diff options
Diffstat (limited to 'src/stm32f0/stm32f0xx_hal_conf.h')
| -rw-r--r-- | src/stm32f0/stm32f0xx_hal_conf.h | 336 |
1 files changed, 0 insertions, 336 deletions
diff --git a/src/stm32f0/stm32f0xx_hal_conf.h b/src/stm32f0/stm32f0xx_hal_conf.h deleted file mode 100644 index 5457b8a1..00000000 --- a/src/stm32f0/stm32f0xx_hal_conf.h +++ /dev/null @@ -1,336 +0,0 @@ -/** -****************************************************************************** -* @file stm32f0xx_hal_conf.h -* @brief HAL configuration file. -****************************************************************************** -* @attention -* -* <h2><center>© COPYRIGHT(c) 2019 STMicroelectronics</center></h2> -* -*Redistribution in source and binary forms, with or without modification, -* are permitted provided that the following conditions are met: -* 1. Redistributions of source code must retain the above copyright notice, -* this list of conditions and the following disclaimer. -* 2. Redistributions in binary form must reproduce the above copyright notice, -* this list of conditions and the following disclaimer in the documentation -* and/or other materials provided with the distribution. -* 3. Neither the name of STMicroelectronics nor the names of its contributors -* may be used to endorse or promote products derived from this software -* without specific prior written permission. -* -* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -*IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE -* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE -* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL -* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR -* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER -* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, -* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE -* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -* -****************************************************************************** -*/ - -/* Define to prevent recursive inclusion -----------------------------------*/ -#ifndef __STM32F0xx_HAL_CONF_H -#define __STM32F0xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ----------------------------------------------------------*/ -/* Exported constants ------------------------------------------------------*/ - -/* ########################## Module Selection ############################ */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -#define HAL_ADC_MODULE_ENABLED -/*#define HAL_CRYP_MODULE_ENABLED */ -#define HAL_CAN_MODULE_ENABLED -/*#define HAL_CEC_MODULE_ENABLED */ -/*#define HAL_COMP_MODULE_ENABLED */ -/*#define HAL_CRC_MODULE_ENABLED */ -/*#define HAL_CRYP_MODULE_ENABLED */ -/*#define HAL_TSC_MODULE_ENABLED */ -/*#define HAL_DAC_MODULE_ENABLED */ -/*#define HAL_I2S_MODULE_ENABLED */ -#define HAL_IWDG_MODULE_ENABLED -/*#define HAL_LCD_MODULE_ENABLED */ -/*#define HAL_LPTIM_MODULE_ENABLED */ -/*#define HAL_RNG_MODULE_ENABLED */ -/*#define HAL_RTC_MODULE_ENABLED */ -#define HAL_SPI_MODULE_ENABLED -#define HAL_TIM_MODULE_ENABLED -#define HAL_UART_MODULE_ENABLED -/*#define HAL_USART_MODULE_ENABLED */ -/*#define HAL_IRDA_MODULE_ENABLED */ -/*#define HAL_SMARTCARD_MODULE_ENABLED */ -/*#define HAL_SMBUS_MODULE_ENABLED */ -/*#define HAL_WWDG_MODULE_ENABLED */ -/*#define HAL_PCD_MODULE_ENABLED */ -/*#define HAL_EXTI_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -#define HAL_DMA_MODULE_ENABLED -#define HAL_FLASH_MODULE_ENABLED -#define HAL_GPIO_MODULE_ENABLED -#define HAL_PWR_MODULE_ENABLED -#define HAL_RCC_MODULE_ENABLED -#define HAL_I2C_MODULE_ENABLED - -/* ########################## HSE/HSI Values adaptation ################### */ -/** -* @brief Adjust the value of External High Speed oscillator (HSE) used\ -* in your application. -* This value is used by the RCC HAL module to compute the system frequency -* (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - /*!< Value of the External oscillator in Hz */ - #define HSE_VALUE ((uint32_t)8000000) -#endif /* HSE_VALUE */ - -/** - * @brief In the following line adjust the External High Speed oscillator\ - * (HSE) Startup - * Timeout value - */ -#if !defined (HSE_STARTUP_TIMEOUT) - /*!< Time out for HSE start up, in ms */ - #define HSE_STARTUP_TIMEOUT ((uint32_t)100) -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - /*!< Value of the Internal oscillator in Hz*/ - #define HSI_VALUE ((uint32_t)8000000) -#endif /* HSI_VALUE */ - -/** - * @brief In the following line adjust the Internal High Speed oscillator \ - * (HSI) Startup - * Timeout value - */ -#if !defined (HSI_STARTUP_TIMEOUT) - #define HSI_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSI startup */ -#endif /* HSI_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator for ADC (HSI14) value. - */ -#if !defined (HSI14_VALUE) -#define HSI14_VALUE ((uint32_t)14000000) - /*!< Value of the Internal High Speed oscillator for ADC in Hz. - The real value may vary depending on the variations - in voltage and temperature. */ -#endif /* HSI14_VALUE */ - -/** - * @brief Internal High Speed oscillator for USB (HSI48) value. - */ -#if !defined (HSI48_VALUE) -#define HSI48_VALUE ((uint32_t)48000000) - /*!< Value of the Internal High Speed oscillator for USB in Hz. - The real value may vary depending on the variations - in voltage and temperature. */ -#endif /* HSI48_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE ((uint32_t)40000) -#endif /* LSI_VALUE */ - /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature. */ -/** - * @brief External Low Speed oscillator (LSI) value. - */ -#if !defined (LSE_VALUE) - /*!< Value of the External Low Speed oscillator in Hz */ - #define LSE_VALUE ((uint32_t)32768) -#endif /* LSE_VALUE */ - -#if !defined (LSE_STARTUP_TIMEOUT) - /*!< Time out for LSE start up, in ms */ - #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) -#endif /* LSE_STARTUP_TIMEOUT */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ######################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ -/*!< tick interrupt priority (lowest by default) */ -#define TICK_INT_PRIORITY ((uint32_t)0) - /* Warning: Must be set to higher priority for HAL_Delay() */ - /* and HAL_GetTick() usage under interrupt context */ -#define USE_RTOS 0 -#define PREFETCH_ENABLE 1 -#define INSTRUCTION_CACHE_ENABLE 0 -#define DATA_CACHE_ENABLE 0 -/* ########################## Assert Selection ############################# */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1U */ - -/* ################## SPI peripheral configuration ######################### */ - -/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver -* Activated: CRC code is present inside driver -* Deactivated: CRC code cleaned from driver -*/ - -#define USE_SPI_CRC 0U - -/* Includes -----------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32f0xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_EXTI_MODULE_ENABLED - #include "stm32f0xx_hal_exti.h" -#endif /* HAL_EXTI_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32f0xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32f0xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32f0xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32f0xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32f0xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED - #include "stm32f0xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_COMP_MODULE_ENABLED - #include "stm32f0xx_hal_comp.h" -#endif /* HAL_COMP_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32f0xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32f0xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32f0xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32f0xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32f0xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32f0xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32f0xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32f0xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32f0xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32f0xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32f0xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_SMBUS_MODULE_ENABLED - #include "stm32f0xx_hal_smbus.h" -#endif /* HAL_SMBUS_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32f0xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32f0xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_TSC_MODULE_ENABLED - #include "stm32f0xx_hal_tsc.h" -#endif /* HAL_TSC_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32f0xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32f0xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32f0xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -/* Exported macro -----------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) \ - ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------ */ - void assert_failed(char* file, uint32_t line); -#else - #define assert_param(expr) ((void)0U) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F0xx_HAL_CONF_H */ - -/********************** (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |