ +// 0xaa3 -> 40_100MHZ +#define XOSC_CTRL_FREQ_RANGE_RESET "-" +#define XOSC_CTRL_FREQ_RANGE_BITS _u(0x00000fff) +#define XOSC_CTRL_FREQ_RANGE_MSB _u(11) +#define XOSC_CTRL_FREQ_RANGE_LSB _u(0) +#define XOSC_CTRL_FREQ_RANGE_ACCESS "RW" +#define XOSC_CTRL_FREQ_RANGE_VALUE_1_15MHZ _u(0xaa0) +#define XOSC_CTRL_FREQ_RANGE_VALUE_10_30MHZ _u(0xaa1) +#define XOSC_CTRL_FREQ_RANGE_VALUE_25_60MHZ _u(0xaa2) +#define XOSC_CTRL_FREQ_RANGE_VALUE_40_100MHZ _u(0xaa3) +// ============================================================================= +// Register : XOSC_STATUS +// Description : Crystal Oscillator Status +#define XOSC_STATUS_OFFSET _u(0x00000004) +#define XOSC_STATUS_BITS _u(0x81001003) +#define XOSC_STATUS_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : XOSC_STATUS_STABLE +// Description : Oscillator is running and stable +#define XOSC_STATUS_STABLE_RESET _u(0x0) +#define XOSC_STATUS_STABLE_BITS _u(0x80000000) +#define XOSC_STATUS_STABLE_MSB _u(31) +#define XOSC_STATUS_STABLE_LSB _u(31) +#define XOSC_STATUS_STABLE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : XOSC_STATUS_BADWRITE +// Description : An invalid value has been written to CTRL_ENABLE or +// CTRL_FREQ_RANGE or DORMANT +#define XOSC_STATUS_BADWRITE_RESET _u(0x0) +#define XOSC_STATUS_BADWRITE_BITS _u(0x01000000) +#define XOSC_STATUS_BADWRITE_MSB _u(24) +#define XOSC_STATUS_BADWRITE_LSB _u(24) +#define XOSC_STATUS_BADWRITE_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : XOSC_STATUS_ENABLED +// Description : Oscillator is enabled but not necessarily running and stable, +// resets to 0 +#define XOSC_STATUS_ENABLED_RESET "-" +#define XOSC_STATUS_ENABLED_BITS _u(0x00001000) +#define XOSC_STATUS_ENABLED_MSB _u(12) +#define XOSC_STATUS_ENABLED_LSB _u(12) +#define XOSC_STATUS_ENABLED_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : XOSC_STATUS_FREQ_RANGE +// Description : The current frequency range setting +// 0x0 -> 1_15MHZ +// 0x1 -> 10_30MHZ +// 0x2 -> 25_60MHZ +// 0x3 -> 40_100MHZ +#define XOSC_STATUS_FREQ_RANGE_RESET "-" +#define XOSC_STATUS_FREQ_RANGE_BITS _u(0x00000003) +#define XOSC_STATUS_FREQ_RANGE_MSB _u(1) +#define XOSC_STATUS_FREQ_RANGE_LSB _u(0) +#define XOSC_STATUS_FREQ_RANGE_ACCESS "RO" +#define XOSC_STATUS_FREQ_RANGE_VALUE_1_15MHZ _u(0x0) +#define XOSC_STATUS_FREQ_RANGE_VALUE_10_30MHZ _u(0x1) +#define XOSC_STATUS_FREQ_RANGE_VALUE_25_60MHZ _u(0x2) +#define XOSC_STATUS_FREQ_RANGE_VALUE_40_100MHZ _u(0x3) +// ============================================================================= +// Register : XOSC_DORMANT +// Description : Crystal Oscillator pause control +// This is used to save power by pausing the XOSC +// On power-up this field is initialised to WAKE +// An invalid write will also select WAKE +// Warning: stop the PLLs before selecting dormant mode +// Warning: setup the irq before selecting dormant mode +// 0x636f6d61 -> dormant +// 0x77616b65 -> WAKE +#define XOSC_DORMANT_OFFSET _u(0x00000008) +#define XOSC_DORMANT_BITS _u(0xffffffff) +#define XOSC_DORMANT_RESET "-" +#define XOSC_DORMANT_MSB _u(31) +#define XOSC_DORMANT_LSB _u(0) +#define XOSC_DORMANT_ACCESS "RW" +#define XOSC_DORMANT_VALUE_DORMANT _u(0x636f6d61) +#define XOSC_DORMANT_VALUE_WAKE _u(0x77616b65) +// ============================================================================= +// Register : XOSC_STARTUP +// Description : Controls the startup delay +#define XOSC_STARTUP_OFFSET _u(0x0000000c) +#define XOSC_STARTUP_BITS _u(0x00103fff) +#define XOSC_STARTUP_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : XOSC_STARTUP_X4 +// Description : Multiplies the startup_delay by 4, just in case. The reset +// value is controlled by a mask-programmable tiecell and is +// provided in case we are booting from XOSC and the default +// startup delay is insufficient. The reset value is 0x0. +#define XOSC_STARTUP_X4_RESET "-" +#define XOSC_STARTUP_X4_BITS _u(0x00100000) +#define XOSC_STARTUP_X4_MSB _u(20) +#define XOSC_STARTUP_X4_LSB _u(20) +#define XOSC_STARTUP_X4_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : XOSC_STARTUP_DELAY +// Description : in multiples of 256*xtal_period. The reset value of 0xc4 +// corresponds to approx 50 000 cycles. +#define XOSC_STARTUP_DELAY_RESET "-" +#define XOSC_STARTUP_DELAY_BITS _u(0x00003fff) +#define XOSC_STARTUP_DELAY_MSB _u(13) +#define XOSC_STARTUP_DELAY_LSB _u(0) +#define XOSC_STARTUP_DELAY_ACCESS "RW" +// ============================================================================= +// Register : XOSC_COUNT +// Description : A down counter running at the xosc frequency which counts to +// zero and stops. +// Can be used for short software pauses when setting up time +// sensitive hardware. +// To start the counter, write a non-zero value. Reads will return +// 1 while the count is running and 0 when it has finished. +// Minimum count value is 4. Count values <4 will be treated as +// count value =4. +// Note that synchronisation to the register clock domain costs 2 +// register clock cycles and the counter cannot compensate for +// that. +#define XOSC_COUNT_OFFSET _u(0x00000010) +#define XOSC_COUNT_BITS _u(0x0000ffff) +#define XOSC_COUNT_RESET _u(0x00000000) +#define XOSC_COUNT_MSB _u(15) +#define XOSC_COUNT_LSB _u(0) +#define XOSC_COUNT_ACCESS "RW" +// ============================================================================= +#endif // _HARDWARE_REGS_XOSC_H + |