diff options
Diffstat (limited to 'lib/stm32f1/hal/source/stm32f1xx_hal_usart.c')
| -rw-r--r-- | lib/stm32f1/hal/source/stm32f1xx_hal_usart.c | 2799 |
1 files changed, 2799 insertions, 0 deletions
diff --git a/lib/stm32f1/hal/source/stm32f1xx_hal_usart.c b/lib/stm32f1/hal/source/stm32f1xx_hal_usart.c new file mode 100644 index 00000000..1a3ce84f --- /dev/null +++ b/lib/stm32f1/hal/source/stm32f1xx_hal_usart.c @@ -0,0 +1,2799 @@ +/**
+ ******************************************************************************
+ * @file stm32f1xx_hal_usart.c
+ * @author MCD Application Team
+ * @brief USART HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Universal Synchronous/Asynchronous Receiver Transmitter
+ * Peripheral (USART).
+ * + Initialization and de-initialization functions
+ * + IO operation functions
+ * + Peripheral Control functions
+ @verbatim
+ ==============================================================================
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+ The USART HAL driver can be used as follows:
+
+ (#) Declare a USART_HandleTypeDef handle structure (eg. USART_HandleTypeDef husart).
+ (#) Initialize the USART low level resources by implementing the HAL_USART_MspInit() API:
+ (##) Enable the USARTx interface clock.
+ (##) USART pins configuration:
+ (+++) Enable the clock for the USART GPIOs.
+ (+++) Configure the USART pins as alternate function pull-up.
+ (##) NVIC configuration if you need to use interrupt process (HAL_USART_Transmit_IT(),
+ HAL_USART_Receive_IT() and HAL_USART_TransmitReceive_IT() APIs):
+ (+++) Configure the USARTx interrupt priority.
+ (+++) Enable the NVIC USART IRQ handle.
+ (##) DMA Configuration if you need to use DMA process (HAL_USART_Transmit_DMA()
+ HAL_USART_Receive_DMA() and HAL_USART_TransmitReceive_DMA() APIs):
+ (+++) Declare a DMA handle structure for the Tx/Rx channel.
+ (+++) Enable the DMAx interface clock.
+ (+++) Configure the declared DMA handle structure with the required Tx/Rx parameters.
+ (+++) Configure the DMA Tx/Rx channel.
+ (+++) Associate the initialized DMA handle to the USART DMA Tx/Rx handle.
+ (+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx/Rx channel.
+ (+++) Configure the USARTx interrupt priority and enable the NVIC USART IRQ handle
+ (used for last byte sending completion detection in DMA non circular mode)
+
+ (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware
+ flow control and Mode(Receiver/Transmitter) in the husart Init structure.
+
+ (#) Initialize the USART registers by calling the HAL_USART_Init() API:
+ (++) These APIs configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
+ by calling the customized HAL_USART_MspInit(&husart) API.
+
+ -@@- The specific USART interrupts (Transmission complete interrupt,
+ RXNE interrupt and Error Interrupts) will be managed using the macros
+ __HAL_USART_ENABLE_IT() and __HAL_USART_DISABLE_IT() inside the transmit and receive process.
+
+ (#) Three operation modes are available within this driver :
+
+ *** Polling mode IO operation ***
+ =================================
+ [..]
+ (+) Send an amount of data in blocking mode using HAL_USART_Transmit()
+ (+) Receive an amount of data in blocking mode using HAL_USART_Receive()
+
+ *** Interrupt mode IO operation ***
+ ===================================
+ [..]
+ (+) Send an amount of data in non blocking mode using HAL_USART_Transmit_IT()
+ (+) At transmission end of transfer HAL_USART_TxHalfCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_TxCpltCallback
+ (+) Receive an amount of data in non blocking mode using HAL_USART_Receive_IT()
+ (+) At reception end of transfer HAL_USART_RxCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_RxCpltCallback
+ (+) In case of transfer Error, HAL_USART_ErrorCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_USART_ErrorCallback
+
+ *** DMA mode IO operation ***
+ ==============================
+ [..]
+ (+) Send an amount of data in non blocking mode (DMA) using HAL_USART_Transmit_DMA()
+ (+) At transmission end of half transfer HAL_USART_TxHalfCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_TxHalfCpltCallback
+ (+) At transmission end of transfer HAL_USART_TxCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_TxCpltCallback
+ (+) Receive an amount of data in non blocking mode (DMA) using HAL_USART_Receive_DMA()
+ (+) At reception end of half transfer HAL_USART_RxHalfCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_RxHalfCpltCallback
+ (+) At reception end of transfer HAL_USART_RxCpltCallback is executed and user can
+ add his own code by customization of function pointer HAL_USART_RxCpltCallback
+ (+) In case of transfer Error, HAL_USART_ErrorCallback() function is executed and user can
+ add his own code by customization of function pointer HAL_USART_ErrorCallback
+ (+) Pause the DMA Transfer using HAL_USART_DMAPause()
+ (+) Resume the DMA Transfer using HAL_USART_DMAResume()
+ (+) Stop the DMA Transfer using HAL_USART_DMAStop()
+
+ *** USART HAL driver macros list ***
+ =============================================
+ [..]
+ Below the list of most used macros in USART HAL driver.
+
+ (+) __HAL_USART_ENABLE: Enable the USART peripheral
+ (+) __HAL_USART_DISABLE: Disable the USART peripheral
+ (+) __HAL_USART_GET_FLAG : Check whether the specified USART flag is set or not
+ (+) __HAL_USART_CLEAR_FLAG : Clear the specified USART pending flag
+ (+) __HAL_USART_ENABLE_IT: Enable the specified USART interrupt
+ (+) __HAL_USART_DISABLE_IT: Disable the specified USART interrupt
+
+ [..]
+ (@) You can refer to the USART HAL driver header file for more useful macros
+
+ ##### Callback registration #####
+ ==================================
+
+ [..]
+ The compilation define USE_HAL_USART_REGISTER_CALLBACKS when set to 1
+ allows the user to configure dynamically the driver callbacks.
+
+ [..]
+ Use Function @ref HAL_USART_RegisterCallback() to register a user callback.
+ Function @ref HAL_USART_RegisterCallback() allows to register following callbacks:
+ (+) TxHalfCpltCallback : Tx Half Complete Callback.
+ (+) TxCpltCallback : Tx Complete Callback.
+ (+) RxHalfCpltCallback : Rx Half Complete Callback.
+ (+) RxCpltCallback : Rx Complete Callback.
+ (+) TxRxCpltCallback : Tx Rx Complete Callback.
+ (+) ErrorCallback : Error Callback.
+ (+) AbortCpltCallback : Abort Complete Callback.
+ (+) MspInitCallback : USART MspInit.
+ (+) MspDeInitCallback : USART MspDeInit.
+ This function takes as parameters the HAL peripheral handle, the Callback ID
+ and a pointer to the user callback function.
+
+ [..]
+ Use function @ref HAL_USART_UnRegisterCallback() to reset a callback to the default
+ weak (surcharged) function.
+ @ref HAL_USART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ and the Callback ID.
+ This function allows to reset following callbacks:
+ (+) TxHalfCpltCallback : Tx Half Complete Callback.
+ (+) TxCpltCallback : Tx Complete Callback.
+ (+) RxHalfCpltCallback : Rx Half Complete Callback.
+ (+) RxCpltCallback : Rx Complete Callback.
+ (+) TxRxCpltCallback : Tx Rx Complete Callback.
+ (+) ErrorCallback : Error Callback.
+ (+) AbortCpltCallback : Abort Complete Callback.
+ (+) MspInitCallback : USART MspInit.
+ (+) MspDeInitCallback : USART MspDeInit.
+
+ [..]
+ By default, after the @ref HAL_USART_Init() and when the state is HAL_USART_STATE_RESET
+ all callbacks are set to the corresponding weak (surcharged) functions:
+ examples @ref HAL_USART_TxCpltCallback(), @ref HAL_USART_RxHalfCpltCallback().
+ Exception done for MspInit and MspDeInit functions that are respectively
+ reset to the legacy weak (surcharged) functions in the @ref HAL_USART_Init()
+ and @ref HAL_USART_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the @ref HAL_USART_Init() and @ref HAL_USART_DeInit()
+ keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
+
+ [..]
+ Callbacks can be registered/unregistered in HAL_USART_STATE_READY state only.
+ Exception done MspInit/MspDeInit that can be registered/unregistered
+ in HAL_USART_STATE_READY or HAL_USART_STATE_RESET state, thus registered (user)
+ MspInit/DeInit callbacks can be used during the Init/DeInit.
+ In that case first register the MspInit/MspDeInit user callbacks
+ using @ref HAL_USART_RegisterCallback() before calling @ref HAL_USART_DeInit()
+ or @ref HAL_USART_Init() function.
+
+ [..]
+ When The compilation define USE_HAL_USART_REGISTER_CALLBACKS is set to 0 or
+ not defined, the callback registration feature is not available
+ and weak (surcharged) callbacks are used.
+
+ @endverbatim
+ [..]
+ (@) Additionnal remark: If the parity is enabled, then the MSB bit of the data written
+ in the data register is transmitted but is changed by the parity bit.
+ Depending on the frame length defined by the M bit (8-bits or 9-bits),
+ the possible USART frame formats are as listed in the following table:
+ +-------------------------------------------------------------+
+ | M bit | PCE bit | USART frame |
+ |---------------------|---------------------------------------|
+ | 0 | 0 | | SB | 8 bit data | STB | |
+ |---------|-----------|---------------------------------------|
+ | 0 | 1 | | SB | 7 bit data | PB | STB | |
+ |---------|-----------|---------------------------------------|
+ | 1 | 0 | | SB | 9 bit data | STB | |
+ |---------|-----------|---------------------------------------|
+ | 1 | 1 | | SB | 8 bit data | PB | STB | |
+ +-------------------------------------------------------------+
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2016 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup USART USART
+ * @brief HAL USART Synchronous module driver
+ * @{
+ */
+#ifdef HAL_USART_MODULE_ENABLED
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @addtogroup USART_Private_Constants
+ * @{
+ */
+#define DUMMY_DATA 0xFFFFU
+#define USART_TIMEOUT_VALUE 22000U
+/**
+ * @}
+ */
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+/** @addtogroup USART_Private_Functions
+ * @{
+ */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+void USART_InitCallbacksToDefault(USART_HandleTypeDef *husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+static void USART_EndTxTransfer(USART_HandleTypeDef *husart);
+static void USART_EndRxTransfer(USART_HandleTypeDef *husart);
+static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart);
+static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart);
+static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart);
+static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart);
+static void USART_SetConfig(USART_HandleTypeDef *husart);
+static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma);
+static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma);
+static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
+static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma);
+static void USART_DMAError(DMA_HandleTypeDef *hdma);
+static void USART_DMAAbortOnError(DMA_HandleTypeDef *hdma);
+static void USART_DMATxAbortCallback(DMA_HandleTypeDef *hdma);
+static void USART_DMARxAbortCallback(DMA_HandleTypeDef *hdma);
+
+static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout);
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup USART_Exported_Functions USART Exported Functions
+ * @{
+ */
+
+/** @defgroup USART_Exported_Functions_Group1 USART Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Initialization and Configuration functions #####
+ ==============================================================================
+ [..]
+ This subsection provides a set of functions allowing to initialize the USART
+ in asynchronous and in synchronous modes.
+ (+) For the asynchronous mode only these parameters can be configured:
+ (++) Baud Rate
+ (++) Word Length
+ (++) Stop Bit
+ (++) Parity: If the parity is enabled, then the MSB bit of the data written
+ in the data register is transmitted but is changed by the parity bit.
+ Depending on the frame length defined by the M bit (8-bits or 9-bits),
+ please refer to Reference manual for possible USART frame formats.
+ (++) USART polarity
+ (++) USART phase
+ (++) USART LastBit
+ (++) Receiver/transmitter modes
+
+ [..]
+ The HAL_USART_Init() function follows the USART synchronous configuration
+ procedures (details for the procedures are available in reference manuals
+ (RM0008 for STM32F10Xxx MCUs and RM0041 for STM32F100xx MCUs)).
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initialize the USART mode according to the specified
+ * parameters in the USART_InitTypeDef and initialize the associated handle.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart)
+{
+ /* Check the USART handle allocation */
+ if (husart == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_USART_INSTANCE(husart->Instance));
+
+ if (husart->State == HAL_USART_STATE_RESET)
+ {
+ /* Allocate lock resource and initialize it */
+ husart->Lock = HAL_UNLOCKED;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ USART_InitCallbacksToDefault(husart);
+
+ if (husart->MspInitCallback == NULL)
+ {
+ husart->MspInitCallback = HAL_USART_MspInit;
+ }
+
+ /* Init the low level hardware */
+ husart->MspInitCallback(husart);
+#else
+ /* Init the low level hardware : GPIO, CLOCK */
+ HAL_USART_MspInit(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+
+ husart->State = HAL_USART_STATE_BUSY;
+
+ /* Set the USART Communication parameters */
+ USART_SetConfig(husart);
+
+ /* In USART mode, the following bits must be kept cleared:
+ - LINEN bit in the USART_CR2 register
+ - HDSEL, SCEN and IREN bits in the USART_CR3 register */
+ CLEAR_BIT(husart->Instance->CR2, USART_CR2_LINEN);
+ CLEAR_BIT(husart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN));
+
+ /* Enable the Peripheral */
+ __HAL_USART_ENABLE(husart);
+
+ /* Initialize the USART state */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief DeInitializes the USART peripheral.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart)
+{
+ /* Check the USART handle allocation */
+ if (husart == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_USART_INSTANCE(husart->Instance));
+
+ husart->State = HAL_USART_STATE_BUSY;
+
+ /* Disable the Peripheral */
+ __HAL_USART_DISABLE(husart);
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ if (husart->MspDeInitCallback == NULL)
+ {
+ husart->MspDeInitCallback = HAL_USART_MspDeInit;
+ }
+ /* DeInit the low level hardware */
+ husart->MspDeInitCallback(husart);
+#else
+ /* DeInit the low level hardware */
+ HAL_USART_MspDeInit(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief USART MSP Init.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_MspInit(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief USART MSP DeInit.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_MspDeInit(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_MspDeInit could be implemented in the user file
+ */
+}
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+/**
+ * @brief Register a User USART Callback
+ * To be used instead of the weak predefined callback
+ * @param husart usart handle
+ * @param CallbackID ID of the callback to be registered
+ * This parameter can be one of the following values:
+ * @arg @ref HAL_USART_TX_HALFCOMPLETE_CB_ID Tx Half Complete Callback ID
+ * @arg @ref HAL_USART_TX_COMPLETE_CB_ID Tx Complete Callback ID
+ * @arg @ref HAL_USART_RX_HALFCOMPLETE_CB_ID Rx Half Complete Callback ID
+ * @arg @ref HAL_USART_RX_COMPLETE_CB_ID Rx Complete Callback ID
+ * @arg @ref HAL_USART_TX_RX_COMPLETE_CB_ID Rx Complete Callback ID
+ * @arg @ref HAL_USART_ERROR_CB_ID Error Callback ID
+ * @arg @ref HAL_USART_ABORT_COMPLETE_CB_ID Abort Complete Callback ID
+ * @arg @ref HAL_USART_MSPINIT_CB_ID MspInit Callback ID
+ * @arg @ref HAL_USART_MSPDEINIT_CB_ID MspDeInit Callback ID
+ * @param pCallback pointer to the Callback function
+ * @retval HAL status
++ */
+HAL_StatusTypeDef HAL_USART_RegisterCallback(USART_HandleTypeDef *husart, HAL_USART_CallbackIDTypeDef CallbackID, pUSART_CallbackTypeDef pCallback)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ if (pCallback == NULL)
+ {
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ return HAL_ERROR;
+ }
+ /* Process locked */
+ __HAL_LOCK(husart);
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ switch (CallbackID)
+ {
+ case HAL_USART_TX_HALFCOMPLETE_CB_ID :
+ husart->TxHalfCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_TX_COMPLETE_CB_ID :
+ husart->TxCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_RX_HALFCOMPLETE_CB_ID :
+ husart->RxHalfCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_RX_COMPLETE_CB_ID :
+ husart->RxCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_TX_RX_COMPLETE_CB_ID :
+ husart->TxRxCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_ERROR_CB_ID :
+ husart->ErrorCallback = pCallback;
+ break;
+
+ case HAL_USART_ABORT_COMPLETE_CB_ID :
+ husart->AbortCpltCallback = pCallback;
+ break;
+
+ case HAL_USART_MSPINIT_CB_ID :
+ husart->MspInitCallback = pCallback;
+ break;
+
+ case HAL_USART_MSPDEINIT_CB_ID :
+ husart->MspDeInitCallback = pCallback;
+ break;
+
+ default :
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else if (husart->State == HAL_USART_STATE_RESET)
+ {
+ switch (CallbackID)
+ {
+ case HAL_USART_MSPINIT_CB_ID :
+ husart->MspInitCallback = pCallback;
+ break;
+
+ case HAL_USART_MSPDEINIT_CB_ID :
+ husart->MspDeInitCallback = pCallback;
+ break;
+
+ default :
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else
+ {
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ }
+
+ /* Release Lock */
+ __HAL_UNLOCK(husart);
+
+ return status;
+}
+
+/**
+ * @brief Unregister an UART Callback
+ * UART callaback is redirected to the weak predefined callback
+ * @param husart uart handle
+ * @param CallbackID ID of the callback to be unregistered
+ * This parameter can be one of the following values:
+ * @arg @ref HAL_USART_TX_HALFCOMPLETE_CB_ID Tx Half Complete Callback ID
+ * @arg @ref HAL_USART_TX_COMPLETE_CB_ID Tx Complete Callback ID
+ * @arg @ref HAL_USART_RX_HALFCOMPLETE_CB_ID Rx Half Complete Callback ID
+ * @arg @ref HAL_USART_RX_COMPLETE_CB_ID Rx Complete Callback ID
+ * @arg @ref HAL_USART_TX_RX_COMPLETE_CB_ID Rx Complete Callback ID
+ * @arg @ref HAL_USART_ERROR_CB_ID Error Callback ID
+ * @arg @ref HAL_USART_ABORT_COMPLETE_CB_ID Abort Complete Callback ID
+ * @arg @ref HAL_USART_MSPINIT_CB_ID MspInit Callback ID
+ * @arg @ref HAL_USART_MSPDEINIT_CB_ID MspDeInit Callback ID
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_UnRegisterCallback(USART_HandleTypeDef *husart, HAL_USART_CallbackIDTypeDef CallbackID)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ /* Process locked */
+ __HAL_LOCK(husart);
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ switch (CallbackID)
+ {
+ case HAL_USART_TX_HALFCOMPLETE_CB_ID :
+ husart->TxHalfCpltCallback = HAL_USART_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */
+ break;
+
+ case HAL_USART_TX_COMPLETE_CB_ID :
+ husart->TxCpltCallback = HAL_USART_TxCpltCallback; /* Legacy weak TxCpltCallback */
+ break;
+
+ case HAL_USART_RX_HALFCOMPLETE_CB_ID :
+ husart->RxHalfCpltCallback = HAL_USART_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */
+ break;
+
+ case HAL_USART_RX_COMPLETE_CB_ID :
+ husart->RxCpltCallback = HAL_USART_RxCpltCallback; /* Legacy weak RxCpltCallback */
+ break;
+
+ case HAL_USART_TX_RX_COMPLETE_CB_ID :
+ husart->TxRxCpltCallback = HAL_USART_TxRxCpltCallback; /* Legacy weak TxRxCpltCallback */
+ break;
+
+ case HAL_USART_ERROR_CB_ID :
+ husart->ErrorCallback = HAL_USART_ErrorCallback; /* Legacy weak ErrorCallback */
+ break;
+
+ case HAL_USART_ABORT_COMPLETE_CB_ID :
+ husart->AbortCpltCallback = HAL_USART_AbortCpltCallback; /* Legacy weak AbortCpltCallback */
+ break;
+
+ case HAL_USART_MSPINIT_CB_ID :
+ husart->MspInitCallback = HAL_USART_MspInit; /* Legacy weak MspInitCallback */
+ break;
+
+ case HAL_USART_MSPDEINIT_CB_ID :
+ husart->MspDeInitCallback = HAL_USART_MspDeInit; /* Legacy weak MspDeInitCallback */
+ break;
+
+ default :
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else if (husart->State == HAL_USART_STATE_RESET)
+ {
+ switch (CallbackID)
+ {
+ case HAL_USART_MSPINIT_CB_ID :
+ husart->MspInitCallback = HAL_USART_MspInit;
+ break;
+
+ case HAL_USART_MSPDEINIT_CB_ID :
+ husart->MspDeInitCallback = HAL_USART_MspDeInit;
+ break;
+
+ default :
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else
+ {
+ /* Update the error code */
+ husart->ErrorCode |= HAL_USART_ERROR_INVALID_CALLBACK;
+
+ /* Return error status */
+ status = HAL_ERROR;
+ }
+
+ /* Release Lock */
+ __HAL_UNLOCK(husart);
+
+ return status;
+}
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Exported_Functions_Group2 IO operation functions
+ * @brief USART Transmit and Receive functions
+ *
+@verbatim
+ ==============================================================================
+ ##### IO operation functions #####
+ ==============================================================================
+ [..]
+ This subsection provides a set of functions allowing to manage the USART synchronous
+ data transfers.
+
+ [..]
+ The USART supports master mode only: it cannot receive or send data related to an input
+ clock (SCLK is always an output).
+
+ (#) There are two modes of transfer:
+ (++) Blocking mode: The communication is performed in polling mode.
+ The HAL status of all data processing is returned by the same function
+ after finishing transfer.
+ (++) No-Blocking mode: The communication is performed using Interrupts
+ or DMA, These API's return the HAL status.
+ The end of the data processing will be indicated through the
+ dedicated USART IRQ when using Interrupt mode or the DMA IRQ when
+ using DMA mode.
+ The HAL_USART_TxCpltCallback(), HAL_USART_RxCpltCallback() and HAL_USART_TxRxCpltCallback()
+ user callbacks
+ will be executed respectively at the end of the transmit or Receive process
+ The HAL_USART_ErrorCallback() user callback will be executed when a communication
+ error is detected
+
+ (#) Blocking mode APIs are :
+ (++) HAL_USART_Transmit() in simplex mode
+ (++) HAL_USART_Receive() in full duplex receive only
+ (++) HAL_USART_TransmitReceive() in full duplex mode
+
+ (#) Non Blocking mode APIs with Interrupt are :
+ (++) HAL_USART_Transmit_IT()in simplex mode
+ (++) HAL_USART_Receive_IT() in full duplex receive only
+ (++) HAL_USART_TransmitReceive_IT() in full duplex mode
+ (++) HAL_USART_IRQHandler()
+
+ (#) Non Blocking mode functions with DMA are :
+ (++) HAL_USART_Transmit_DMA()in simplex mode
+ (++) HAL_USART_Receive_DMA() in full duplex receive only
+ (++) HAL_USART_TransmitReceive_DMA() in full duplex mode
+ (++) HAL_USART_DMAPause()
+ (++) HAL_USART_DMAResume()
+ (++) HAL_USART_DMAStop()
+
+ (#) A set of Transfer Complete Callbacks are provided in non Blocking mode:
+ (++) HAL_USART_TxHalfCpltCallback()
+ (++) HAL_USART_TxCpltCallback()
+ (++) HAL_USART_RxHalfCpltCallback()
+ (++) HAL_USART_RxCpltCallback()
+ (++) HAL_USART_ErrorCallback()
+ (++) HAL_USART_TxRxCpltCallback()
+
+ (#) Non-Blocking mode transfers could be aborted using Abort API's :
+ (++) HAL_USART_Abort()
+ (++) HAL_USART_Abort_IT()
+
+ (#) For Abort services based on interrupts (HAL_USART_Abort_IT), a Abort Complete Callbacks is provided:
+ (++) HAL_USART_AbortCpltCallback()
+
+ (#) In Non-Blocking mode transfers, possible errors are split into 2 categories.
+ Errors are handled as follows :
+ (++) Error is considered as Recoverable and non blocking : Transfer could go till end, but error severity is
+ to be evaluated by user : this concerns Frame Error, Parity Error or Noise Error in Interrupt mode reception .
+ Received character is then retrieved and stored in Rx buffer, Error code is set to allow user to identify error type,
+ and HAL_USART_ErrorCallback() user callback is executed. Transfer is kept ongoing on USART side.
+ If user wants to abort it, Abort services should be called by user.
+ (++) Error is considered as Blocking : Transfer could not be completed properly and is aborted.
+ This concerns Overrun Error In Interrupt mode reception and all errors in DMA mode.
+ Error code is set to allow user to identify error type, and HAL_USART_ErrorCallback() user callback is executed.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Simplex Send an amount of data in blocking mode.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 provided through pTxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be sent.
+ * @param Timeout Timeout duration.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout)
+{
+ uint16_t *tmp;
+ uint32_t tickstart = 0U;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_TX;
+
+ /* Init tickstart for timeout management */
+ tickstart = HAL_GetTick();
+
+ husart->TxXferSize = Size;
+ husart->TxXferCount = Size;
+ while (husart->TxXferCount > 0U)
+ {
+ husart->TxXferCount--;
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ /* Wait for TC flag in order to write data in DR */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ tmp = (uint16_t *) pTxData;
+ husart->Instance->DR = (*tmp & (uint16_t)0x01FF);
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ pTxData += 2U;
+ }
+ else
+ {
+ pTxData += 1U;
+ }
+ }
+ else
+ {
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ husart->Instance->DR = (*pTxData++ & (uint8_t)0xFF);
+ }
+ }
+
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Receive an amount of data in blocking mode.
+ * @note To receive synchronous data, dummy data are simultaneously transmitted.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the received data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 available through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pRxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be received.
+ * @param Timeout Timeout duration.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout)
+{
+ uint16_t *tmp;
+ uint32_t tickstart = 0U;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_RX;
+
+ /* Init tickstart for timeout management */
+ tickstart = HAL_GetTick();
+
+ husart->RxXferSize = Size;
+ husart->RxXferCount = Size;
+ /* Check the remain data to be received */
+ while (husart->RxXferCount > 0U)
+ {
+ husart->RxXferCount--;
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ /* Wait until TXE flag is set to send dummy byte in order to generate the clock for the slave to send data */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ /* Send dummy byte in order to generate clock */
+ husart->Instance->DR = (DUMMY_DATA & (uint16_t)0x01FF);
+
+ /* Wait for RXNE Flag */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ tmp = (uint16_t *) pRxData ;
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x01FF);
+ pRxData += 2U;
+ }
+ else
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x00FF);
+ pRxData += 1U;
+ }
+ }
+ else
+ {
+ /* Wait until TXE flag is set to send dummy byte in order to generate the clock for the slave to send data */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+
+ /* Send Dummy Byte in order to generate clock */
+ husart->Instance->DR = (DUMMY_DATA & (uint16_t)0x00FF);
+
+ /* Wait until RXNE flag is set to receive the byte */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ /* Receive data */
+ *pRxData++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x00FF);
+ }
+ else
+ {
+ /* Receive data */
+ *pRxData++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x007F);
+ }
+
+ }
+ }
+
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Send and Receive an amount of data in full-duplex mode (blocking mode).
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data and the received data are handled as sets of u16. In this case, Size must indicate the number
+ * of u16 available through pTxData and through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to TX data buffer (u8 or u16 data elements).
+ * @param pRxData Pointer to RX data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be sent (same amount to be received).
+ * @param Timeout Timeout duration
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout)
+{
+ uint16_t *tmp;
+ uint32_t tickstart = 0U;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_RX;
+
+ /* Init tickstart for timeout management */
+ tickstart = HAL_GetTick();
+
+ husart->RxXferSize = Size;
+ husart->TxXferSize = Size;
+ husart->TxXferCount = Size;
+ husart->RxXferCount = Size;
+
+ /* Check the remain data to be received */
+ while (husart->TxXferCount > 0U)
+ {
+ husart->TxXferCount--;
+ husart->RxXferCount--;
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ /* Wait for TC flag in order to write data in DR */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ tmp = (uint16_t *) pTxData;
+ husart->Instance->DR = (*tmp & (uint16_t)0x01FF);
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ pTxData += 2U;
+ }
+ else
+ {
+ pTxData += 1U;
+ }
+
+ /* Wait for RXNE Flag */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ tmp = (uint16_t *) pRxData ;
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x01FF);
+ pRxData += 2U;
+ }
+ else
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x00FF);
+ pRxData += 1U;
+ }
+ }
+ else
+ {
+ /* Wait for TC flag in order to write data in DR */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ husart->Instance->DR = (*pTxData++ & (uint8_t)0x00FF);
+
+ /* Wait for RXNE Flag */
+ if (USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
+ {
+ return HAL_TIMEOUT;
+ }
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ /* Receive data */
+ *pRxData++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x00FF);
+ }
+ else
+ {
+ /* Receive data */
+ *pRxData++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x007F);
+ }
+ }
+ }
+
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Simplex Send an amount of data in non-blocking mode.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 provided through pTxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be sent.
+ * @retval HAL status
+ * @note The USART errors are not managed to avoid the overrun error.
+ */
+HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size)
+{
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pTxBuffPtr = pTxData;
+ husart->TxXferSize = Size;
+ husart->TxXferCount = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_TX;
+
+ /* The USART Error Interrupts: (Frame error, Noise error, Overrun error)
+ are not managed by the USART transmit process to avoid the overrun interrupt
+ when the USART mode is configured for transmit and receive "USART_MODE_TX_RX"
+ to benefit for the frame error and noise interrupts the USART mode should be
+ configured only for transmit "USART_MODE_TX"
+ The __HAL_USART_ENABLE_IT(husart, USART_IT_ERR) can be used to enable the Frame error,
+ Noise error interrupt */
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the USART Transmit Data Register Empty Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_TXEIE);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Simplex Receive an amount of data in non-blocking mode.
+ * @note To receive synchronous data, dummy data are simultaneously transmitted.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the received data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 available through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pRxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be received.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size)
+{
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pRxBuffPtr = pRxData;
+ husart->RxXferSize = Size;
+ husart->RxXferCount = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_RX;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the USART Parity Error and Data Register not empty Interrupts */
+ SET_BIT(husart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE);
+
+ /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ SET_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Send dummy byte in order to generate the clock for the slave to send data */
+ husart->Instance->DR = (DUMMY_DATA & (uint16_t)0x01FF);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Send and Receive an amount of data in full-duplex mode (non-blocking).
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data and the received data are handled as sets of u16. In this case, Size must indicate the number
+ * of u16 available through pTxData and through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to TX data buffer (u8 or u16 data elements).
+ * @param pRxData Pointer to RX data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be sent (same amount to be received).
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size)
+{
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pRxBuffPtr = pRxData;
+ husart->RxXferSize = Size;
+ husart->RxXferCount = Size;
+ husart->pTxBuffPtr = pTxData;
+ husart->TxXferSize = Size;
+ husart->TxXferCount = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_TX_RX;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the USART Data Register not empty Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_RXNEIE);
+
+ /* Enable the USART Parity Error Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ SET_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Enable the USART Transmit Data Register Empty Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_TXEIE);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Simplex Send an amount of data in DMA mode.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 provided through pTxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be sent.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size)
+{
+ uint32_t *tmp;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pTxBuffPtr = pTxData;
+ husart->TxXferSize = Size;
+ husart->TxXferCount = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_TX;
+
+ /* Set the USART DMA transfer complete callback */
+ husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt;
+
+ /* Set the USART DMA Half transfer complete callback */
+ husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt;
+
+ /* Set the DMA error callback */
+ husart->hdmatx->XferErrorCallback = USART_DMAError;
+
+ /* Set the DMA abort callback */
+ husart->hdmatx->XferAbortCallback = NULL;
+
+ /* Enable the USART transmit DMA channel */
+ tmp = (uint32_t *)&pTxData;
+ HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t *)tmp, (uint32_t)&husart->Instance->DR, Size);
+
+ /* Clear the TC flag in the SR register by writing 0 to it */
+ __HAL_USART_CLEAR_FLAG(husart, USART_FLAG_TC);
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the DMA transfer for transmit request by setting the DMAT bit
+ in the USART CR3 register */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Receive an amount of data in DMA mode.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the received data is handled as a set of u16. In this case, Size must indicate the number
+ * of u16 available through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pRxData Pointer to data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be received.
+ * @retval HAL status
+ * @note The USART DMA transmit channel must be configured in order to generate the clock for the slave.
+ * @note When the USART parity is enabled (PCE = 1) the data received contain the parity bit.
+ */
+HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size)
+{
+ uint32_t *tmp;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pRxBuffPtr = pRxData;
+ husart->RxXferSize = Size;
+ husart->pTxBuffPtr = pRxData;
+ husart->TxXferSize = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_RX;
+
+ /* Set the USART DMA Rx transfer complete callback */
+ husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt;
+
+ /* Set the USART DMA Half transfer complete callback */
+ husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt;
+
+ /* Set the USART DMA Rx transfer error callback */
+ husart->hdmarx->XferErrorCallback = USART_DMAError;
+
+ /* Set the DMA abort callback */
+ husart->hdmarx->XferAbortCallback = NULL;
+
+ /* Set the USART Tx DMA transfer complete callback as NULL because the communication closing
+ is performed in DMA reception complete callback */
+ husart->hdmatx->XferHalfCpltCallback = NULL;
+ husart->hdmatx->XferCpltCallback = NULL;
+
+ /* Set the DMA error callback */
+ husart->hdmatx->XferErrorCallback = USART_DMAError;
+
+ /* Set the DMA AbortCpltCallback */
+ husart->hdmatx->XferAbortCallback = NULL;
+
+ /* Enable the USART receive DMA channel */
+ tmp = (uint32_t *)&pRxData;
+ HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->DR, *(uint32_t *)tmp, Size);
+
+ /* Enable the USART transmit DMA channel: the transmit channel is used in order
+ to generate in the non-blocking mode the clock to the slave device,
+ this mode isn't a simplex receive mode but a full-duplex receive one */
+ HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t *)tmp, (uint32_t)&husart->Instance->DR, Size);
+
+ /* Clear the Overrun flag just before enabling the DMA Rx request: mandatory for the second transfer */
+ __HAL_USART_CLEAR_OREFLAG(husart);
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the USART Parity Error Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ SET_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Enable the DMA transfer for the receiver request by setting the DMAR bit
+ in the USART CR3 register */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+
+ /* Enable the DMA transfer for transmit request by setting the DMAT bit
+ in the USART CR3 register */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Transmit Receive an amount of data in DMA mode.
+ * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01),
+ * the sent data and the received data are handled as sets of u16. In this case, Size must indicate the number
+ * of u16 available through pTxData and through pRxData.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param pTxData Pointer to TX data buffer (u8 or u16 data elements).
+ * @param pRxData Pointer to RX data buffer (u8 or u16 data elements).
+ * @param Size Amount of data elements (u8 or u16) to be received/sent.
+ * @note When the USART parity is enabled (PCE = 1) the data received contain the parity bit.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size)
+{
+ uint32_t *tmp;
+
+ if (husart->State == HAL_USART_STATE_READY)
+ {
+ if ((pTxData == NULL) || (pRxData == NULL) || (Size == 0))
+ {
+ return HAL_ERROR;
+ }
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ husart->pRxBuffPtr = pRxData;
+ husart->RxXferSize = Size;
+ husart->pTxBuffPtr = pTxData;
+ husart->TxXferSize = Size;
+
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ husart->State = HAL_USART_STATE_BUSY_TX_RX;
+
+ /* Set the USART DMA Rx transfer complete callback */
+ husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt;
+
+ /* Set the USART DMA Half transfer complete callback */
+ husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt;
+
+ /* Set the USART DMA Tx transfer complete callback */
+ husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt;
+
+ /* Set the USART DMA Half transfer complete callback */
+ husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt;
+
+ /* Set the USART DMA Tx transfer error callback */
+ husart->hdmatx->XferErrorCallback = USART_DMAError;
+
+ /* Set the USART DMA Rx transfer error callback */
+ husart->hdmarx->XferErrorCallback = USART_DMAError;
+
+ /* Set the DMA abort callback */
+ husart->hdmarx->XferAbortCallback = NULL;
+
+ /* Enable the USART receive DMA channel */
+ tmp = (uint32_t *)&pRxData;
+ HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->DR, *(uint32_t *)tmp, Size);
+
+ /* Enable the USART transmit DMA channel */
+ tmp = (uint32_t *)&pTxData;
+ HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t *)tmp, (uint32_t)&husart->Instance->DR, Size);
+
+ /* Clear the TC flag in the SR register by writing 0 to it */
+ __HAL_USART_CLEAR_FLAG(husart, USART_FLAG_TC);
+
+ /* Clear the Overrun flag: mandatory for the second transfer in circular mode */
+ __HAL_USART_CLEAR_OREFLAG(husart);
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ /* Enable the USART Parity Error Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ SET_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Enable the DMA transfer for the receiver request by setting the DMAR bit
+ in the USART CR3 register */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+
+ /* Enable the DMA transfer for transmit request by setting the DMAT bit
+ in the USART CR3 register */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Pauses the DMA Transfer.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart)
+{
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ /* Disable the USART DMA Tx request */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Resumes the DMA Transfer.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart)
+{
+ /* Process Locked */
+ __HAL_LOCK(husart);
+
+ /* Enable the USART DMA Tx request */
+ SET_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the DMA Transfer.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart)
+{
+ uint32_t dmarequest = 0x00U;
+ /* The Lock is not implemented on this API to allow the user application
+ to call the HAL USART API under callbacks HAL_USART_TxCpltCallback() / HAL_USART_RxCpltCallback():
+ when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated
+ and the correspond call back is executed HAL_USART_TxCpltCallback() / HAL_USART_RxCpltCallback()
+ */
+
+ /* Stop USART DMA Tx request if ongoing */
+ dmarequest = HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT);
+ if ((husart->State == HAL_USART_STATE_BUSY_TX) && dmarequest)
+ {
+ USART_EndTxTransfer(husart);
+
+ /* Abort the USART DMA Tx channel */
+ if (husart->hdmatx != NULL)
+ {
+ HAL_DMA_Abort(husart->hdmatx);
+ }
+
+ /* Disable the USART Tx DMA request */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+ }
+
+ /* Stop USART DMA Rx request if ongoing */
+ dmarequest = HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR);
+ if ((husart->State == HAL_USART_STATE_BUSY_RX) && dmarequest)
+ {
+ USART_EndRxTransfer(husart);
+
+ /* Abort the USART DMA Rx channel */
+ if (husart->hdmarx != NULL)
+ {
+ HAL_DMA_Abort(husart->hdmarx);
+ }
+
+ /* Disable the USART Rx DMA request */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Abort ongoing transfer (blocking mode).
+ * @param husart USART handle.
+ * @note This procedure could be used for aborting any ongoing transfer (either Tx or Rx,
+ * as described by TransferType parameter) started in Interrupt or DMA mode.
+ * This procedure performs following operations :
+ * - Disable PPP Interrupts (depending of transfer direction)
+ * - Disable the DMA transfer in the peripheral register (if enabled)
+ * - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode)
+ * - Set handle State to READY
+ * @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed.
+ * @retval HAL status
+*/
+HAL_StatusTypeDef HAL_USART_Abort(USART_HandleTypeDef *husart)
+{
+ /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
+ CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE));
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Disable the USART DMA Tx request if enabled */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT))
+ {
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ /* Abort the USART DMA Tx channel : use blocking DMA Abort API (no callback) */
+ if (husart->hdmatx != NULL)
+ {
+ /* Set the USART DMA Abort callback to Null.
+ No call back execution at end of DMA abort procedure */
+ husart->hdmatx->XferAbortCallback = NULL;
+
+ HAL_DMA_Abort(husart->hdmatx);
+ }
+ }
+
+ /* Disable the USART DMA Rx request if enabled */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR))
+ {
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+
+ /* Abort the USART DMA Rx channel : use blocking DMA Abort API (no callback) */
+ if (husart->hdmarx != NULL)
+ {
+ /* Set the USART DMA Abort callback to Null.
+ No call back execution at end of DMA abort procedure */
+ husart->hdmarx->XferAbortCallback = NULL;
+
+ HAL_DMA_Abort(husart->hdmarx);
+ }
+ }
+
+ /* Reset Tx and Rx transfer counters */
+ husart->TxXferCount = 0x00U;
+ husart->RxXferCount = 0x00U;
+
+ /* Restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Reset Handle ErrorCode to No Error */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Abort ongoing transfer (Interrupt mode).
+ * @param husart USART handle.
+ * @note This procedure could be used for aborting any ongoing transfer (either Tx or Rx,
+ * as described by TransferType parameter) started in Interrupt or DMA mode.
+ * This procedure performs following operations :
+ * - Disable PPP Interrupts (depending of transfer direction)
+ * - Disable the DMA transfer in the peripheral register (if enabled)
+ * - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode)
+ * - Set handle State to READY
+ * - At abort completion, call user abort complete callback
+ * @note This procedure is executed in Interrupt mode, meaning that abort procedure could be
+ * considered as completed only when user abort complete callback is executed (not when exiting function).
+ * @retval HAL status
+*/
+HAL_StatusTypeDef HAL_USART_Abort_IT(USART_HandleTypeDef *husart)
+{
+ uint32_t AbortCplt = 0x01U;
+
+ /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
+ CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE));
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* If DMA Tx and/or DMA Rx Handles are associated to USART Handle, DMA Abort complete callbacks should be initialised
+ before any call to DMA Abort functions */
+ /* DMA Tx Handle is valid */
+ if (husart->hdmatx != NULL)
+ {
+ /* Set DMA Abort Complete callback if USART DMA Tx request if enabled.
+ Otherwise, set it to NULL */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT))
+ {
+ husart->hdmatx->XferAbortCallback = USART_DMATxAbortCallback;
+ }
+ else
+ {
+ husart->hdmatx->XferAbortCallback = NULL;
+ }
+ }
+ /* DMA Rx Handle is valid */
+ if (husart->hdmarx != NULL)
+ {
+ /* Set DMA Abort Complete callback if USART DMA Rx request if enabled.
+ Otherwise, set it to NULL */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR))
+ {
+ husart->hdmarx->XferAbortCallback = USART_DMARxAbortCallback;
+ }
+ else
+ {
+ husart->hdmarx->XferAbortCallback = NULL;
+ }
+ }
+
+ /* Disable the USART DMA Tx request if enabled */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT))
+ {
+ /* Disable DMA Tx at USART level */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ /* Abort the USART DMA Tx channel : use non blocking DMA Abort API (callback) */
+ if (husart->hdmatx != NULL)
+ {
+ /* USART Tx DMA Abort callback has already been initialised :
+ will lead to call HAL_USART_AbortCpltCallback() at end of DMA abort procedure */
+
+ /* Abort DMA TX */
+ if (HAL_DMA_Abort_IT(husart->hdmatx) != HAL_OK)
+ {
+ husart->hdmatx->XferAbortCallback = NULL;
+ }
+ else
+ {
+ AbortCplt = 0x00U;
+ }
+ }
+ }
+
+ /* Disable the USART DMA Rx request if enabled */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR))
+ {
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+
+ /* Abort the USART DMA Rx channel : use non blocking DMA Abort API (callback) */
+ if (husart->hdmarx != NULL)
+ {
+ /* USART Rx DMA Abort callback has already been initialised :
+ will lead to call HAL_USART_AbortCpltCallback() at end of DMA abort procedure */
+
+ /* Abort DMA RX */
+ if (HAL_DMA_Abort_IT(husart->hdmarx) != HAL_OK)
+ {
+ husart->hdmarx->XferAbortCallback = NULL;
+ AbortCplt = 0x01U;
+ }
+ else
+ {
+ AbortCplt = 0x00U;
+ }
+ }
+ }
+
+ /* if no DMA abort complete callback execution is required => call user Abort Complete callback */
+ if (AbortCplt == 0x01U)
+ {
+ /* Reset Tx and Rx transfer counters */
+ husart->TxXferCount = 0x00U;
+ husart->RxXferCount = 0x00U;
+
+ /* Reset errorCode */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+
+ /* Restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+
+ /* As no DMA to be aborted, call directly user Abort complete callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Abort Complete Callback */
+ husart->AbortCpltCallback(husart);
+#else
+ /* Call legacy weak Abort Complete Callback */
+ HAL_USART_AbortCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief This function handles USART interrupt request.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+void HAL_USART_IRQHandler(USART_HandleTypeDef *husart)
+{
+ uint32_t isrflags = READ_REG(husart->Instance->SR);
+ uint32_t cr1its = READ_REG(husart->Instance->CR1);
+ uint32_t cr3its = READ_REG(husart->Instance->CR3);
+ uint32_t errorflags = 0x00U;
+ uint32_t dmarequest = 0x00U;
+
+ /* If no error occurs */
+ errorflags = (isrflags & (uint32_t)(USART_SR_PE | USART_SR_FE | USART_SR_ORE | USART_SR_NE));
+ if (errorflags == RESET)
+ {
+ /* USART in mode Receiver -------------------------------------------------*/
+ if (((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
+ {
+ if (husart->State == HAL_USART_STATE_BUSY_RX)
+ {
+ USART_Receive_IT(husart);
+ }
+ else
+ {
+ USART_TransmitReceive_IT(husart);
+ }
+ return;
+ }
+ }
+ /* If some errors occur */
+ if ((errorflags != RESET) && (((cr3its & USART_CR3_EIE) != RESET) || ((cr1its & (USART_CR1_RXNEIE | USART_CR1_PEIE)) != RESET)))
+ {
+ /* USART parity error interrupt occurred ----------------------------------*/
+ if (((isrflags & USART_SR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET))
+ {
+ husart->ErrorCode |= HAL_USART_ERROR_PE;
+ }
+
+ /* USART noise error interrupt occurred --------------------------------*/
+ if (((isrflags & USART_SR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
+ {
+ husart->ErrorCode |= HAL_USART_ERROR_NE;
+ }
+
+ /* USART frame error interrupt occurred --------------------------------*/
+ if (((isrflags & USART_SR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
+ {
+ husart->ErrorCode |= HAL_USART_ERROR_FE;
+ }
+
+ /* USART Over-Run interrupt occurred -----------------------------------*/
+ if (((isrflags & USART_SR_ORE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
+ {
+ husart->ErrorCode |= HAL_USART_ERROR_ORE;
+ }
+
+ if (husart->ErrorCode != HAL_USART_ERROR_NONE)
+ {
+ /* USART in mode Receiver -----------------------------------------------*/
+ if (((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
+ {
+ if (husart->State == HAL_USART_STATE_BUSY_RX)
+ {
+ USART_Receive_IT(husart);
+ }
+ else
+ {
+ USART_TransmitReceive_IT(husart);
+ }
+ }
+ /* If Overrun error occurs, or if any error occurs in DMA mode reception,
+ consider error as blocking */
+ dmarequest = HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR);
+ if (((husart->ErrorCode & HAL_USART_ERROR_ORE) != RESET) || dmarequest)
+ {
+ /* Set the USART state ready to be able to start again the process,
+ Disable Rx Interrupts, and disable Rx DMA request, if ongoing */
+ USART_EndRxTransfer(husart);
+
+ /* Disable the USART DMA Rx request if enabled */
+ if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR))
+ {
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+
+ /* Abort the USART DMA Rx channel */
+ if (husart->hdmarx != NULL)
+ {
+ /* Set the USART DMA Abort callback :
+ will lead to call HAL_USART_ErrorCallback() at end of DMA abort procedure */
+ husart->hdmarx->XferAbortCallback = USART_DMAAbortOnError;
+
+ if (HAL_DMA_Abort_IT(husart->hdmarx) != HAL_OK)
+ {
+ /* Call Directly XferAbortCallback function in case of error */
+ husart->hdmarx->XferAbortCallback(husart->hdmarx);
+ }
+ }
+ else
+ {
+ /* Call user error callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Error Callback */
+ husart->ErrorCallback(husart);
+#else
+ /* Call legacy weak Error Callback */
+ HAL_USART_ErrorCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ }
+ else
+ {
+ /* Call user error callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Error Callback */
+ husart->ErrorCallback(husart);
+#else
+ /* Call legacy weak Error Callback */
+ HAL_USART_ErrorCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ }
+ else
+ {
+ /* Call user error callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Error Callback */
+ husart->ErrorCallback(husart);
+#else
+ /* Call legacy weak Error Callback */
+ HAL_USART_ErrorCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+ }
+ }
+ return;
+ }
+
+ /* USART in mode Transmitter -----------------------------------------------*/
+ if (((isrflags & USART_SR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET))
+ {
+ if (husart->State == HAL_USART_STATE_BUSY_TX)
+ {
+ USART_Transmit_IT(husart);
+ }
+ else
+ {
+ USART_TransmitReceive_IT(husart);
+ }
+ return;
+ }
+
+ /* USART in mode Transmitter (transmission end) ----------------------------*/
+ if (((isrflags & USART_SR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET))
+ {
+ USART_EndTransmit_IT(husart);
+ return;
+ }
+}
+
+/**
+ * @brief Tx Transfer completed callbacks.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_TxCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Tx Half Transfer completed callbacks.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_TxHalfCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Rx Transfer completed callbacks.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_RxCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Rx Half Transfer completed callbacks.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_RxHalfCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Tx/Rx Transfers completed callback for the non-blocking process.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_TxRxCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief USART error callbacks.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+__weak void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+ /* NOTE: This function should not be modified, when the callback is needed,
+ the HAL_USART_ErrorCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief USART Abort Complete callback.
+ * @param husart USART handle.
+ * @retval None
+ */
+__weak void HAL_USART_AbortCpltCallback(USART_HandleTypeDef *husart)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(husart);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_USART_AbortCpltCallback can be implemented in the user file.
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Exported_Functions_Group3 Peripheral State and Errors functions
+ * @brief USART State and Errors functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Peripheral State and Errors functions #####
+ ==============================================================================
+ [..]
+ This subsection provides a set of functions allowing to return the State of
+ USART communication
+ process, return Peripheral Errors occurred during communication process
+ (+) HAL_USART_GetState() API can be helpful to check in run-time the state
+ of the USART peripheral.
+ (+) HAL_USART_GetError() check in run-time errors that could be occurred during
+ communication.
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Returns the USART state.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL state
+ */
+HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart)
+{
+ return husart->State;
+}
+
+/**
+ * @brief Return the USART error code
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART.
+ * @retval USART Error Code
+ */
+uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart)
+{
+ return husart->ErrorCode;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Private_Functions USART Private Functions
+ * @{
+ */
+
+/**
+ * @brief Initialize the callbacks to their default values.
+ * @param husart USART handle.
+ * @retval none
+ */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+void USART_InitCallbacksToDefault(USART_HandleTypeDef *husart)
+{
+ /* Init the USART Callback settings */
+ husart->TxHalfCpltCallback = HAL_USART_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */
+ husart->TxCpltCallback = HAL_USART_TxCpltCallback; /* Legacy weak TxCpltCallback */
+ husart->RxHalfCpltCallback = HAL_USART_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */
+ husart->RxCpltCallback = HAL_USART_RxCpltCallback; /* Legacy weak RxCpltCallback */
+ husart->TxRxCpltCallback = HAL_USART_TxRxCpltCallback; /* Legacy weak TxRxCpltCallback */
+ husart->ErrorCallback = HAL_USART_ErrorCallback; /* Legacy weak ErrorCallback */
+ husart->AbortCpltCallback = HAL_USART_AbortCpltCallback; /* Legacy weak AbortCpltCallback */
+}
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+/**
+ * @brief DMA USART transmit process complete callback.
+ * @param hdma Pointer to a DMA_HandleTypeDef structure that contains
+ * the configuration information for the specified DMA module.
+ * @retval None
+ */
+static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+ /* DMA Normal mode */
+ if ((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+ {
+ husart->TxXferCount = 0U;
+ if (husart->State == HAL_USART_STATE_BUSY_TX)
+ {
+ /* Disable the DMA transfer for transmit request by resetting the DMAT bit
+ in the USART CR3 register */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ /* Enable the USART Transmit Complete Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_TCIE);
+ }
+ }
+ /* DMA Circular mode */
+ else
+ {
+ if (husart->State == HAL_USART_STATE_BUSY_TX)
+ {
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Complete Callback */
+ husart->TxCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Complete Callback */
+ HAL_USART_TxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ }
+}
+
+/**
+ * @brief DMA USART transmit process half complete callback
+ * @param hdma Pointer to a DMA_HandleTypeDef structure that contains
+ * the configuration information for the specified DMA module.
+ * @retval None
+ */
+static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Half Complete Callback */
+ husart->TxHalfCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Half Complete Callback */
+ HAL_USART_TxHalfCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief DMA USART receive process complete callback.
+ * @param hdma Pointer to a DMA_HandleTypeDef structure that contains
+ * the configuration information for the specified DMA module.
+ * @retval None
+ */
+static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+ /* DMA Normal mode */
+ if ((hdma->Instance->CCR & DMA_CCR_CIRC) == 0U)
+ {
+ husart->RxXferCount = 0x00U;
+
+ /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* Disable the DMA transfer for the Transmit/receiver request by clearing the DMAT/DMAR bit
+ in the USART CR3 register */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR);
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT);
+
+ husart->State = HAL_USART_STATE_READY;
+
+ /* The USART state is HAL_USART_STATE_BUSY_RX */
+ if (husart->State == HAL_USART_STATE_BUSY_RX)
+ {
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Rx Complete Callback */
+ husart->RxCpltCallback(husart);
+#else
+ /* Call legacy weak Rx Complete Callback */
+ HAL_USART_RxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ /* The USART state is HAL_USART_STATE_BUSY_TX_RX */
+ else
+ {
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Rx Complete Callback */
+ husart->TxRxCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Rx Complete Callback */
+ HAL_USART_TxRxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ }
+ /* DMA circular mode */
+ else
+ {
+ if (husart->State == HAL_USART_STATE_BUSY_RX)
+ {
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Rx Complete Callback */
+ husart->RxCpltCallback(husart);
+#else
+ /* Call legacy weak Rx Complete Callback */
+ HAL_USART_RxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ /* The USART state is HAL_USART_STATE_BUSY_TX_RX */
+ else
+ {
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Rx Complete Callback */
+ husart->TxRxCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Rx Complete Callback */
+ HAL_USART_TxRxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+ }
+ }
+}
+
+/**
+ * @brief DMA USART receive process half complete callback
+ * @param hdma Pointer to a DMA_HandleTypeDef structure that contains
+ * the configuration information for the specified DMA module.
+ * @retval None
+ */
+static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Rx Half Complete Callback */
+ husart->RxHalfCpltCallback(husart);
+#else
+ /* Call legacy weak Rx Half Complete Callback */
+ HAL_USART_RxHalfCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief DMA USART communication error callback.
+ * @param hdma Pointer to a DMA_HandleTypeDef structure that contains
+ * the configuration information for the specified DMA module.
+ * @retval None
+ */
+static void USART_DMAError(DMA_HandleTypeDef *hdma)
+{
+ uint32_t dmarequest = 0x00U;
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+ husart->RxXferCount = 0x00U;
+ husart->TxXferCount = 0x00U;
+
+ /* Stop USART DMA Tx request if ongoing */
+ dmarequest = HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT);
+ if ((husart->State == HAL_USART_STATE_BUSY_TX) && dmarequest)
+ {
+ USART_EndTxTransfer(husart);
+ }
+
+ /* Stop USART DMA Rx request if ongoing */
+ dmarequest = HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR);
+ if ((husart->State == HAL_USART_STATE_BUSY_RX) && dmarequest)
+ {
+ USART_EndRxTransfer(husart);
+ }
+
+ husart->ErrorCode |= HAL_USART_ERROR_DMA;
+ husart->State = HAL_USART_STATE_READY;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Error Callback */
+ husart->ErrorCallback(husart);
+#else
+ /* Call legacy weak Error Callback */
+ HAL_USART_ErrorCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief This function handles USART Communication Timeout.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @param Flag specifies the USART flag to check.
+ * @param Status The new Flag status (SET or RESET).
+ * @param Tickstart Tick start value.
+ * @param Timeout Timeout duration.
+ * @retval HAL status
+ */
+static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout)
+{
+ /* Wait until flag is set */
+ while ((__HAL_USART_GET_FLAG(husart, Flag) ? SET : RESET) == Status)
+ {
+ /* Check for the Timeout */
+ if (Timeout != HAL_MAX_DELAY)
+ {
+ if ((Timeout == 0U) || ((HAL_GetTick() - Tickstart) > Timeout))
+ {
+ /* Disable the USART Transmit Complete Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_TXEIE);
+
+ /* Disable the USART RXNE Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_RXNEIE);
+
+ /* Disable the USART Parity Error Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(husart);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ return HAL_OK;
+}
+
+/**
+ * @brief End ongoing Tx transfer on USART peripheral (following error detection or Transmit completion).
+ * @param husart USART handle.
+ * @retval None
+ */
+static void USART_EndTxTransfer(USART_HandleTypeDef *husart)
+{
+ /* Disable TXEIE and TCIE interrupts */
+ CLEAR_BIT(husart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE));
+
+ /* At end of Tx process, restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+}
+
+/**
+ * @brief End ongoing Rx transfer on USART peripheral (following error detection or Reception completion).
+ * @param husart USART handle.
+ * @retval None
+ */
+static void USART_EndRxTransfer(USART_HandleTypeDef *husart)
+{
+ /* Disable RXNE, PE and ERR interrupts */
+ CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE));
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ /* At end of Rx process, restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+}
+
+/**
+ * @brief DMA USART communication abort callback, when initiated by HAL services on Error
+ * (To be called at end of DMA Abort procedure following error occurrence).
+ * @param hdma DMA handle.
+ * @retval None
+ */
+static void USART_DMAAbortOnError(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+ husart->RxXferCount = 0x00U;
+ husart->TxXferCount = 0x00U;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Error Callback */
+ husart->ErrorCallback(husart);
+#else
+ /* Call legacy weak Error Callback */
+ HAL_USART_ErrorCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief DMA USART Tx communication abort callback, when initiated by user
+ * (To be called at end of DMA Tx Abort procedure following user abort request).
+ * @note When this callback is executed, User Abort complete call back is called only if no
+ * Abort still ongoing for Rx DMA Handle.
+ * @param hdma DMA handle.
+ * @retval None
+ */
+static void USART_DMATxAbortCallback(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+ husart->hdmatx->XferAbortCallback = NULL;
+
+ /* Check if an Abort process is still ongoing */
+ if (husart->hdmarx != NULL)
+ {
+ if (husart->hdmarx->XferAbortCallback != NULL)
+ {
+ return;
+ }
+ }
+
+ /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */
+ husart->TxXferCount = 0x00U;
+ husart->RxXferCount = 0x00U;
+
+ /* Reset errorCode */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+
+ /* Restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Call user Abort complete callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Abort Complete Callback */
+ husart->AbortCpltCallback(husart);
+#else
+ /* Call legacy weak Abort Complete Callback */
+ HAL_USART_AbortCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief DMA USART Rx communication abort callback, when initiated by user
+ * (To be called at end of DMA Rx Abort procedure following user abort request).
+ * @note When this callback is executed, User Abort complete call back is called only if no
+ * Abort still ongoing for Tx DMA Handle.
+ * @param hdma DMA handle.
+ * @retval None
+ */
+static void USART_DMARxAbortCallback(DMA_HandleTypeDef *hdma)
+{
+ USART_HandleTypeDef *husart = (USART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+ husart->hdmarx->XferAbortCallback = NULL;
+
+ /* Check if an Abort process is still ongoing */
+ if (husart->hdmatx != NULL)
+ {
+ if (husart->hdmatx->XferAbortCallback != NULL)
+ {
+ return;
+ }
+ }
+
+ /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */
+ husart->TxXferCount = 0x00U;
+ husart->RxXferCount = 0x00U;
+
+ /* Reset errorCode */
+ husart->ErrorCode = HAL_USART_ERROR_NONE;
+
+ /* Restore husart->State to Ready */
+ husart->State = HAL_USART_STATE_READY;
+
+ /* Call user Abort complete callback */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Abort Complete Callback */
+ husart->AbortCpltCallback(husart);
+#else
+ /* Call legacy weak Abort Complete Callback */
+ HAL_USART_AbortCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief Simplex Send an amount of data in non-blocking mode.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ * @note The USART errors are not managed to avoid the overrun error.
+ */
+static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart)
+{
+ uint16_t *tmp;
+
+ if (husart->State == HAL_USART_STATE_BUSY_TX)
+ {
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ tmp = (uint16_t *) husart->pTxBuffPtr;
+ husart->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FF);
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ husart->pTxBuffPtr += 2U;
+ }
+ else
+ {
+ husart->pTxBuffPtr += 1U;
+ }
+ }
+ else
+ {
+ husart->Instance->DR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)0x00FF);
+ }
+
+ if (--husart->TxXferCount == 0U)
+ {
+ /* Disable the USART Transmit data register empty Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_TXEIE);
+
+ /* Enable the USART Transmit Complete Interrupt */
+ SET_BIT(husart->Instance->CR1, USART_CR1_TCIE);
+ }
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Wraps up transmission in non blocking mode.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart)
+{
+ /* Disable the USART Transmit Complete Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_TCIE);
+
+ /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ husart->State = HAL_USART_STATE_READY;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Complete Callback */
+ husart->TxCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Complete Callback */
+ HAL_USART_TxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Simplex Receive an amount of data in non-blocking mode.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart)
+{
+ uint16_t *tmp;
+ if (husart->State == HAL_USART_STATE_BUSY_RX)
+ {
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ tmp = (uint16_t *) husart->pRxBuffPtr;
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x01FF);
+ husart->pRxBuffPtr += 2U;
+ }
+ else
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x00FF);
+ husart->pRxBuffPtr += 1U;
+ }
+ if (--husart->RxXferCount != 0x00U)
+ {
+ /* Send dummy byte in order to generate the clock for the slave to send the next data */
+ husart->Instance->DR = (DUMMY_DATA & (uint16_t)0x01FF);
+ }
+ }
+ else
+ {
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x00FF);
+ }
+ else
+ {
+ *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x007F);
+ }
+
+ if (--husart->RxXferCount != 0x00U)
+ {
+ /* Send dummy byte in order to generate the clock for the slave to send the next data */
+ husart->Instance->DR = (DUMMY_DATA & (uint16_t)0x00FF);
+ }
+ }
+
+ if (husart->RxXferCount == 0U)
+ {
+ /* Disable the USART RXNE Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_RXNEIE);
+
+ /* Disable the USART Parity Error Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ husart->State = HAL_USART_STATE_READY;
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Rx Complete Callback */
+ husart->RxCpltCallback(husart);
+#else
+ /* Call legacy weak Rx Complete Callback */
+ HAL_USART_RxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+ return HAL_OK;
+ }
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Full-Duplex Send receive an amount of data in full-duplex mode (non-blocking).
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval HAL status
+ */
+static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart)
+{
+ uint16_t *tmp;
+
+ if (husart->State == HAL_USART_STATE_BUSY_TX_RX)
+ {
+ if (husart->TxXferCount != 0x00U)
+ {
+ if (__HAL_USART_GET_FLAG(husart, USART_FLAG_TXE) != RESET)
+ {
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ tmp = (uint16_t *) husart->pTxBuffPtr;
+ husart->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FF);
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ husart->pTxBuffPtr += 2U;
+ }
+ else
+ {
+ husart->pTxBuffPtr += 1U;
+ }
+ }
+ else
+ {
+ husart->Instance->DR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)0x00FF);
+ }
+ husart->TxXferCount--;
+
+ /* Check the latest data transmitted */
+ if (husart->TxXferCount == 0U)
+ {
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_TXEIE);
+ }
+ }
+ }
+
+ if (husart->RxXferCount != 0x00U)
+ {
+ if (__HAL_USART_GET_FLAG(husart, USART_FLAG_RXNE) != RESET)
+ {
+ if (husart->Init.WordLength == USART_WORDLENGTH_9B)
+ {
+ tmp = (uint16_t *) husart->pRxBuffPtr;
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x01FF);
+ husart->pRxBuffPtr += 2U;
+ }
+ else
+ {
+ *tmp = (uint16_t)(husart->Instance->DR & (uint16_t)0x00FF);
+ husart->pRxBuffPtr += 1U;
+ }
+ }
+ else
+ {
+ if (husart->Init.Parity == USART_PARITY_NONE)
+ {
+ *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x00FF);
+ }
+ else
+ {
+ *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->DR & (uint8_t)0x007F);
+ }
+ }
+ husart->RxXferCount--;
+ }
+ }
+
+ /* Check the latest data received */
+ if (husart->RxXferCount == 0U)
+ {
+ /* Disable the USART RXNE Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_RXNEIE);
+
+ /* Disable the USART Parity Error Interrupt */
+ CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE);
+
+ /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */
+ CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE);
+
+ husart->State = HAL_USART_STATE_READY;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+ /* Call registered Tx Rx Complete Callback */
+ husart->TxRxCpltCallback(husart);
+#else
+ /* Call legacy weak Tx Rx Complete Callback */
+ HAL_USART_TxRxCpltCallback(husart);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+ return HAL_OK;
+ }
+
+ return HAL_OK;
+ }
+ else
+ {
+ return HAL_BUSY;
+ }
+}
+
+/**
+ * @brief Configures the USART peripheral.
+ * @param husart Pointer to a USART_HandleTypeDef structure that contains
+ * the configuration information for the specified USART module.
+ * @retval None
+ */
+static void USART_SetConfig(USART_HandleTypeDef *husart)
+{
+ uint32_t tmpreg = 0x00U;
+ uint32_t pclk;
+
+ /* Check the parameters */
+ assert_param(IS_USART_INSTANCE(husart->Instance));
+ assert_param(IS_USART_POLARITY(husart->Init.CLKPolarity));
+ assert_param(IS_USART_PHASE(husart->Init.CLKPhase));
+ assert_param(IS_USART_LASTBIT(husart->Init.CLKLastBit));
+ assert_param(IS_USART_BAUDRATE(husart->Init.BaudRate));
+ assert_param(IS_USART_WORD_LENGTH(husart->Init.WordLength));
+ assert_param(IS_USART_STOPBITS(husart->Init.StopBits));
+ assert_param(IS_USART_PARITY(husart->Init.Parity));
+ assert_param(IS_USART_MODE(husart->Init.Mode));
+
+ /* The LBCL, CPOL and CPHA bits have to be selected when both the transmitter and the
+ receiver are disabled (TE=RE=0) to ensure that the clock pulses function correctly. */
+ CLEAR_BIT(husart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE));
+
+ /*---------------------------- USART CR2 Configuration ---------------------*/
+ tmpreg = husart->Instance->CR2;
+ /* Clear CLKEN, CPOL, CPHA and LBCL bits */
+ tmpreg &= (uint32_t)~((uint32_t)(USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_CLKEN | USART_CR2_LBCL | USART_CR2_STOP));
+ /* Configure the USART Clock, CPOL, CPHA and LastBit -----------------------*/
+ /* Set CPOL bit according to husart->Init.CLKPolarity value */
+ /* Set CPHA bit according to husart->Init.CLKPhase value */
+ /* Set LBCL bit according to husart->Init.CLKLastBit value */
+ /* Set Stop Bits: Set STOP[13:12] bits according to husart->Init.StopBits value */
+ tmpreg |= (uint32_t)(USART_CLOCK_ENABLE | husart->Init.CLKPolarity |
+ husart->Init.CLKPhase | husart->Init.CLKLastBit | husart->Init.StopBits);
+ /* Write to USART CR2 */
+ WRITE_REG(husart->Instance->CR2, (uint32_t)tmpreg);
+
+ /*-------------------------- USART CR1 Configuration -----------------------*/
+ tmpreg = husart->Instance->CR1;
+
+ /* Clear M, PCE, PS, TE and RE bits */
+ tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE));
+
+ /* Configure the USART Word Length, Parity and mode:
+ Set the M bits according to husart->Init.WordLength value
+ Set PCE and PS bits according to husart->Init.Parity value
+ Set TE and RE bits according to husart->Init.Mode value
+ */
+ tmpreg |= (uint32_t)husart->Init.WordLength | husart->Init.Parity | husart->Init.Mode;
+
+ /* Write to USART CR1 */
+ WRITE_REG(husart->Instance->CR1, (uint32_t)tmpreg);
+
+ /*-------------------------- USART CR3 Configuration -----------------------*/
+ /* Clear CTSE and RTSE bits */
+ CLEAR_BIT(husart->Instance->CR3, (USART_CR3_RTSE | USART_CR3_CTSE));
+
+ /*-------------------------- USART BRR Configuration -----------------------*/
+ if((husart->Instance == USART1))
+ {
+ pclk = HAL_RCC_GetPCLK2Freq();
+ husart->Instance->BRR = USART_BRR(pclk, husart->Init.BaudRate);
+ }
+ else
+ {
+ pclk = HAL_RCC_GetPCLK1Freq();
+ husart->Instance->BRR = USART_BRR(pclk, husart->Init.BaudRate);
+ }
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* HAL_USART_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|