1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
# This file contains an example configuration for the Replicape rev B3
# board. To use this config, one must compile and install the
# micro-controller code for the "Beaglebone PRU", and then compile and
# install the micro-controller code a second time for a "Linux
# process".
# NOTE: Klipper does not alter the input/output state of the
# Beaglebone pins and it does not control their pull-up resistors.
# Typically the correct settings are automatically applied when the
# Beaglebone detects the Replicape board, but if changes are needed
# they must be specified in a "device tree overlay" or via the
# config-pin program.
# See the example.cfg file for a description of available parameters.
[mcu]
serial: /dev/rpmsg_pru30
pin_map: beaglebone
[mcu host]
serial: /tmp/klipper_host_mcu
# The "replicape" config section adds "replicape:stepper_x_enable"
# virtual stepper enable pins (for steppers x, y, z, e, and h) and
# "replicape:power_x" PWM output pins (for hotbed, e, h, fan0, fan1,
# fan2, and fan3) that may then be used elsewhere in the config file.
[replicape]
revision: B3
# The replicape hardware revision. Currently only revision "B3" is
# supported. This parameter must be provided.
#enable_pin: !P9_41
# The replicape global enable pin. The default is !P9_41.
host_mcu: host
# The name of the mcu config section that communicates with the
# Klipper "linux process" mcu instance. This parameter must be
# provided.
#standstill_power_down: False
# This parameter controls the CFG6_ENN line on all stepper
# motors. True sets the enable lines to "open". The default is
# False.
#servo0_enable: False
# This parameter controls whether end_stop_X_2 is used for endstops
# (via P9_11) or for servo_0 (via P9_14). The default is False.
#servo1_enable: False
# This parameter controls whether end_stop_Y_2 is used for endstops
# (via P9_28) or for servo_1 (via P9_16). The default is False.
stepper_x_microstep_mode: spread16
# This parameter controls the CFG1 and CFG2 pins of the given
# stepper motor driver. Available options are: disable, 1, 2,
# spread2, 4, 16, spread4, spread16, stealth4, and stealth16. The
# default is disable.
stepper_x_current: 0.5
# The configured maximum current (in Amps) of the stepper motor
# driver. This parameter must be provided if the stepper is not in a
# disable mode.
#stepper_x_chopper_off_time_high: False
# This parameter controls the CFG0 pin of the stepper motor driver
# (True sets CFG0 high, False sets it low). The default is False.
#stepper_x_chopper_hysteresis_high: False
# This parameter controls the CFG4 pin of the stepper motor driver
# (True sets CFG4 high, False sets it low). The default is False.
#stepper_x_chopper_blank_time_high: True
# This parameter controls the CFG5 pin of the stepper motor driver
# (True sets CFG5 high, False sets it low). The default is True.
stepper_y_microstep_mode: spread16
stepper_y_current: 0.5
stepper_z_microstep_mode: spread16
stepper_z_current: 0.5
stepper_e_microstep_mode: 16
stepper_e_current: 0.5
[stepper_x]
step_pin: P8_17
dir_pin: P8_26
enable_pin: replicape:stepper_x_enable
step_distance: .0125
endstop_pin: ^P9_25
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: P8_12
dir_pin: P8_19
enable_pin: replicape:stepper_y_enable
step_distance: .0125
endstop_pin: ^P9_23
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: P8_13
dir_pin: P8_14
enable_pin: replicape:stepper_z_enable
step_distance: .0025
endstop_pin: ^P9_13
position_endstop: 0
position_max: 200
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 25
max_z_accel: 30
[extruder]
step_pin: P9_12
dir_pin: P8_15
enable_pin: replicape:stepper_e_enable
step_distance: .002
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: replicape:power_e
sensor_type: EPCOS 100K B57560G104F
sensor_pin: host:analog4
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
[heater_bed]
heater_pin: replicape:power_hotbed
sensor_type: EPCOS 100K B57560G104F
sensor_pin: host:analog6
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: replicape:power_fan0
|
