1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
|
# SHT3X i2c based temperature sensors support
#
# Copyright (C) 2024 Timofey Titovets <nefelim4ag@gmail.com>
# Based on htu21d.py code
#
# This file may be distributed under the terms of the GNU GPLv3 license.
import logging
from . import bus
######################################################################
# Compatible Sensors:
# SHT31 - Tested on octopus pro and Linux MCU
#
######################################################################
SHT3X_I2C_ADDR = 0x44
SHT3X_CMD = {
'MEASURE': {
'STRETCH_ENABLED': {
'HIGH_REP': [0x2c, 0x06], # High (15ms) repeatability measurement
'MED_REP': [0x2c, 0x0D], # Medium (6ms) repeatability measurement
'LOW_REP': [0x2c, 0x10], # Low (4ms) repeatability measurement
},
'STRETCH_DISABLED' : {
'HIGH_REP': [0x24, 0x00],
'MED_REP': [0x24, 0x0B],
'LOW_REP': [0x24, 0x16],
},
},
'OTHER': {
'STATUS': {
'READ': [0xF3, 0x2D],
'CLEAN': [0x30, 0x41],
},
'SOFTRESET': [0x30, 0xA2], # Soft reset
'HEATER': {
"ENABLE": [0x30, 0x6D],
"DISABLE": [0x30, 0x66],
},
'FETCH': [0xE0, 0x00],
'BREAK': [0x30, 0x93],
}
}
class SHT3X:
def __init__(self, config):
self.printer = config.get_printer()
self.name = config.get_name().split()[-1]
self.reactor = self.printer.get_reactor()
self.i2c = bus.MCU_I2C_from_config(
config, default_addr=SHT3X_I2C_ADDR, default_speed=100000)
self.report_time = config.getint('sht3x_report_time', 1, minval=1)
self.deviceId = config.get('sensor_type')
self.temp = self.min_temp = self.max_temp = self.humidity = 0.
self.sample_timer = self.reactor.register_timer(self._sample_sht3x)
self.printer.add_object("sht3x " + self.name, self)
self.printer.register_event_handler("klippy:connect",
self.handle_connect)
def handle_connect(self):
self._init_sht3x()
self.reactor.update_timer(self.sample_timer, self.reactor.NOW)
def setup_minmax(self, min_temp, max_temp):
self.min_temp = min_temp
self.max_temp = max_temp
def setup_callback(self, cb):
self._callback = cb
def get_report_time_delta(self):
return self.report_time
def _init_sht3x(self):
# Device Soft Reset
self.i2c.i2c_write(SHT3X_CMD['OTHER']['SOFTRESET'])
# Wait 2ms after reset
self.reactor.pause(self.reactor.monotonic() + .02)
status = self.i2c.i2c_read(SHT3X_CMD['OTHER']['STATUS']['READ'], 3)
response = bytearray(status['response'])
status = response[0] << 8
status |= response[1]
checksum = response[2]
if self._crc8(status) != checksum:
logging.warning("sht3x: Reading status - checksum error!")
def _sample_sht3x(self, eventtime):
try:
# Read Temeprature
params = self.i2c.i2c_write(
SHT3X_CMD['MEASURE']['STRETCH_ENABLED']['HIGH_REP']
)
# Wait
self.reactor.pause(self.reactor.monotonic()
+ .20)
params = self.i2c.i2c_read([], 6)
response = bytearray(params['response'])
rtemp = response[0] << 8
rtemp |= response[1]
if self._crc8(rtemp) != response[2]:
logging.warning(
"sht3x: Checksum error on Temperature reading!"
)
else:
self.temp = -45 + (175 * rtemp / 65535)
logging.debug("sht3x: Temperature %.2f " % self.temp)
rhumid = response[3] << 8
rhumid |= response[4]
if self._crc8(rhumid) != response[5]:
logging.warning("sht3x: Checksum error on Humidity reading!")
else:
self.humidity = 100 * rhumid / 65535
logging.debug("sht3x: Humidity %.2f " % self.humidity)
except Exception:
logging.exception("sht3x: Error reading data")
self.temp = self.humidity = .0
return self.reactor.NEVER
if self.temp < self.min_temp or self.temp > self.max_temp:
self.printer.invoke_shutdown(
"sht3x: temperature %0.1f outside range of %0.1f:%.01f"
% (self.temp, self.min_temp, self.max_temp))
measured_time = self.reactor.monotonic()
print_time = self.i2c.get_mcu().estimated_print_time(measured_time)
self._callback(print_time, self.temp)
return measured_time + self.report_time
def _split_bytes(self, data):
bytes = []
for i in range((data.bit_length() + 7) // 8):
bytes.append((data >> i*8) & 0xFF)
bytes.reverse()
return bytes
def _crc8(self, data):
#crc8 polynomial for 16bit value, CRC8 -> x^8 + x^5 + x^4 + 1
SHT3X_CRC8_POLYNOMINAL= 0x31
crc = 0xFF
data_bytes = self._split_bytes(data)
for byte in data_bytes:
crc ^= byte
for _ in range(8):
if crc & 0x80:
crc = (crc << 1) ^ SHT3X_CRC8_POLYNOMINAL
else:
crc <<= 1
return crc & 0xFF
def get_status(self, eventtime):
return {
'temperature': round(self.temp, 2),
'humidity': round(self.humidity, 1),
}
def load_config(config):
# Register sensor
pheater = config.get_printer().lookup_object("heaters")
pheater.add_sensor_factory("SHT3X", SHT3X)
|
