blob: ea2300ecffd949d128052c33cc8f0e04f9acd5f2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
# Main Kconfig settings
mainmenu "Klipper Firmware Configuration"
config LOW_LEVEL_OPTIONS
bool "Enable extra low-level configuration options"
default n
help
Enable low-level configuration options that (if modified) may
result in a build that does not function correctly.
choice
prompt "Micro-controller Architecture"
config MACH_AVR
bool "Atmega AVR"
config MACH_ATSAM
bool "SAM3/SAM4/SAM E70 (Due and Duet)"
config MACH_ATSAMD
bool "SAMD21/SAMD51"
config MACH_LPC176X
bool "LPC176x (Smoothieboard)"
config MACH_STM32
bool "STMicroelectronics STM32"
config MACH_RP2040
bool "Raspberry Pi RP2040"
config MACH_PRU
bool "Beaglebone PRU"
config MACH_LINUX
bool "Linux process"
config MACH_SIMU
bool "Host simulator"
endchoice
source "src/avr/Kconfig"
source "src/atsam/Kconfig"
source "src/atsamd/Kconfig"
source "src/lpc176x/Kconfig"
source "src/stm32/Kconfig"
source "src/rp2040/Kconfig"
source "src/pru/Kconfig"
source "src/linux/Kconfig"
source "src/simulator/Kconfig"
# Generic configuration options for serial ports
config SERIAL_BAUD
depends on SERIAL
int "Baud rate for serial port" if LOW_LEVEL_OPTIONS
default 250000
help
Specify the baud rate of the serial port. This should be set
to 250000. Read the FAQ before changing this value.
# Generic configuration options for USB
config USB_VENDOR_ID
default 0x1d50
config USB_DEVICE_ID
default 0x614e
config USB_SERIAL_NUMBER_CHIPID
depends on HAVE_CHIPID
default y
config USB_SERIAL_NUMBER
default "12345"
menu "USB ids"
depends on USBSERIAL && LOW_LEVEL_OPTIONS
config USB_VENDOR_ID
hex "USB vendor ID"
config USB_DEVICE_ID
hex "USB device ID"
config USB_SERIAL_NUMBER_CHIPID
bool "USB serial number from CHIPID" if HAVE_CHIPID
config USB_SERIAL_NUMBER
string "USB serial number" if !USB_SERIAL_NUMBER_CHIPID
endmenu
config INITIAL_PINS
string "GPIO pins to set at micro-controller startup"
depends on LOW_LEVEL_OPTIONS
help
One may specify a comma separated list of gpio pins to set
during the micro-controller startup sequence. By default the
pins will be set to output high - preface a pin with a '!'
character to set that pin to output low.
# The HAVE_x options allow boards to disable support for some commands
# if the hardware does not support the feature.
config HAVE_GPIO
bool
default n
config HAVE_GPIO_ADC
bool
default n
config HAVE_GPIO_SPI
bool
default n
config HAVE_GPIO_I2C
bool
default n
config HAVE_GPIO_HARD_PWM
bool
default n
config HAVE_GPIO_BITBANGING
bool
default n
config HAVE_STRICT_TIMING
bool
default n
config HAVE_CHIPID
bool
default n
config HAVE_STEPPER_BOTH_EDGE
bool
default n
config INLINE_STEPPER_HACK
# Enables gcc to inline stepper_event() into the main timer irq handler
bool
depends on HAVE_GPIO
default y
|
