klippy: Convert printer_state("connect") to an event handler

Convert all users of the printer_state("connect") handler to register
a "klippy:connect" event handler instead.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

6 files changed, 29 insertions, 28 deletions

diff --git a/klippy/extras/bed_mesh.py b/klippy/extras/bed_mesh.py
index 1625bbcc..dc6eba33 100644
--- a/klippy/extras/bed_mesh.py
+++ b/klippy/extras/bed_mesh.py
@@ -53,6 +53,8 @@ class BedMesh:
     FADE_DISABLE = 0x7FFFFFFF
     def __init__(self, config):
         self.printer = config.get_printer()
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         self.last_position = [0., 0., 0., 0.]
         self.calibrate = BedMeshCalibrate(config, self)
         self.z_mesh = None
@@ -74,10 +76,9 @@ class BedMesh:
             'BED_MESH_CLEAR', self.cmd_BED_MESH_CLEAR,
             desc=self.cmd_BED_MESH_CLEAR_help)
         self.gcode.set_move_transform(self)
-    def printer_state(self, state):
-        if state == 'connect':
-            self.toolhead = self.printer.lookup_object('toolhead')
-            self.calibrate.load_default_profile()
+    def handle_connect(self):
+        self.toolhead = self.printer.lookup_object('toolhead')
+        self.calibrate.load_default_profile()
     def set_mesh(self, mesh):
         if mesh is not None:
             if self.base_fade_target is None:
diff --git a/klippy/extras/bed_tilt.py b/klippy/extras/bed_tilt.py
index 50e0bcff..b94bf189 100644
--- a/klippy/extras/bed_tilt.py
+++ b/klippy/extras/bed_tilt.py
@@ -9,6 +9,8 @@ import probe, mathutil
 class BedTilt:
     def __init__(self, config):
         self.printer = config.get_printer()
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         self.x_adjust = config.getfloat('x_adjust', 0.)
         self.y_adjust = config.getfloat('y_adjust', 0.)
         self.z_adjust = config.getfloat('z_adjust', 0.)
@@ -18,9 +20,8 @@ class BedTilt:
         # Register move transform with g-code class
         gcode = self.printer.lookup_object('gcode')
         gcode.set_move_transform(self)
-    def printer_state(self, state):
-        if state == 'connect':
-            self.toolhead = self.printer.lookup_object('toolhead')
+    def handle_connect(self):
+        self.toolhead = self.printer.lookup_object('toolhead')
     def get_position(self):
         x, y, z, e = self.toolhead.get_position()
         return [x, y, z - x*self.x_adjust - y*self.y_adjust - self.z_adjust, e]
diff --git a/klippy/extras/quad_gantry_level.py b/klippy/extras/quad_gantry_level.py
index b9f91f1f..0b1768e5 100644
--- a/klippy/extras/quad_gantry_level.py
+++ b/klippy/extras/quad_gantry_level.py
@@ -9,6 +9,8 @@ import probe
 class QuadGantryLevel:
     def __init__(self, config):
         self.printer = config.get_printer()
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         self.probe_helper = probe.ProbePointsHelper(config, self.probe_finalize)
         gantry_corners = config.get('gantry_corners').split('\n')
         try:
@@ -27,9 +29,6 @@ class QuadGantryLevel:
         self.gcode.register_command(
             'QUAD_GANTRY_LEVEL', self.cmd_QUAD_GANTRY_LEVEL,
             desc=self.cmd_QUAD_GANTRY_LEVEL_help)
-    def printer_state(self, state):
-        if state == 'connect':
-            self.handle_connect()
     def handle_connect(self):
         kin = self.printer.lookup_object('toolhead').get_kinematics()
         z_steppers = kin.get_steppers('Z')
diff --git a/klippy/extras/tmc2208.py b/klippy/extras/tmc2208.py
index a86a86d8..3058f291 100644
--- a/klippy/extras/tmc2208.py
+++ b/klippy/extras/tmc2208.py
@@ -95,6 +95,8 @@ class TMC2208:
     def __init__(self, config):
         self.printer = config.get_printer()
         self.name = config.get_name().split()[1]
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         # pin setup
         ppins = self.printer.lookup_object("pins")
         rx_pin_params = ppins.lookup_pin(
@@ -191,10 +193,9 @@ class TMC2208:
         cmd_queue = self.mcu.alloc_command_queue()
         self.tmcuart_send_cmd = self.mcu.lookup_command(
             "tmcuart_send oid=%c write=%*s read=%c", cq=cmd_queue)
-    def printer_state(self, state):
-        if state == 'connect':
-            for reg_name, val in self.init_regs.items():
-                self.set_register(reg_name, val)
+    def handle_connect(self):
+        for reg_name, val in self.init_regs.items():
+            self.set_register(reg_name, val)
     def get_register(self, reg_name):
         reg = Registers[reg_name]
         msg = encode_tmc2208_read(0xf5, 0x00, reg)
diff --git a/klippy/extras/verify_heater.py b/klippy/extras/verify_heater.py
index 378a8b94..507ee33b 100644
--- a/klippy/extras/verify_heater.py
+++ b/klippy/extras/verify_heater.py
@@ -13,6 +13,8 @@ for the parameters that control this check.
 class HeaterCheck:
     def __init__(self, config):
         self.printer = config.get_printer()
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         self.printer.register_event_handler("klippy:shutdown",
                                             self.handle_shutdown)
         self.heater_name = config.get_name().split()[1]
@@ -29,17 +31,15 @@ class HeaterCheck:
         self.last_target = self.goal_temp = self.error = 0.
         self.fault_systime = self.printer.get_reactor().NEVER
         self.check_timer = None
-    def printer_state(self, state):
-        if state == 'connect':
-            if self.printer.get_start_args().get('debugoutput') is not None:
-                # Disable verify_heater if outputting to a debug file
-                return
-            pheater = self.printer.lookup_object('heater')
-            self.heater = pheater.lookup_heater(self.heater_name)
-            logging.info("Starting heater checks for %s", self.heater_name)
-            reactor = self.printer.get_reactor()
-            self.check_timer = reactor.register_timer(self.check_event,
-                                                      reactor.NOW)
+    def handle_connect(self):
+        if self.printer.get_start_args().get('debugoutput') is not None:
+            # Disable verify_heater if outputting to a debug file
+            return
+        pheater = self.printer.lookup_object('heater')
+        self.heater = pheater.lookup_heater(self.heater_name)
+        logging.info("Starting heater checks for %s", self.heater_name)
+        reactor = self.printer.get_reactor()
+        self.check_timer = reactor.register_timer(self.check_event, reactor.NOW)
     def handle_shutdown(self):
         if self.check_timer is not None:
             reactor = self.printer.get_reactor()
diff --git a/klippy/extras/z_tilt.py b/klippy/extras/z_tilt.py
index 4e748dd0..04b7d4c1 100644
--- a/klippy/extras/z_tilt.py
+++ b/klippy/extras/z_tilt.py
@@ -9,6 +9,8 @@ import probe, mathutil
 class ZTilt:
     def __init__(self, config):
         self.printer = config.get_printer()
+        self.printer.register_event_handler("klippy:connect",
+                                            self.handle_connect)
         z_positions = config.get('z_positions').split('\n')
         try:
             z_positions = [line.split(',', 1)
@@ -27,9 +29,6 @@ class ZTilt:
         self.gcode.register_command(
             'Z_TILT_ADJUST', self.cmd_Z_TILT_ADJUST,
             desc=self.cmd_Z_TILT_ADJUST_help)
-    def printer_state(self, state):
-        if state == 'connect':
-            self.handle_connect()
     def handle_connect(self):
         kin = self.printer.lookup_object('toolhead').get_kinematics()
         z_steppers = kin.get_steppers('Z')