blob: 7278ada0cc29888a2a9bead7d298cf844f4e8f3d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
# Main Kconfig settings
mainmenu "Klipper Firmware Configuration"
config LOW_LEVEL_OPTIONS
bool "Enable extra low-level configuration options"
default n
help
Enable low-level configuration options that (if modified) may
result in a build that does not function correctly.
choice
prompt "Micro-controller Architecture"
config MACH_AVR
bool "Atmega AVR"
config MACH_ATSAM
bool "SAM3/SAM4 (Due and Duet)"
config MACH_ATSAMD
bool "SAMD21/SAMD51"
config MACH_LPC176X
bool "LPC176x (Smoothieboard)"
config MACH_STM32
bool "STMicroelectronics STM32"
config MACH_PRU
bool "Beaglebone PRU"
config MACH_LINUX
bool "Linux process"
config MACH_SIMU
bool "Host simulator"
endchoice
source "src/avr/Kconfig"
source "src/atsam/Kconfig"
source "src/atsamd/Kconfig"
source "src/lpc176x/Kconfig"
source "src/stm32/Kconfig"
source "src/pru/Kconfig"
source "src/linux/Kconfig"
source "src/simulator/Kconfig"
# Generic configuration options for serial ports
config SERIAL_BAUD
depends on SERIAL
int "Baud rate for serial port" if LOW_LEVEL_OPTIONS
default 250000
help
Specify the baud rate of the serial port. This should be set
to 250000. Read the FAQ before changing this value.
# Generic configuration options for USB
config USB_VENDOR_ID
default 0x1d50
config USB_DEVICE_ID
default 0x614e
config USB_SERIAL_NUMBER_CHIPID
depends on HAVE_CHIPID
default y
config USB_SERIAL_NUMBER
default "12345"
menu "USB ids"
depends on USBSERIAL && LOW_LEVEL_OPTIONS
config USB_VENDOR_ID
hex "USB vendor ID"
config USB_DEVICE_ID
hex "USB device ID"
config USB_SERIAL_NUMBER_CHIPID
bool "USB serial number from CHIPID" if HAVE_CHIPID
config USB_SERIAL_NUMBER
string "USB serial number" if !USB_SERIAL_NUMBER_CHIPID
endmenu
# Step timing customization
config CUSTOM_STEP_DELAY
bool "Specify a custom step pulse duration"
depends on LOW_LEVEL_OPTIONS
config STEP_DELAY
int
default 2
config STEP_DELAY
int "Step pulse duration (in microseconds)"
depends on CUSTOM_STEP_DELAY
help
Specify the duration of the stepper step pulse time. This
setting applies to all stepper drivers controlled by the
micro-controller. If this value is set to zero (or less) then
the code will "step" and "unstep" in the same C function.
A setting of zero (or less) on 8-bit AVR micro-controllers
results in a minimum step pulse time a little over 2us.
A setting of zero on ARM micro-controllers typically results
in a minimum step pulse time of 20 cpu cycles.
The default for AVR is -1, for all other micro-controllers it
is 2us.
config INITIAL_PINS
string "GPIO pins to set at micro-controller startup"
depends on LOW_LEVEL_OPTIONS
help
One may specify a comma separated list of gpio pins to set
during the micro-controller startup sequence. By default the
pins will be set to output high - preface a pin with a '!'
character to set that pin to output low.
# The HAVE_x options allow boards to disable support for some commands
# if the hardware does not support the feature.
config HAVE_GPIO
bool
default n
config HAVE_GPIO_ADC
bool
default n
config HAVE_GPIO_SPI
bool
default n
config HAVE_GPIO_I2C
bool
default n
config HAVE_GPIO_HARD_PWM
bool
default n
config HAVE_GPIO_BITBANGING
bool
default n
config HAVE_STRICT_TIMING
bool
default n
config HAVE_CHIPID
bool
default n
config INLINE_STEPPER_HACK
# Enables gcc to inline stepper_event() into the main timer irq handler
bool
depends on HAVE_GPIO
default y
|
