config: Add BigTreeTech Manta M4P & M8P board (#5812)

Signed-off-by: Alan.Ma from BigTreeTech <tech@biqu3d.com>

1 files changed, 175 insertions, 0 deletions

diff --git a/config/generic-bigtreetech-manta-m4p.cfg b/config/generic-bigtreetech-manta-m4p.cfg
new file mode 100644
index 00000000..efd9007d
--- /dev/null
+++ b/config/generic-bigtreetech-manta-m4p.cfg
@@ -0,0 +1,175 @@
+# This file contains common pin mappings for the BIGTREETECH Manta M4P
+# To use this config, the firmware should be compiled for the
+# STM32G0B1 with a "8KiB bootloader" and USB communication.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC6
+dir_pin: PA14
+enable_pin: !PC7
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PC0
+position_endstop: 0
+position_max: 235
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB10
+dir_pin: !PB2
+enable_pin: !PB11
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PC1
+position_endstop: 0
+position_max: 235
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB0
+dir_pin: !PC5
+enable_pin: !PB1
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^PC2
+position_endstop: 0
+position_max: 270
+
+[extruder]
+step_pin: PB3
+dir_pin: PB4
+enable_pin: !PD5
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PC8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA0
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+#[filament_switch_sensor filament_sensor]
+#switch_pin: ^!PC15
+
+[heater_bed]
+heater_pin: PD8
+sensor_type: Generic 3950
+sensor_pin: PC4
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PD2
+
+#[heater_fan fan1]
+#pin: PD3
+
+#[heater_fan fan2]
+#pin: PD4
+
+#[heater_fan SoC_fan]
+#pin: CB1: gpio79
+#pin: RPI: gpio26
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 180
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PD6,  EXP1_3=PB9,  EXP1_5=PA15, EXP1_7=PA9,   EXP1_9=<GND>,
+    EXP1_2=PB8,  EXP1_4=PC3,  EXP1_6=PA10, EXP1_8=PB5,   EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB14, EXP2_3=PC11, EXP2_5=PC12, EXP2_7=PC13,  EXP2_9=<GND>,
+    EXP2_2=PB13, EXP2_4=PA8,  EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.
+
+########################################
+# TMC2209 configuration
+########################################
+
+#[tmc2209 stepper_x]
+#uart_pin: PB12
+#run_current: 0.800
+#diag_pin:
+
+#[tmc2209 stepper_y]
+#uart_pin: PC10
+#run_current: 0.800
+#diag_pin:
+
+#[tmc2209 stepper_z]
+#uart_pin: PC9
+#run_current: 0.800
+#diag_pin:
+
+#[tmc2209 extruder]
+#uart_pin: PA13
+#run_current: 0.600
+#diag_pin:
+
+########################################
+# TMC5160 configuration
+########################################
+
+#[[tmc2130 stepper_x]
+#cs_pin: PB12
+#spi_bus: spi1
+#diag1_pin: PG6
+#run_current: 0.800
+#stealthchop_threshold: 999999
+
+#[tmc2130 stepper_y]
+#cs_pin: PC10
+#spi_bus: spi1
+#diag1_pin: PG9
+#run_current: 0.800
+#stealthchop_threshold: 999999
+
+#[tmc2130 stepper_z]
+#cs_pin: PC9
+#spi_bus: spi1
+#diag1_pin: PG10
+#run_current: 0.650
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder]
+#cs_pin: PA13
+#spi_bus: spi1
+#diag1_pin: PC15
+#run_current: 0.650
+#stealthchop_threshold: 999999
+
+#[bltouch]
+#sensor_pin: PC14
+#control_pin: PA1
+
+#[adxl345]
+#cs_pin: PD9
+#spi_bus: spi1
+#axes_map: z,y,-x
+
+#[neopixel rgb1]
+#pin: PD0
+
+#[neopixel rgb2]
+#pin: PD1