blob: 072f75afb9319fc750829b619ffd95e135c8076e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
|
# This file contains common pin mappings for the FlashForge-Creator-Pro
# To use this config, the firmware should be compiled for
# the Atmel atmega2560.
# Use the following command to flash the board:
# avrdude -c stk500v2 -p m2560 -P /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00 -b 57600 -D -U out/klipper.elf.hex
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PF1
dir_pin: !PF0
enable_pin: !PF2
microsteps: 16
rotation_distance: 34
endstop_pin: ^!PL1
position_endstop: 116
position_max: 116
position_min: -116
homing_speed: 50
[stepper_y]
step_pin: PF5
dir_pin: !PF4
enable_pin: !PF6
microsteps: 16
rotation_distance: 34
endstop_pin: ^!PL3
position_endstop: 80
position_max: 80
position_min: -80
homing_speed: 50
[stepper_z]
step_pin: PK1
dir_pin: !PK0
enable_pin: !PK2
microsteps: 16
rotation_distance: 8
endstop_pin: !PL6
position_endstop: -0.25
position_max: 181
position_min: -0.25
[extruder]
step_pin: PA3
dir_pin: !PA2
enable_pin: !PA4
microsteps: 16
rotation_distance: 33
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PH3
sensor_type: MAX6675
sensor_pin: PE3
spi_software_miso_pin: PE5
spi_software_sclk_pin: PE2
spi_software_mosi_pin: PA1 #dummy mosi pin
control: pid
pid_kp: 27.341
pid_ki: 1.293
pid_kd: 144.566
min_temp: 0
max_temp: 260
[extruder1]
step_pin: PA7
dir_pin: PA6
enable_pin: !PG2
microsteps: 16
rotation_distance: 33
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB5
sensor_type: MAX6675
sensor_pin: PE4
spi_software_miso_pin: PE5
spi_software_sclk_pin: PE2
spi_software_mosi_pin: PA1 #dummy mosi pin
control: pid
pid_kp: 27.341
pid_ki: 1.293
pid_kd: 144.566
min_temp: 0
max_temp: 260
[gcode_macro T0]
gcode:
SET_GCODE_OFFSET X=-34
ACTIVATE_EXTRUDER EXTRUDER=extruder
[gcode_macro T1]
gcode:
SET_GCODE_OFFSET X=0
ACTIVATE_EXTRUDER EXTRUDER=extruder1
[heater_fan extruder_fan]
pin: PH4
[heater_fan extruder1_fan]
pin: PB6
[fan]
pin: PL5
[heater_bed]
heater_pin: PL4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PK7
control: pid
pid_kp: 72.914
pid_ki: 2.060
pid_kd: 645.290
min_temp: 0
max_temp: 130
[mcu]
serial: /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 1000
max_z_velocity: 5
max_z_accel: 100
[mcp4018 x_axis_pot]
scl_pin: PJ5
sda_pin: PF3
wiper: 118
scale: 127
[mcp4018 y_axis_pot]
scl_pin: PJ5
sda_pin: PF7
wiper: 118
scale: 127
[mcp4018 z_axis_pot]
scl_pin: PJ5
sda_pin: PK3
wiper: 40
scale: 127
[mcp4018 a_axis_pot]
scl_pin: PJ5
sda_pin: PA5
wiper: 118
scale: 127
[mcp4018 b_axis_pot]
scl_pin: PJ5
sda_pin: PJ6
wiper: 118
scale: 127
[display]
lcd_type: hd44780_spi
spi_software_mosi_pin: PC3
spi_software_sclk_pin: PC2
#miso not used, dummy pin.
spi_software_miso_pin: PJ1
latch_pin: PC4
click_pin: ^PJ0
back_pin: ^PJ2
up_pin: ^PJ4
down_pin: ^PJ3
[pca9533 led_strip]
i2c_bus: twi
i2c_address: 98
initial_RED: 1
initial_GREEN: 1
initial_BLUE: 1
|
