config: Use "stealthchop_threshold: 999999" if set

Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 12 insertions, 12 deletions

diff --git a/config/generic-fysetc-f6.cfg b/config/generic-fysetc-f6.cfg
index dfb76e6e..31397543 100644
--- a/config/generic-fysetc-f6.cfg
+++ b/config/generic-fysetc-f6.cfg
@@ -113,42 +113,42 @@ pins: PB0
 #tx_pin: PJ2
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PJ3
 #tx_pin: PJ4
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PE2
 #tx_pin: PE6
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 100
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PJ5
 #tx_pin: PJ6
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PE7
 #tx_pin: PD4
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PA1
 #tx_pin: PD5
 #run_current: 0.8
 #hold_current: 0.5
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 ########################################
 # TMC SPI configuration
@@ -167,42 +167,42 @@ pins: PB0
 #diag1_pin: PK1
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
 #cs_pin: PG2
 #diag1_pin: PJ1
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
 #cs_pin: PJ7
 #diag1_pin: PB6
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #cs_pin: PL2
 #diag1_pin: PE4
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
 #cs_pin: PC5
 #diag1_pin: PJ0
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
 #cs_pin: PL7
 #diag1_pin: PK2
 #run_current: 0.800
 #hold_current: 0.500
-#stealthchop_threshold: 250
+#stealthchop_threshold: 999999
 
 ########################################
 # EXP1 / EXP2 (display) pins