aboutsummaryrefslogtreecommitdiffstats
path: root/config/example-extras.cfg
Commit message (Collapse)AuthorAgeFilesLines
* thermistor: Add support for defining custom thermistorsKevin O'Connor2018-04-091-0/+25
| | | | | | Add the ability to define a new thermistor type in the config file. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Update indentation of display section in example-extras.cfgKevin O'Connor2018-04-091-9/+8
| | | | | | Use the same indentation as the other sections. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* probe: Add z_offset parameterKevin O'Connor2018-03-171-3/+3
| | | | | | | | | Move the probe_z_offset parameter from delta_calibrate and bed_tilt_calibrate to a z_offset parameter within the probe config section. It's easier to understand the z offset setting when it is in the probe config section. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* probe: Default z_position to the configured minimum position on Z axisKevin O'Connor2018-03-171-3/+0
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* output_pin: Move pwm and digital output pins to new module in extras/Kevin O'Connor2018-03-171-48/+29
| | | | | | | | Rename the digital_output, pwm_output, and static_pwm_output config sections to output_pin and move to a new module in the extras/ directory. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* verify_heater: Scale hysteresis duration checkKevin O'Connor2018-03-111-7/+10
| | | | | | | | | | If a heater falls out of the target range, accumulate the temperature differences to determine if an error should be raised. This should make it less likely to report an error for heaters that drift slightly out of range, and it should make error reporting faster for heaters that rapidly fall out of range. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* verify_heater: Change default hysteresis to 10 degreesKevin O'Connor2018-03-111-4/+4
| | | | | | | A default of 4 degrees and 10 seconds may be too aggressive - change the default to 10 degrees and 15 seconds. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* verify_heater: Add initial support for verifying heaters and sensorsKevin O'Connor2018-03-111-0/+22
| | | | | | | Add runtime checks to heaters and temperature sensors to check for possible hardware faults. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* cartesian: Initial support for dual carriagesKevin O'Connor2018-03-091-0/+24
| | | | | | | Add support for additional carriages on cartesian printers. This is used by some printers to handle multiple extruders. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* display: Add initial support for LCD screens attached to an MCUKevin O'Connor2018-03-061-0/+23
| | | | | | | | Add support for displaying basic status information on ST7920 and HD44780 based LCDs that are attached directly to a micro-controller. Signed-off-by: Marcio Teixeira <marcio@alephobjects.com> Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Move description of phase adjusted endstops to config-extra.cfgKevin O'Connor2018-02-271-0/+29
| | | | | | | | Move the description of stepper phase adjusted endstops to a new section in config-extra.cfg. This keeps the main example config file a little more concise. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* config: Reword description of set_position_x paramter in homing_overrideKevin O'Connor2018-02-111-5/+5
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* virtual_sdcard: Initial support for virtual sdcardKevin O'Connor2018-02-111-0/+13
| | | | | | | | Add support for directly printing from a local file on the host. This may be useful if the host cpu is not fast enough to run OctoPrint well. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* fan: Clarify hardware_pwm and allow cycle_time to be set on software pwmKevin O'Connor2018-01-291-8/+7
| | | | | | | | Specify hardware pwm cycle times using the same method as software pwm (in seconds, not clock ticks). Allow the fan code to be configured with an explicit cycle time even when using software pwm. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* homing_override: Allow moves prior to homing an axisKevin O'Connor2018-01-281-0/+8
| | | | | | | Add support for disabling homing checks via the homing_override mechanism. This may be useful to move an axis prior to homing it. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* probe: Create a probe:z_virtual_endstop pinKevin O'Connor2018-01-281-1/+8
| | | | | | | Create a virtual pin that may be used as the z endstop pin on cartesian printers that use the probe in place of a z endstop. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* probe: Support activate/deactivate scripts on each probeKevin O'Connor2018-01-281-0/+9
| | | | | | | | Allow a set of g-code scripts to be run on each probe invocation. This may be useful for probes that need to be setup before they are useful (eg, with servo actuated probes). Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* homing_override: Add basic support for running custom g-code on G28Kevin O'Connor2018-01-281-0/+13
| | | | | | | | Allow users to override the behavior of G28 using a new "homing_override" config section. This may be used on printers that require specific steps during the homing process. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* bed_tilt: Add support for automatic bed tilt move transformationKevin O'Connor2018-01-281-0/+35
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* probe: Initial support for Z-Probe hardwareKevin O'Connor2018-01-281-0/+13
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* extruder: Add support for extruders sharing the same heaterKevin O'Connor2018-01-211-0/+7
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add multi_pin capabilityKevin O'Connor2017-12-181-0/+13
| | | | | | | | Add the ability to alias multiple output pins from a single pin alias. This makes it possible to support some cases where a single logical output is driven by multiple output pins. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add support for output pins set at runtimeKevin O'Connor2017-12-181-19/+52
| | | | | | | Add the ability to define output pins that may be set at runtime with a new SET_PIN extended g-code command. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* stepper: Support for multiple steppers controlling a single axisKevin O'Connor2017-11-181-0/+18
| | | | | | | Allow multiple steppers to be defined for a single cartesian axis. This adds support for dual-z setups. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* fan: Enable heater_fan objects on an MCU shutdown eventKevin O'Connor2017-10-121-1/+6
| | | | | | | Should the MCU go into an error state, set the heater_fan to max_power. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add initial support for servosKevin O'Connor2017-09-201-0/+19
| | | | Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add support for Replicape boardKevin O'Connor2017-09-201-0/+5
| | | | | | | Add support for configuring and controlling the hardware specific to the revision "B3" Replicape board. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* mcu: Initial support for multiple micro-controllersKevin O'Connor2017-09-201-0/+11
| | | | | | | | | Add initial support for controlling multiple independent micro-controllers from a single Klippy host instance. Add basic support for synchronizing the clocks of the additional mcus to the main mcu's clock. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add support for configuring ad5206 digipotsKevin O'Connor2017-08-261-0/+30
| | | | | | | Support an "ad5206" config section so that one can configure the digipots found on Reprap "RAMBo" boards. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* chipmisc: Add support for statically configured output pinsKevin O'Connor2017-08-261-0/+83
Allow digital and PWM output pins to be setup via new config sections. This makes it easier to setup pin configurations. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
generated by cgit v1.2.3-70-g09d2 (git 2.50.1) at 2025-09-02 10:15:33 +0000