blob: d766c9d63dfb69e0d6af5cde1667da24d3ee8d6b (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
|
# Test config with macros
[stepper_x]
step_pin: ar54
dir_pin: ar55
enable_pin: !ar38
step_distance: .0125
endstop_pin: ^ar3
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: ar60
dir_pin: !ar61
enable_pin: !ar56
step_distance: .0125
endstop_pin: ^ar14
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: ar46
dir_pin: ar48
enable_pin: !ar62
step_distance: .0025
endstop_pin: ^ar18
position_endstop: 0.5
position_max: 200
[extruder]
step_pin: ar26
dir_pin: ar28
enable_pin: !ar24
step_distance: .004242
nozzle_diameter: 0.500
filament_diameter: 3.500
heater_pin: ar10
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog13
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 210
[heater_bed]
heater_pin: ar8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog14
control: watermark
min_temp: 0
max_temp: 110
[mcu]
serial: /dev/ttyACM0
pin_map: arduino
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[gcode_macro TEST_SAVE_RESTORE]
gcode:
SAVE_GCODE_STATE NAME=TESTIT1
G92 Z10
RESTORE_GCODE_STATE NAME=TESTIT1
G92 Z0
[gcode_macro TEST_expression]
gcode:
{% if printer.gcode.gcode_position.x != 0.0 %}
M112
{% else %}
{ printer.gcode.action_respond_info("TEST_expression") }
{% endif %}
[gcode_macro TEST_variable]
variable_t: 12
gcode:
{ printer.gcode.action_respond_info("TEST_variable") }
{% if t|float - 12.0 != printer.toolhead.position.y %}
M112
{% endif %}
{% if printer["gcode_macro TEST_variable"].t|float - 12.0 != 0.0 %}
M112
{% endif %}
SET_GCODE_VARIABLE MACRO=TEST_variable VARIABLE=t VALUE=17
TEST_variable_part2
[gcode_macro TEST_variable_part2]
gcode:
{ printer.gcode.action_respond_info("TEST_variable_part2") }
{% if printer["gcode_macro TEST_variable"].t|float != 17.0 %}
M112
{% endif %}
[gcode_macro TEST_param]
gcode:
{ printer.gcode.action_respond_info("TEST_param") }
{% if params.T != "123" %}
M112
{% endif %}
# Main test start point
[gcode_macro TESTIT]
gcode:
TEST_SAVE_RESTORE
TEST_expression
TEST_variable
TEST_param T=123
|
