blob: ef1fcfe59e6cc2df6064a159ae70726843069d0d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
# Main Kconfig settings
mainmenu "Klipper Firmware Configuration"
config LOW_LEVEL_OPTIONS
bool "Enable extra low-level configuration options"
default n
help
Enable low-level configuration options that (if modified) may
result in a build that does not function correctly.
choice
prompt "Micro-controller Architecture"
config MACH_AVR
bool "Atmega AVR"
config MACH_ATSAM
bool "SAM3/SAM4 (Due and Duet)"
config MACH_ATSAMD
bool "SAMD21/SAMD51"
config MACH_LPC176X
bool "LPC176x (Smoothieboard)"
config MACH_STM32
bool "STMicroelectronics STM32F1/F4"
config MACH_STM32F0_HAL
bool "STMicroelectronics STM32F042"
config MACH_PRU
bool "Beaglebone PRU"
config MACH_LINUX
bool "Linux process"
config MACH_SIMU
bool "Host simulator"
endchoice
source "src/avr/Kconfig"
source "src/atsam/Kconfig"
source "src/atsamd/Kconfig"
source "src/lpc176x/Kconfig"
source "src/stm32/Kconfig"
source "src/stm32f0/Kconfig"
source "src/pru/Kconfig"
source "src/linux/Kconfig"
source "src/simulator/Kconfig"
# Generic configuration options for serial ports
config SERIAL_BAUD
depends on SERIAL
int "Baud rate for serial port" if LOW_LEVEL_OPTIONS
default 250000
help
Specify the baud rate of the serial port. This should be set
to 250000. Read the FAQ before changing this value.
# Generic configuration options for USB
menu "USB ids"
depends on USBSERIAL
config USB_VENDOR_ID
hex "USB vendor ID"
default 0x2341
config USB_DEVICE_ID
hex "USB device ID"
default 0xabcd
config USB_SERIAL_NUMBER
string "USB serial number"
default "12345"
endmenu
# Step timing customization
config CUSTOM_STEP_DELAY
bool "Specify a custom step pulse duration"
depends on LOW_LEVEL_OPTIONS
config STEP_DELAY
int
default 2
config STEP_DELAY
int "Step pulse duration (in microseconds)"
depends on CUSTOM_STEP_DELAY
help
Specify the duration of the stepper step pulse time. This
setting applies to all stepper drivers controlled by the
micro-controller. If this value is set to zero (or less) then
the code will "step" and "unstep" in the same C function.
A setting of zero (or less) on 8-bit AVR micro-controllers
results in a minimum step pulse time a little over 2us.
A setting of zero on ARM micro-controllers typically results
in a minimum step pulse time of 20 cpu cycles.
The default for AVR is -1, for all other micro-controllers it
is 2us.
config INITIAL_PINS
string "GPIO pins to set at micro-controller startup"
depends on LOW_LEVEL_OPTIONS
help
One may specify a comma separated list of gpio pins to set
during the micro-controller startup sequence. By default the
pins will be set to output high - preface a pin with a '!'
character to set that pin to output low.
# The HAVE_GPIO_x options allow boards to disable support for some
# commands if the hardware does not support the feature.
config HAVE_GPIO
bool
default n
config HAVE_GPIO_ADC
bool
default n
config HAVE_GPIO_SPI
bool
default n
config HAVE_GPIO_I2C
bool
default n
config HAVE_GPIO_HARD_PWM
bool
default n
config HAVE_GPIO_BITBANGING
bool
default n
config INLINE_STEPPER_HACK
# Enables gcc to inline stepper_event() into the main timer irq handler
bool
depends on HAVE_GPIO
default y
|
