config: Use "stealthchop_threshold: 999999" if set

Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 12 insertions, 12 deletions

diff --git a/config/generic-fysetc-s6.cfg b/config/generic-fysetc-s6.cfg
index 2ba301de..0f212665 100644
--- a/config/generic-fysetc-s6.cfg
+++ b/config/generic-fysetc-s6.cfg
@@ -114,42 +114,42 @@ max_z_accel: 100
 #tx_pin: PE9
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PE13
 #tx_pin: PE14
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PD12
 #tx_pin: PD11
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 100
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PA15
 #tx_pin: PD3
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PC5
 #tx_pin: PC4
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PE0
 #tx_pin: PE1
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 ########################################
 # TMC SPI configuration
@@ -172,7 +172,7 @@ max_z_accel: 100
 #diag1_pin: PB14
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
 #spi_bus: spi1
@@ -180,7 +180,7 @@ max_z_accel: 100
 #diag1_pin: PB13
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
 #spi_bus: spi1
@@ -188,7 +188,7 @@ max_z_accel: 100
 #diag1_pin: PA0
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #spi_bus: spi1
@@ -196,7 +196,7 @@ max_z_accel: 100
 #diag1_pin: PA3
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
 #spi_bus: spi1
@@ -204,7 +204,7 @@ max_z_accel: 100
 #diag1_pin: PA2
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
 #spi_bus: spi1
@@ -212,7 +212,7 @@ max_z_accel: 100
 #diag1_pin: PA1
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 ########################################
 # EXP1 / EXP2 (display) pins