blob: 54041fa211d026cc5bc528d50662aff2f19d188c (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
[stepper_x]
step_pin: PF0
dir_pin: PF1
enable_pin: !PD7
microsteps: 16
rotation_distance: 40
endstop_pin: ^PE5
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: PF6
dir_pin: !PF7
enable_pin: !PF2
microsteps: 16
rotation_distance: 40
endstop_pin: ^PJ1
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
microsteps: 16
rotation_distance: 8
endstop_pin: ^PD3
position_endstop: 0.5
position_max: 200
[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
microsteps: 16
rotation_distance: 33.5
nozzle_diameter: 0.500
filament_diameter: 3.500
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 210
[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: watermark
min_temp: 0
max_temp: 110
[mcu]
serial: /dev/ttyACM0
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
# Test config for exclude_object
[exclude_object]
[gcode_macro M486]
gcode:
# Parameters known to M486 are as follows:
# [C<flag>] Cancel the current object
# [P<index>] Cancel the object with the given index
# [S<index>] Set the index of the current object.
# If the object with the given index has been canceled, this will cause
# the firmware to skip to the next object. The value -1 is used to
# indicate something that isn’t an object and shouldn’t be skipped.
# [T<count>] Reset the state and set the number of objects
# [U<index>] Un-cancel the object with the given index. This command will be
# ignored if the object has already been skipped
{% if 'exclude_object' not in printer %}
{action_raise_error("[exclude_object] is not enabled")}
{% endif %}
{% if 'T' in params %}
EXCLUDE_OBJECT RESET=1
{% for i in range(params.T | int) %}
EXCLUDE_OBJECT_DEFINE NAME={i}
{% endfor %}
{% endif %}
{% if 'C' in params %}
EXCLUDE_OBJECT CURRENT=1
{% endif %}
{% if 'P' in params %}
EXCLUDE_OBJECT NAME={params.P}
{% endif %}
{% if 'S' in params %}
{% if params.S == '-1' %}
{% if printer.exclude_object.current_object %}
EXCLUDE_OBJECT_END NAME={printer.exclude_object.current_object}
{% endif %}
{% else %}
EXCLUDE_OBJECT_START NAME={params.S}
{% endif %}
{% endif %}
{% if 'U' in params %}
EXCLUDE_OBJECT RESET=1 NAME={params.U}
{% endif %}
|
