aboutsummaryrefslogtreecommitdiffstats
path: root/config/example-extras.cfg
Commit message (Collapse)AuthorAgeFilesLines
...
* config: Minor wording change to gcode_macro rename_existing descriptionKevin O'Connor2020-02-131-5/+5
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* gcode_macro: Support overriding of builtin g-code commandsKevin O'Connor2020-02-121-0/+7
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* homing_heaters: Turn off heaters during homing/probing (#2486)FanDjango2020-02-121-0/+12
| | | Signed-off-by: Mike Stiemke <fandjango@gmx.de>
* probe: Add support for configuring lift_speedKevin O'Connor2020-01-311-0/+4
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: add BME280 documentationArksine2020-01-131-0/+21
| | | | Signed-off-by: Eric Callahan <arksine.code@gmail.com>
* docs: Update documentation to reflect bed_mesh changesArksine2020-01-091-16/+22
| | | | | | Also add new bed_mesh.md documentation. Signed-off-by: Eric Callahan <arksine.code@gmail.com>
* gcode: Fix detection of some "extended" g-code commandsKevin O'Connor2020-01-071-10/+6
| | | | | | | Fix typo that resulted in _get_extended_params() being called for all commands. Allow "extended" g-code commands to contain numbers. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* extruder_stepper: Initial support for synchronized extruder steppersSimo Apell2020-01-061-0/+14
| | | | | Signed-off-by: Simo Apell <simo.apell@live.fi> Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* docs: Updates for gcode_macro naming (#2317)David Smith2020-01-061-4/+10
| | | | | Add note about numbers in macro names. Add note about variable name case restriction. Add set variable example. Signed-off-by: David O Smith <davidosmith@gmail.com>
* display: Revert "display: Add ST7567 display support (#1540)"Kevin O'Connor2019-12-181-8/+3
| | | | | | | | | This reverts commit 1b92af60784ea811a7ca04dfbce75224874cf84a. The standard "uc1701" lcd_type can now be used in place of the custom "st7567" lcd_type. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Minor wording change in example-extras.cfgKevin O'Connor2019-12-161-1/+1
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Update example-extras.cfg - extruder.activate_gcode was removedKevin O'Connor2019-12-161-4/+3
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* gcode: Remove builtin T0/T1/T2/... command supportKevin O'Connor2019-12-101-13/+0
| | | | | | | | The builtin Tn command is not sufficiently flexible to control some multi-extruder printers. Remove the command and encourage users to define individual gcode_macros for each Tn instance. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Add example for including a parameter in a macro call (#2251)David Smith2019-12-101-3/+5
| | | | | Add description to default_parameter of g-code macro description of method to call macro with a non-default value. Signed-off-by: David Smith <davidosmith@gmail.com>
* uc1701: Add support for rst_pinKevin O'Connor2019-12-021-2/+4
| | | | | | | Add support for an optional uc1701 rst_pin. Use the same reset pin code handling with the SSD1306 code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Minor comment changes to example-extras.cfgKevin O'Connor2019-11-281-13/+13
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* uc1701: add config option for sh1106 type with up to 132 columns.Matt Baker2019-11-261-1/+1
| | | | Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
* tmc: Remove virtual_enable support and replace with automatic supportKevin O'Connor2019-11-121-20/+5
| | | | | | | Automatically detect if the stepper has a dedicated enable line. If it does not, then automatically enable virtual enable support. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* buttons: Remove MCU_ADC_buttons debug capabilityKevin O'Connor2019-11-071-4/+0
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Only document thermistors in example.cfgKevin O'Connor2019-10-271-79/+74
| | | | | | | | | Move the common temperature amplifier config descriptions to example-extras.cfg. Also, minor changes to wording of some example-extra.cfg sections. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* adc_temperature: add support for AD849x thermocouple amplifiers (#1994)Geoff Shannon2019-10-101-0/+18
| | | Signed-off-by: Geoff Shannon <geoffpshannon@gmail.com>
* safe_z_home: Fix unintended change in default behaviorMaster922019-10-031-2/+2
| | | | | | PR #1970 introduced a new parameter, controlling the default behavior of the safe_z_home-module. To avoid unexpected changes, the default of the move_to_previous is now defaulted to False. Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
* safe_z_home: Hop only if necessary and add option to move xy backMaster922019-09-181-1/+8
| | | | | | | | | | | | | | | Once a hop is performed, it will only be re-issued if the z-axis has been moved in the meantime. Usually it is only moved by a z-homing so doing so will cause safe_z_home to do the hop on the next homing action. When z-axis is homed, x and y positions are known. When setting this boolean option, these are set back to their last positions. Whenever a hop is specified it is re-issued after the Z axis has been homed. This is especially necessary when a pressure-based probe is used. Also, the module decides if a hop is necessary, based on either a known Z position or a flag that is set whenever the motors are disabled. Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
* config: Fix grammar and typos for the new arc config (#1968)Piotr Usewicz2019-09-181-4/+4
| | | Signed-off-by: Piotr Usewicz <piotr@layer22.com>
* config: Move sections around in example-extras.cfgKevin O'Connor2019-09-131-747/+775
| | | | | | | Move the sections around in example-extras.cfg to try and group like functionality together. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* gcode_arcs: Add support for G2/G3 commandsAleksej Vasiljkovic2019-09-131-0/+10
| | | | | | | | R Still missing, also might be somewhat dirty since code is converted into G1 commands. Signed-off-by: Aleksej Vasiljkovic <achmed21@gmail.com> Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Note adc_voltage and pullup_resistance in adc_temperature moduleKevin O'Connor2019-09-111-3/+7
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* filament_switch_sensor: Add a delay between dispatch of pause and execution ↵Arksine2019-09-081-0/+5
| | | | | | of pause gcode Signed-off-by: Eric Callahan <arksine.code@gmail.com>
* board_pins: Add a new "extras" module to support per-board pin aliasesKevin O'Connor2019-08-191-0/+13
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* tmc2209: Add support for sensorless homingKevin O'Connor2019-08-191-0/+7
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* uc1701: Add support for a reset line on SSD1306 displaysKevin O'Connor2019-08-171-0/+4
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Note that samples_tolerance can be used in the bltouch configKevin O'Connor2019-08-171-0/+2
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* neopixel: Add support for WS2811 RGB pixel color orderKevin O'Connor2019-08-091-0/+3
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* extra: Add Safe Z home extraFlorian Heilmann2019-08-091-0/+19
| | | | Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
* dotstar: Initial support for "dotstar" LEDsKevin O'Connor2019-08-061-3/+20
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* tmc_uart: Add support for configuring the uart address on tmc2209 chipsKevin O'Connor2019-07-311-0/+4
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* mcp4728: Update to better match printrbot revf requirementsKevin O'Connor2019-07-261-8/+9
| | | | | | Reported by @Grumps49. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* neopixel: Add support for daisy-chained chipsKevin O'Connor2019-07-231-0/+4
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* neopixel: Add support for setting a default color at startupKevin O'Connor2019-07-231-0/+5
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* neopixel: Add initial support for "neopixel" ledsKevin O'Connor2019-07-121-0/+10
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* firmware_retract: Remove z_hop supportKevin O'Connor2019-07-101-3/+0
| | | | | | | | | | | | The current z_hop support did not work correctly with common slicers that change Z height between retract and unretract, and it did not work correctly with slicers that issue a retract at the end of a print and then at the beginning of the next print. The z_hop support is therefore being removed until these issues can be fixed. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* docs: Add documentation for [delayed_gcode]Arksine2019-07-011-0/+13
| | | | Signed-off-by: Eric Callahan <arksine.code@gmail.com>
* docs: Update for latest changs to skew_correctionArksine2019-06-291-18/+5
| | | | Signed-off-by: Eric Callahan <arksine.code@gmail.com>
* tmc: Add support for virtual enable pinsKevin O'Connor2019-06-281-5/+20
| | | | | | | Add support for enabling the stepper via the communication channel. This improves support for boards with a shared enable line. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* skew_correction: add documentationArksine2019-06-261-0/+22
| | | | Signed-Off-By: Eric Callahan <arksine.code@gmail.com>
* config: No need to list all tmc drivers in endstop_phase descriptionKevin O'Connor2019-06-231-3/+3
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Update example-extras.cfg for tmc2209Kevin O'Connor2019-06-231-0/+36
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* gcode_button: Execute gcode when a button is pressed or released (#1745)Alec B. Plumb2019-06-211-0/+15
| | | | | | | An extra to execute gcode when a hardware button is pressed or released. Uses the jinja2 templating system. Inspired by pull request #545 from Miguel Moitinho miguel@moitinho.net and pull request #1098 from Paulo Drugos paulodrugos@gmail.com Signed-off-by: Alec Plumb <alec@etherwalker.com>
* probe: Add support for samples_toleranceKevin O'Connor2019-06-211-0/+12
| | | | | | Add a check on the maximum Z distance between probe samples. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* tmc2660: Don't allow configuration of DEDGEKevin O'Connor2019-06-181-1/+0
| | | | | | Setting DEDGE would just break the code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
generated by cgit v1.2.3-70-g09d2 (git 2.50.1) at 2025-09-02 08:16:43 +0000