1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
# This is a Klipper configuration for TronXY X5SA, with CXY-V6
# motherboard.
# === FLASHING WITH STOCK BOOTLOADER ===
# You should make firmware for STM32F103 with bootloader offset
# at 0x8008800 (Chitu v6 Bootloader) and serial (on USART1 PA10/PA9)
# communication.
# Use "./scripts/update_chitu.py ./out/klipper.bin ./out/update.cbd"
# after make to generate update.cbd. Put `update.cbd` onto SD card,
# and reboot the printer. It will be automatically installed, and you
# will be able to update it this way.
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[printer]
kinematics: corexy
max_velocity: 300
max_accel: 3000
max_z_velocity: 25
max_z_accel: 30
[stepper_x]
step_pin: PE5
dir_pin: !PE6
enable_pin: !PC13
microsteps: 16
rotation_distance: 20
endstop_pin: !PG10
position_endstop: -1
position_min: -1
position_max: 350
homing_speed: 50
homing_retract_dist: 10
second_homing_speed: 10.0
[stepper_y]
step_pin: PE2
dir_pin: !PE3
enable_pin: !PE4
microsteps: 16
rotation_distance: 20
endstop_pin: !PA12
position_endstop: 0
position_max: 330
homing_retract_dist: 10
homing_speed: 50.0
second_homing_speed: 10.0
[stepper_z]
step_pin: PB9
dir_pin: PE0
enable_pin: !PE1
microsteps: 16
rotation_distance: 4
endstop_pin: probe:z_virtual_endstop
position_max: 400
position_min: -2
[extruder]
step_pin: PB4
dir_pin: PB5
enable_pin: !PB8
microsteps: 16
rotation_distance: 35.520
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PG12
sensor_type: ATC Semitec 104GT-2
sensor_pin: PA1
control: pid
pid_Kp: 18.831
pid_Ki: 0.821
pid_Kd: 108.044
min_temp: 0
max_temp: 250
max_extrude_only_distance: 300
[heater_bed]
heater_pin: PG11
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
control: pid
min_temp: 0
max_temp: 130
pid_Kp: 73.932
pid_Ki: 1.521
pid_Kd: 898.279
[heater_fan hotend_fan]
pin: PG14
[fan]
pin: PG13
[controller_fan drivers_fan]
pin: PD6
[filament_switch_sensor sentinel]
pause_on_runout: True
runout_gcode:
M25
switch_pin: PA15
[output_pin beeper]
pin: PB0
[safe_z_home]
home_xy_position: 165, 165
speed: 50
z_hop: 10
z_hop_speed: 5
[bed_screws]
screw1: 5, 5
screw2: 165, 5
screw3: 325, 5
screw4: 5, 325
screw5: 165, 325
screw6: 325, 325
[bed_mesh]
speed: 120
probe_count: 5, 5
horizontal_move_z: 5
algorithm: lagrange
mesh_min : 20, 20
mesh_max : 310, 310
mesh_pps: 0
[probe]
x_offset: -40
y_offset: 0
pin: !PG9
speed: 30
z_offset: 2
|
