blob: e9f179eeace10a7a0c9e1ecfbe11a05c2a1217af (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
|
# This file contains pin mappings for the stock Sovol SV06
# To use this config, during "make menuconfig" select the
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
# Also, since it is using the GD32F103, please select Disable SWD at startup
#
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.
#
# See docs/Config_Reference.md for a description of parameters.
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[stepper_x]
step_pin: PC2
dir_pin: !PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: tmc2209_stepper_x:virtual_endstop
position_endstop: 0
position_max: 220
homing_speed: 40
homing_retract_dist: 0
[tmc2209 stepper_x]
uart_pin: PC1
run_current: 0.860
stealthchop_threshold: 0
interpolate: False
sense_resistor: 0.150
uart_address: 3
driver_SGTHRS: 81
diag_pin: PA5
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: tmc2209_stepper_y:virtual_endstop
position_endstop: 0
position_max: 220
homing_speed: 40
homing_retract_dist: 0
[tmc2209 stepper_y]
uart_pin: PC0
run_current: 0.900
stealthchop_threshold: 0
interpolate: False
sense_resistor: 0.150
uart_address: 3
driver_SGTHRS: 82
diag_pin: PA6
[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 4
endstop_pin: probe:z_virtual_endstop
position_min: -4
position_max: 250
homing_speed: 4
[tmc2209 stepper_z]
uart_pin: PA15
run_current: 1.000
stealthchop_threshold: 0
interpolate: False
sense_resistor: 0.150
uart_address: 3
diag_pin: PA7
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: !PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 4.56
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_kd: 86.991
pid_kp: 21.479
pid_ki: 1.326
min_temp: 0
max_temp: 300
[tmc2209 extruder]
uart_pin: PC14
run_current: 0.550
stealthchop_threshold: 0
interpolate: False
sense_resistor: 0.150
uart_address: 3
[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_kp: 64.440
pid_ki: 0.773
pid_kd: 1343.571
min_temp: 0
max_temp: 130
[fan]
pin: PA0
[probe]
pin: PB1
x_offset: 27
y_offset: -20
z_offset: 0
samples: 2
samples_tolerance: 0.015
samples_tolerance_retries: 5
[safe_z_home]
home_xy_position: 85,135
z_hop: 10
z_hop_speed: 5
[bed_mesh]
speed: 120
horizontal_move_z: 5
mesh_min: 28, 20
mesh_max: 210, 205
probe_count: 10
algorithm: bicubic
fade_start: 1
fade_end: 10
fade_target: 0
[display]
lcd_type: st7920
cs_pin: PB12
sclk_pin: PB13
sid_pin: PB15
encoder_pins: ^PB14, ^PB10
click_pin: ^!PB2
|
