chipmisc: Add support for statically configured output pins

Allow digital and PWM output pins to be setup via new config
sections.  This makes it easier to setup pin configurations.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 2 insertions, 36 deletions

diff --git a/config/example.cfg b/config/example.cfg
index 4bb805db..32ece835 100644
--- a/config/example.cfg
+++ b/config/example.cfg
@@ -2,7 +2,8 @@
 # copy and edit this file to configure a new cartesian style
 # printer. For delta style printers, see the "example-delta.cfg"
 # file. For corexy/h-bot style printers, see the "example-corexy.cfg"
-# file.
+# file. Only common config sections are described here - see the
+# "example-extras.cfg" file for configuring less common devices.
 
 # DO NOT COPY THIS FILE WITHOUT CAREFULLY READING AND UPDATING IT
 # FIRST. Incorrectly configured parameters may cause damage.
@@ -150,18 +151,6 @@ filament_diameter: 3.500
 #   otherwise cause retraction followed immediately by pressure
 #   buildup. This setting only applies if pressure_advance is
 #   non-zero. The default is 0.010 (10 milliseconds).
-#deactivate_gcode:
-#   A list of G-Code commands (one per line) to execute on a G-Code
-#   tool change command (eg, "T1") that deactivates this extruder and
-#   activates some other extruder. It only makes sense to define this
-#   section on multi-extruder printers. The default is to not run any
-#   special G-Code commands on deactivation.
-#activate_gcode:
-#   A list of G-Code commands (one per line) to execute on a G-Code
-#   tool change command (eg, "T0") that activates this extruder. It
-#   only makes sense to define this section on multi-extruder
-#   printers. The default is to not run any special G-Code commands on
-#   activation.
 #
 # The remaining variables describe the extruder heater.
 heater_pin: ar10
@@ -217,15 +206,6 @@ max_temp: 210
 #   Maximum temperature (mcu will shutdown if temperature is above
 #   this value). This parameter must be provided.
 
-# In a multi-extruder printer add an additional extruder section for
-# each additional extruder. The additional extruder sections should be
-# named "extruder1", "extruder2", "extruder3", and so on. See the
-# "extruder" section above for a description of available parameters.
-#[extruder1]
-#step_pin: ar36
-#dir_pin: ar34
-#...
-
 # The heater_bed section describes a heated bed (if present - omit
 # section if not present).
 [heater_bed]
@@ -323,17 +303,3 @@ max_z_accel: 30
 #   centripetal velocity cornering algorithm. A larger number will
 #   permit higher "cornering speeds" at the junction of two moves. The
 #   default is 0.02mm.
-
-# Heater cooling fans (one may define any number of sections with a
-# "heater_fan" prefix). A "heater fan" is a fan that will be enabled
-# whenever its associated heater is active.
-#[heater_fan my_nozzle_fan]
-# See the "fan" section for fan configuration parameters.
-#pin: ar4
-# The remaining variables are specific to heater_fan.
-#heater: extruder
-#   Name of the config section defining the heater that this fan is
-#   associated with.  The default is "extruder".
-#heater_temp: 50.0
-#   A temperature (in Celsius) that the heater must drop below before
-#   the fan is disabled. The default is 50 Celsius.