1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
|
// Code to setup clocks and gpio on stm32l4
//
// Copyright (C) 2019 Kevin O'Connor <kevin@koconnor.net>
//
// This file may be distributed under the terms of the GNU GPLv3 license.
#include "autoconf.h" // CONFIG_CLOCK_REF_FREQ
#include "board/armcm_boot.h" // VectorTable
#include "board/irq.h" // irq_disable
#include "board/misc.h" // bootloader_request
#include "command.h" // DECL_CONSTANT_STR
#include "internal.h" // enable_pclock
#include "sched.h" // sched_main
#define FREQ_PERIPH_DIV 1
#define FREQ_PERIPH (CONFIG_CLOCK_FREQ / FREQ_PERIPH_DIV)
// Map a peripheral address to its enable bits
struct cline
lookup_clock_line(uint32_t periph_base)
{
if (periph_base < APB2PERIPH_BASE) {
uint32_t pos = (periph_base - APB1PERIPH_BASE) / 0x400;
if (pos < 32) {
return (struct cline){.en = &RCC->APB1ENR1,
.rst = &RCC->APB1RSTR1,
.bit = 1 << pos};
} else {
return (struct cline){.en = &RCC->APB1ENR2,
.rst = &RCC->APB1RSTR2,
.bit = 1 << (pos - 32)};
}
} else if (periph_base < AHB1PERIPH_BASE) {
uint32_t pos = (periph_base - APB2PERIPH_BASE) / 0x400;
return (struct cline){.en = &RCC->APB2ENR,
.rst = &RCC->APB2RSTR,
.bit = 1 << pos};
} else if (periph_base < AHB2PERIPH_BASE) {
uint32_t pos = (periph_base - AHB1PERIPH_BASE) / 0x400;
return (struct cline){.en = &RCC->AHB1ENR,
.rst = &RCC->AHB1RSTR,
.bit = 1 << pos};
} else if (periph_base == ADC12_COMMON_BASE) {
return (struct cline){.en = &RCC->AHB2ENR,
.rst = &RCC->AHB2RSTR,
.bit = RCC_AHB2ENR_ADCEN};
}
return (struct cline){.en = &RCC->AHB2ENR,
.rst = &RCC->AHB2RSTR,
.bit = 0};
}
// Return the frequency of the given peripheral clock
uint32_t
get_pclock_frequency(uint32_t periph_base)
{
return FREQ_PERIPH;
}
// Enable a GPIO peripheral clock
void
gpio_clock_enable(GPIO_TypeDef *regs)
{
uint32_t rcc_pos = ((uint32_t)regs - GPIOA_BASE) / 0x400;
RCC->AHB2ENR |= 1 << rcc_pos;
RCC->AHB2ENR;
}
// PLL (L412) input: 4 to 16Mhz, vco: 96 to 344Mhz, output: 12 to 80Mhz
#if !CONFIG_STM32_CLOCK_REF_INTERNAL
DECL_CONSTANT_STR("RESERVE_PINS_crystal", "PC14,PC15");
#endif
static void
enable_clock_stm32l4(void)
{
uint32_t pll_base = 4000000, pll_freq = CONFIG_CLOCK_FREQ * 2, pllcfgr;
if (!CONFIG_STM32_CLOCK_REF_INTERNAL) {
// Configure 80Mhz PLL from external crystal (HSE)
uint32_t div = CONFIG_CLOCK_REF_FREQ / pll_base - 1;
RCC->CR |= RCC_CR_HSEON;
while (!(RCC->CR & RCC_CR_HSERDY))
;
pllcfgr = RCC_PLLCFGR_PLLSRC_HSE | (div << RCC_PLLCFGR_PLLM_Pos);
} else {
// Configure 80Mhz PLL from internal 16Mhz oscillator (HSI)
uint32_t div = 16000000 / pll_base - 1;
pllcfgr = RCC_PLLCFGR_PLLSRC_HSI | (div << RCC_PLLCFGR_PLLM_Pos);
RCC->CR |= RCC_CR_HSION;
while (!(RCC->CR & RCC_CR_HSIRDY))
;
}
RCC->PLLCFGR = (pllcfgr | ((pll_freq/pll_base) << RCC_PLLCFGR_PLLN_Pos)
| (0 << RCC_PLLCFGR_PLLR_Pos));
RCC->CR |= RCC_CR_PLLON;
// Enable 48Mhz USB clock using clock recovery
if (CONFIG_USB) {
RCC->CRRCR |= RCC_CRRCR_HSI48ON;
while (!(RCC->CRRCR & RCC_CRRCR_HSI48RDY))
;
enable_pclock(CRS_BASE);
CRS->CR |= CRS_CR_AUTOTRIMEN | CRS_CR_CEN;
enable_pclock(PWR_BASE);
PWR->CR2 |= PWR_CR2_USV;
}
}
// Main clock setup called at chip startup
static void
clock_setup(void)
{
enable_clock_stm32l4();
// Set flash latency
uint32_t latency = ((CONFIG_CLOCK_FREQ>64000000) ? FLASH_ACR_LATENCY_4WS :
((CONFIG_CLOCK_FREQ>48000000) ? FLASH_ACR_LATENCY_3WS :
((CONFIG_CLOCK_FREQ>32000000) ? FLASH_ACR_LATENCY_2WS :
((CONFIG_CLOCK_FREQ>16000000) ? FLASH_ACR_LATENCY_1WS :
FLASH_ACR_LATENCY_0WS))));
FLASH->ACR = (latency | FLASH_ACR_ICEN | FLASH_ACR_DCEN
| FLASH_ACR_PRFTEN);
// Wait for PLL lock
while (!(RCC->CR & RCC_CR_PLLRDY))
;
RCC->PLLCFGR |= RCC_PLLCFGR_PLLREN;
// Switch system clock to PLL
RCC->CFGR = RCC_CFGR_HPRE_DIV1 | RCC_CFGR_PPRE1_DIV1 | RCC_CFGR_PPRE2_DIV1
| RCC_CFGR_SW_PLL;
while ((RCC->CFGR & RCC_CFGR_SWS_Msk) != RCC_CFGR_SWS_PLL)
;
}
/****************************************************************
* Bootloader
****************************************************************/
// Handle USB reboot requests
void
bootloader_request(void)
{
dfu_reboot();
}
/****************************************************************
* Startup
****************************************************************/
// Main entry point - called from armcm_boot.c:ResetHandler()
void
armcm_main(void)
{
dfu_reboot_check();
// Run SystemInit() and then restore VTOR
SystemInit();
SCB->VTOR = (uint32_t)VectorTable;
clock_setup();
sched_main();
}
|
