diff options
Diffstat (limited to 'lib/pico-sdk/rp2350/hardware/regs/uart.h')
| -rw-r--r-- | lib/pico-sdk/rp2350/hardware/regs/uart.h | 1150 |
1 files changed, 1150 insertions, 0 deletions
diff --git a/lib/pico-sdk/rp2350/hardware/regs/uart.h b/lib/pico-sdk/rp2350/hardware/regs/uart.h new file mode 100644 index 00000000..0f7f17ec --- /dev/null +++ b/lib/pico-sdk/rp2350/hardware/regs/uart.h @@ -0,0 +1,1150 @@ +// THIS HEADER FILE IS AUTOMATICALLY GENERATED -- DO NOT EDIT + +/** + * Copyright (c) 2024 Raspberry Pi Ltd. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +// ============================================================================= +// Register block : UART +// Version : 1 +// Bus type : apb +// ============================================================================= +#ifndef _HARDWARE_REGS_UART_H +#define _HARDWARE_REGS_UART_H +// ============================================================================= +// Register : UART_UARTDR +// Description : Data Register, UARTDR +#define UART_UARTDR_OFFSET _u(0x00000000) +#define UART_UARTDR_BITS _u(0x00000fff) +#define UART_UARTDR_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTDR_OE +// Description : Overrun error. This bit is set to 1 if data is received and the +// receive FIFO is already full. This is cleared to 0 once there +// is an empty space in the FIFO and a new character can be +// written to it. +#define UART_UARTDR_OE_RESET "-" +#define UART_UARTDR_OE_BITS _u(0x00000800) +#define UART_UARTDR_OE_MSB _u(11) +#define UART_UARTDR_OE_LSB _u(11) +#define UART_UARTDR_OE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDR_BE +// Description : Break error. This bit is set to 1 if a break condition was +// detected, indicating that the received data input was held LOW +// for longer than a full-word transmission time (defined as +// start, data, parity and stop bits). In FIFO mode, this error is +// associated with the character at the top of the FIFO. When a +// break occurs, only one 0 character is loaded into the FIFO. The +// next character is only enabled after the receive data input +// goes to a 1 (marking state), and the next valid start bit is +// received. +#define UART_UARTDR_BE_RESET "-" +#define UART_UARTDR_BE_BITS _u(0x00000400) +#define UART_UARTDR_BE_MSB _u(10) +#define UART_UARTDR_BE_LSB _u(10) +#define UART_UARTDR_BE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDR_PE +// Description : Parity error. When set to 1, it indicates that the parity of +// the received data character does not match the parity that the +// EPS and SPS bits in the Line Control Register, UARTLCR_H. In +// FIFO mode, this error is associated with the character at the +// top of the FIFO. +#define UART_UARTDR_PE_RESET "-" +#define UART_UARTDR_PE_BITS _u(0x00000200) +#define UART_UARTDR_PE_MSB _u(9) +#define UART_UARTDR_PE_LSB _u(9) +#define UART_UARTDR_PE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDR_FE +// Description : Framing error. When set to 1, it indicates that the received +// character did not have a valid stop bit (a valid stop bit is +// 1). In FIFO mode, this error is associated with the character +// at the top of the FIFO. +#define UART_UARTDR_FE_RESET "-" +#define UART_UARTDR_FE_BITS _u(0x00000100) +#define UART_UARTDR_FE_MSB _u(8) +#define UART_UARTDR_FE_LSB _u(8) +#define UART_UARTDR_FE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDR_DATA +// Description : Receive (read) data character. Transmit (write) data character. +#define UART_UARTDR_DATA_RESET "-" +#define UART_UARTDR_DATA_BITS _u(0x000000ff) +#define UART_UARTDR_DATA_MSB _u(7) +#define UART_UARTDR_DATA_LSB _u(0) +#define UART_UARTDR_DATA_ACCESS "RWF" +// ============================================================================= +// Register : UART_UARTRSR +// Description : Receive Status Register/Error Clear Register, UARTRSR/UARTECR +#define UART_UARTRSR_OFFSET _u(0x00000004) +#define UART_UARTRSR_BITS _u(0x0000000f) +#define UART_UARTRSR_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTRSR_OE +// Description : Overrun error. This bit is set to 1 if data is received and the +// FIFO is already full. This bit is cleared to 0 by a write to +// UARTECR. The FIFO contents remain valid because no more data is +// written when the FIFO is full, only the contents of the shift +// register are overwritten. The CPU must now read the data, to +// empty the FIFO. +#define UART_UARTRSR_OE_RESET _u(0x0) +#define UART_UARTRSR_OE_BITS _u(0x00000008) +#define UART_UARTRSR_OE_MSB _u(3) +#define UART_UARTRSR_OE_LSB _u(3) +#define UART_UARTRSR_OE_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRSR_BE +// Description : Break error. This bit is set to 1 if a break condition was +// detected, indicating that the received data input was held LOW +// for longer than a full-word transmission time (defined as +// start, data, parity, and stop bits). This bit is cleared to 0 +// after a write to UARTECR. In FIFO mode, this error is +// associated with the character at the top of the FIFO. When a +// break occurs, only one 0 character is loaded into the FIFO. The +// next character is only enabled after the receive data input +// goes to a 1 (marking state) and the next valid start bit is +// received. +#define UART_UARTRSR_BE_RESET _u(0x0) +#define UART_UARTRSR_BE_BITS _u(0x00000004) +#define UART_UARTRSR_BE_MSB _u(2) +#define UART_UARTRSR_BE_LSB _u(2) +#define UART_UARTRSR_BE_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRSR_PE +// Description : Parity error. When set to 1, it indicates that the parity of +// the received data character does not match the parity that the +// EPS and SPS bits in the Line Control Register, UARTLCR_H. This +// bit is cleared to 0 by a write to UARTECR. In FIFO mode, this +// error is associated with the character at the top of the FIFO. +#define UART_UARTRSR_PE_RESET _u(0x0) +#define UART_UARTRSR_PE_BITS _u(0x00000002) +#define UART_UARTRSR_PE_MSB _u(1) +#define UART_UARTRSR_PE_LSB _u(1) +#define UART_UARTRSR_PE_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRSR_FE +// Description : Framing error. When set to 1, it indicates that the received +// character did not have a valid stop bit (a valid stop bit is +// 1). This bit is cleared to 0 by a write to UARTECR. In FIFO +// mode, this error is associated with the character at the top of +// the FIFO. +#define UART_UARTRSR_FE_RESET _u(0x0) +#define UART_UARTRSR_FE_BITS _u(0x00000001) +#define UART_UARTRSR_FE_MSB _u(0) +#define UART_UARTRSR_FE_LSB _u(0) +#define UART_UARTRSR_FE_ACCESS "WC" +// ============================================================================= +// Register : UART_UARTFR +// Description : Flag Register, UARTFR +#define UART_UARTFR_OFFSET _u(0x00000018) +#define UART_UARTFR_BITS _u(0x000001ff) +#define UART_UARTFR_RESET _u(0x00000090) +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_RI +// Description : Ring indicator. This bit is the complement of the UART ring +// indicator, nUARTRI, modem status input. That is, the bit is 1 +// when nUARTRI is LOW. +#define UART_UARTFR_RI_RESET "-" +#define UART_UARTFR_RI_BITS _u(0x00000100) +#define UART_UARTFR_RI_MSB _u(8) +#define UART_UARTFR_RI_LSB _u(8) +#define UART_UARTFR_RI_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_TXFE +// Description : Transmit FIFO empty. The meaning of this bit depends on the +// state of the FEN bit in the Line Control Register, UARTLCR_H. +// If the FIFO is disabled, this bit is set when the transmit +// holding register is empty. If the FIFO is enabled, the TXFE bit +// is set when the transmit FIFO is empty. This bit does not +// indicate if there is data in the transmit shift register. +#define UART_UARTFR_TXFE_RESET _u(0x1) +#define UART_UARTFR_TXFE_BITS _u(0x00000080) +#define UART_UARTFR_TXFE_MSB _u(7) +#define UART_UARTFR_TXFE_LSB _u(7) +#define UART_UARTFR_TXFE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_RXFF +// Description : Receive FIFO full. The meaning of this bit depends on the state +// of the FEN bit in the UARTLCR_H Register. If the FIFO is +// disabled, this bit is set when the receive holding register is +// full. If the FIFO is enabled, the RXFF bit is set when the +// receive FIFO is full. +#define UART_UARTFR_RXFF_RESET _u(0x0) +#define UART_UARTFR_RXFF_BITS _u(0x00000040) +#define UART_UARTFR_RXFF_MSB _u(6) +#define UART_UARTFR_RXFF_LSB _u(6) +#define UART_UARTFR_RXFF_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_TXFF +// Description : Transmit FIFO full. The meaning of this bit depends on the +// state of the FEN bit in the UARTLCR_H Register. If the FIFO is +// disabled, this bit is set when the transmit holding register is +// full. If the FIFO is enabled, the TXFF bit is set when the +// transmit FIFO is full. +#define UART_UARTFR_TXFF_RESET _u(0x0) +#define UART_UARTFR_TXFF_BITS _u(0x00000020) +#define UART_UARTFR_TXFF_MSB _u(5) +#define UART_UARTFR_TXFF_LSB _u(5) +#define UART_UARTFR_TXFF_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_RXFE +// Description : Receive FIFO empty. The meaning of this bit depends on the +// state of the FEN bit in the UARTLCR_H Register. If the FIFO is +// disabled, this bit is set when the receive holding register is +// empty. If the FIFO is enabled, the RXFE bit is set when the +// receive FIFO is empty. +#define UART_UARTFR_RXFE_RESET _u(0x1) +#define UART_UARTFR_RXFE_BITS _u(0x00000010) +#define UART_UARTFR_RXFE_MSB _u(4) +#define UART_UARTFR_RXFE_LSB _u(4) +#define UART_UARTFR_RXFE_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_BUSY +// Description : UART busy. If this bit is set to 1, the UART is busy +// transmitting data. This bit remains set until the complete +// byte, including all the stop bits, has been sent from the shift +// register. This bit is set as soon as the transmit FIFO becomes +// non-empty, regardless of whether the UART is enabled or not. +#define UART_UARTFR_BUSY_RESET _u(0x0) +#define UART_UARTFR_BUSY_BITS _u(0x00000008) +#define UART_UARTFR_BUSY_MSB _u(3) +#define UART_UARTFR_BUSY_LSB _u(3) +#define UART_UARTFR_BUSY_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_DCD +// Description : Data carrier detect. This bit is the complement of the UART +// data carrier detect, nUARTDCD, modem status input. That is, the +// bit is 1 when nUARTDCD is LOW. +#define UART_UARTFR_DCD_RESET "-" +#define UART_UARTFR_DCD_BITS _u(0x00000004) +#define UART_UARTFR_DCD_MSB _u(2) +#define UART_UARTFR_DCD_LSB _u(2) +#define UART_UARTFR_DCD_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_DSR +// Description : Data set ready. This bit is the complement of the UART data set +// ready, nUARTDSR, modem status input. That is, the bit is 1 when +// nUARTDSR is LOW. +#define UART_UARTFR_DSR_RESET "-" +#define UART_UARTFR_DSR_BITS _u(0x00000002) +#define UART_UARTFR_DSR_MSB _u(1) +#define UART_UARTFR_DSR_LSB _u(1) +#define UART_UARTFR_DSR_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTFR_CTS +// Description : Clear to send. This bit is the complement of the UART clear to +// send, nUARTCTS, modem status input. That is, the bit is 1 when +// nUARTCTS is LOW. +#define UART_UARTFR_CTS_RESET "-" +#define UART_UARTFR_CTS_BITS _u(0x00000001) +#define UART_UARTFR_CTS_MSB _u(0) +#define UART_UARTFR_CTS_LSB _u(0) +#define UART_UARTFR_CTS_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTILPR +// Description : IrDA Low-Power Counter Register, UARTILPR +#define UART_UARTILPR_OFFSET _u(0x00000020) +#define UART_UARTILPR_BITS _u(0x000000ff) +#define UART_UARTILPR_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTILPR_ILPDVSR +// Description : 8-bit low-power divisor value. These bits are cleared to 0 at +// reset. +#define UART_UARTILPR_ILPDVSR_RESET _u(0x00) +#define UART_UARTILPR_ILPDVSR_BITS _u(0x000000ff) +#define UART_UARTILPR_ILPDVSR_MSB _u(7) +#define UART_UARTILPR_ILPDVSR_LSB _u(0) +#define UART_UARTILPR_ILPDVSR_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTIBRD +// Description : Integer Baud Rate Register, UARTIBRD +#define UART_UARTIBRD_OFFSET _u(0x00000024) +#define UART_UARTIBRD_BITS _u(0x0000ffff) +#define UART_UARTIBRD_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTIBRD_BAUD_DIVINT +// Description : The integer baud rate divisor. These bits are cleared to 0 on +// reset. +#define UART_UARTIBRD_BAUD_DIVINT_RESET _u(0x0000) +#define UART_UARTIBRD_BAUD_DIVINT_BITS _u(0x0000ffff) +#define UART_UARTIBRD_BAUD_DIVINT_MSB _u(15) +#define UART_UARTIBRD_BAUD_DIVINT_LSB _u(0) +#define UART_UARTIBRD_BAUD_DIVINT_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTFBRD +// Description : Fractional Baud Rate Register, UARTFBRD +#define UART_UARTFBRD_OFFSET _u(0x00000028) +#define UART_UARTFBRD_BITS _u(0x0000003f) +#define UART_UARTFBRD_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTFBRD_BAUD_DIVFRAC +// Description : The fractional baud rate divisor. These bits are cleared to 0 +// on reset. +#define UART_UARTFBRD_BAUD_DIVFRAC_RESET _u(0x00) +#define UART_UARTFBRD_BAUD_DIVFRAC_BITS _u(0x0000003f) +#define UART_UARTFBRD_BAUD_DIVFRAC_MSB _u(5) +#define UART_UARTFBRD_BAUD_DIVFRAC_LSB _u(0) +#define UART_UARTFBRD_BAUD_DIVFRAC_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTLCR_H +// Description : Line Control Register, UARTLCR_H +#define UART_UARTLCR_H_OFFSET _u(0x0000002c) +#define UART_UARTLCR_H_BITS _u(0x000000ff) +#define UART_UARTLCR_H_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_SPS +// Description : Stick parity select. 0 = stick parity is disabled 1 = either: * +// if the EPS bit is 0 then the parity bit is transmitted and +// checked as a 1 * if the EPS bit is 1 then the parity bit is +// transmitted and checked as a 0. This bit has no effect when the +// PEN bit disables parity checking and generation. +#define UART_UARTLCR_H_SPS_RESET _u(0x0) +#define UART_UARTLCR_H_SPS_BITS _u(0x00000080) +#define UART_UARTLCR_H_SPS_MSB _u(7) +#define UART_UARTLCR_H_SPS_LSB _u(7) +#define UART_UARTLCR_H_SPS_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_WLEN +// Description : Word length. These bits indicate the number of data bits +// transmitted or received in a frame as follows: b11 = 8 bits b10 +// = 7 bits b01 = 6 bits b00 = 5 bits. +#define UART_UARTLCR_H_WLEN_RESET _u(0x0) +#define UART_UARTLCR_H_WLEN_BITS _u(0x00000060) +#define UART_UARTLCR_H_WLEN_MSB _u(6) +#define UART_UARTLCR_H_WLEN_LSB _u(5) +#define UART_UARTLCR_H_WLEN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_FEN +// Description : Enable FIFOs: 0 = FIFOs are disabled (character mode) that is, +// the FIFOs become 1-byte-deep holding registers 1 = transmit and +// receive FIFO buffers are enabled (FIFO mode). +#define UART_UARTLCR_H_FEN_RESET _u(0x0) +#define UART_UARTLCR_H_FEN_BITS _u(0x00000010) +#define UART_UARTLCR_H_FEN_MSB _u(4) +#define UART_UARTLCR_H_FEN_LSB _u(4) +#define UART_UARTLCR_H_FEN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_STP2 +// Description : Two stop bits select. If this bit is set to 1, two stop bits +// are transmitted at the end of the frame. The receive logic does +// not check for two stop bits being received. +#define UART_UARTLCR_H_STP2_RESET _u(0x0) +#define UART_UARTLCR_H_STP2_BITS _u(0x00000008) +#define UART_UARTLCR_H_STP2_MSB _u(3) +#define UART_UARTLCR_H_STP2_LSB _u(3) +#define UART_UARTLCR_H_STP2_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_EPS +// Description : Even parity select. Controls the type of parity the UART uses +// during transmission and reception: 0 = odd parity. The UART +// generates or checks for an odd number of 1s in the data and +// parity bits. 1 = even parity. The UART generates or checks for +// an even number of 1s in the data and parity bits. This bit has +// no effect when the PEN bit disables parity checking and +// generation. +#define UART_UARTLCR_H_EPS_RESET _u(0x0) +#define UART_UARTLCR_H_EPS_BITS _u(0x00000004) +#define UART_UARTLCR_H_EPS_MSB _u(2) +#define UART_UARTLCR_H_EPS_LSB _u(2) +#define UART_UARTLCR_H_EPS_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_PEN +// Description : Parity enable: 0 = parity is disabled and no parity bit added +// to the data frame 1 = parity checking and generation is +// enabled. +#define UART_UARTLCR_H_PEN_RESET _u(0x0) +#define UART_UARTLCR_H_PEN_BITS _u(0x00000002) +#define UART_UARTLCR_H_PEN_MSB _u(1) +#define UART_UARTLCR_H_PEN_LSB _u(1) +#define UART_UARTLCR_H_PEN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTLCR_H_BRK +// Description : Send break. If this bit is set to 1, a low-level is continually +// output on the UARTTXD output, after completing transmission of +// the current character. For the proper execution of the break +// command, the software must set this bit for at least two +// complete frames. For normal use, this bit must be cleared to 0. +#define UART_UARTLCR_H_BRK_RESET _u(0x0) +#define UART_UARTLCR_H_BRK_BITS _u(0x00000001) +#define UART_UARTLCR_H_BRK_MSB _u(0) +#define UART_UARTLCR_H_BRK_LSB _u(0) +#define UART_UARTLCR_H_BRK_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTCR +// Description : Control Register, UARTCR +#define UART_UARTCR_OFFSET _u(0x00000030) +#define UART_UARTCR_BITS _u(0x0000ff87) +#define UART_UARTCR_RESET _u(0x00000300) +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_CTSEN +// Description : CTS hardware flow control enable. If this bit is set to 1, CTS +// hardware flow control is enabled. Data is only transmitted when +// the nUARTCTS signal is asserted. +#define UART_UARTCR_CTSEN_RESET _u(0x0) +#define UART_UARTCR_CTSEN_BITS _u(0x00008000) +#define UART_UARTCR_CTSEN_MSB _u(15) +#define UART_UARTCR_CTSEN_LSB _u(15) +#define UART_UARTCR_CTSEN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_RTSEN +// Description : RTS hardware flow control enable. If this bit is set to 1, RTS +// hardware flow control is enabled. Data is only requested when +// there is space in the receive FIFO for it to be received. +#define UART_UARTCR_RTSEN_RESET _u(0x0) +#define UART_UARTCR_RTSEN_BITS _u(0x00004000) +#define UART_UARTCR_RTSEN_MSB _u(14) +#define UART_UARTCR_RTSEN_LSB _u(14) +#define UART_UARTCR_RTSEN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_OUT2 +// Description : This bit is the complement of the UART Out2 (nUARTOut2) modem +// status output. That is, when the bit is programmed to a 1, the +// output is 0. For DTE this can be used as Ring Indicator (RI). +#define UART_UARTCR_OUT2_RESET _u(0x0) +#define UART_UARTCR_OUT2_BITS _u(0x00002000) +#define UART_UARTCR_OUT2_MSB _u(13) +#define UART_UARTCR_OUT2_LSB _u(13) +#define UART_UARTCR_OUT2_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_OUT1 +// Description : This bit is the complement of the UART Out1 (nUARTOut1) modem +// status output. That is, when the bit is programmed to a 1 the +// output is 0. For DTE this can be used as Data Carrier Detect +// (DCD). +#define UART_UARTCR_OUT1_RESET _u(0x0) +#define UART_UARTCR_OUT1_BITS _u(0x00001000) +#define UART_UARTCR_OUT1_MSB _u(12) +#define UART_UARTCR_OUT1_LSB _u(12) +#define UART_UARTCR_OUT1_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_RTS +// Description : Request to send. This bit is the complement of the UART request +// to send, nUARTRTS, modem status output. That is, when the bit +// is programmed to a 1 then nUARTRTS is LOW. +#define UART_UARTCR_RTS_RESET _u(0x0) +#define UART_UARTCR_RTS_BITS _u(0x00000800) +#define UART_UARTCR_RTS_MSB _u(11) +#define UART_UARTCR_RTS_LSB _u(11) +#define UART_UARTCR_RTS_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_DTR +// Description : Data transmit ready. This bit is the complement of the UART +// data transmit ready, nUARTDTR, modem status output. That is, +// when the bit is programmed to a 1 then nUARTDTR is LOW. +#define UART_UARTCR_DTR_RESET _u(0x0) +#define UART_UARTCR_DTR_BITS _u(0x00000400) +#define UART_UARTCR_DTR_MSB _u(10) +#define UART_UARTCR_DTR_LSB _u(10) +#define UART_UARTCR_DTR_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_RXE +// Description : Receive enable. If this bit is set to 1, the receive section of +// the UART is enabled. Data reception occurs for either UART +// signals or SIR signals depending on the setting of the SIREN +// bit. When the UART is disabled in the middle of reception, it +// completes the current character before stopping. +#define UART_UARTCR_RXE_RESET _u(0x1) +#define UART_UARTCR_RXE_BITS _u(0x00000200) +#define UART_UARTCR_RXE_MSB _u(9) +#define UART_UARTCR_RXE_LSB _u(9) +#define UART_UARTCR_RXE_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_TXE +// Description : Transmit enable. If this bit is set to 1, the transmit section +// of the UART is enabled. Data transmission occurs for either +// UART signals, or SIR signals depending on the setting of the +// SIREN bit. When the UART is disabled in the middle of +// transmission, it completes the current character before +// stopping. +#define UART_UARTCR_TXE_RESET _u(0x1) +#define UART_UARTCR_TXE_BITS _u(0x00000100) +#define UART_UARTCR_TXE_MSB _u(8) +#define UART_UARTCR_TXE_LSB _u(8) +#define UART_UARTCR_TXE_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_LBE +// Description : Loopback enable. If this bit is set to 1 and the SIREN bit is +// set to 1 and the SIRTEST bit in the Test Control Register, +// UARTTCR is set to 1, then the nSIROUT path is inverted, and fed +// through to the SIRIN path. The SIRTEST bit in the test register +// must be set to 1 to override the normal half-duplex SIR +// operation. This must be the requirement for accessing the test +// registers during normal operation, and SIRTEST must be cleared +// to 0 when loopback testing is finished. This feature reduces +// the amount of external coupling required during system test. If +// this bit is set to 1, and the SIRTEST bit is set to 0, the +// UARTTXD path is fed through to the UARTRXD path. In either SIR +// mode or UART mode, when this bit is set, the modem outputs are +// also fed through to the modem inputs. This bit is cleared to 0 +// on reset, to disable loopback. +#define UART_UARTCR_LBE_RESET _u(0x0) +#define UART_UARTCR_LBE_BITS _u(0x00000080) +#define UART_UARTCR_LBE_MSB _u(7) +#define UART_UARTCR_LBE_LSB _u(7) +#define UART_UARTCR_LBE_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_SIRLP +// Description : SIR low-power IrDA mode. This bit selects the IrDA encoding +// mode. If this bit is cleared to 0, low-level bits are +// transmitted as an active high pulse with a width of 3 / 16th of +// the bit period. If this bit is set to 1, low-level bits are +// transmitted with a pulse width that is 3 times the period of +// the IrLPBaud16 input signal, regardless of the selected bit +// rate. Setting this bit uses less power, but might reduce +// transmission distances. +#define UART_UARTCR_SIRLP_RESET _u(0x0) +#define UART_UARTCR_SIRLP_BITS _u(0x00000004) +#define UART_UARTCR_SIRLP_MSB _u(2) +#define UART_UARTCR_SIRLP_LSB _u(2) +#define UART_UARTCR_SIRLP_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_SIREN +// Description : SIR enable: 0 = IrDA SIR ENDEC is disabled. nSIROUT remains LOW +// (no light pulse generated), and signal transitions on SIRIN +// have no effect. 1 = IrDA SIR ENDEC is enabled. Data is +// transmitted and received on nSIROUT and SIRIN. UARTTXD remains +// HIGH, in the marking state. Signal transitions on UARTRXD or +// modem status inputs have no effect. This bit has no effect if +// the UARTEN bit disables the UART. +#define UART_UARTCR_SIREN_RESET _u(0x0) +#define UART_UARTCR_SIREN_BITS _u(0x00000002) +#define UART_UARTCR_SIREN_MSB _u(1) +#define UART_UARTCR_SIREN_LSB _u(1) +#define UART_UARTCR_SIREN_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTCR_UARTEN +// Description : UART enable: 0 = UART is disabled. If the UART is disabled in +// the middle of transmission or reception, it completes the +// current character before stopping. 1 = the UART is enabled. +// Data transmission and reception occurs for either UART signals +// or SIR signals depending on the setting of the SIREN bit. +#define UART_UARTCR_UARTEN_RESET _u(0x0) +#define UART_UARTCR_UARTEN_BITS _u(0x00000001) +#define UART_UARTCR_UARTEN_MSB _u(0) +#define UART_UARTCR_UARTEN_LSB _u(0) +#define UART_UARTCR_UARTEN_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTIFLS +// Description : Interrupt FIFO Level Select Register, UARTIFLS +#define UART_UARTIFLS_OFFSET _u(0x00000034) +#define UART_UARTIFLS_BITS _u(0x0000003f) +#define UART_UARTIFLS_RESET _u(0x00000012) +// ----------------------------------------------------------------------------- +// Field : UART_UARTIFLS_RXIFLSEL +// Description : Receive interrupt FIFO level select. The trigger points for the +// receive interrupt are as follows: b000 = Receive FIFO becomes +// >= 1 / 8 full b001 = Receive FIFO becomes >= 1 / 4 full b010 = +// Receive FIFO becomes >= 1 / 2 full b011 = Receive FIFO becomes +// >= 3 / 4 full b100 = Receive FIFO becomes >= 7 / 8 full +// b101-b111 = reserved. +#define UART_UARTIFLS_RXIFLSEL_RESET _u(0x2) +#define UART_UARTIFLS_RXIFLSEL_BITS _u(0x00000038) +#define UART_UARTIFLS_RXIFLSEL_MSB _u(5) +#define UART_UARTIFLS_RXIFLSEL_LSB _u(3) +#define UART_UARTIFLS_RXIFLSEL_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIFLS_TXIFLSEL +// Description : Transmit interrupt FIFO level select. The trigger points for +// the transmit interrupt are as follows: b000 = Transmit FIFO +// becomes <= 1 / 8 full b001 = Transmit FIFO becomes <= 1 / 4 +// full b010 = Transmit FIFO becomes <= 1 / 2 full b011 = Transmit +// FIFO becomes <= 3 / 4 full b100 = Transmit FIFO becomes <= 7 / +// 8 full b101-b111 = reserved. +#define UART_UARTIFLS_TXIFLSEL_RESET _u(0x2) +#define UART_UARTIFLS_TXIFLSEL_BITS _u(0x00000007) +#define UART_UARTIFLS_TXIFLSEL_MSB _u(2) +#define UART_UARTIFLS_TXIFLSEL_LSB _u(0) +#define UART_UARTIFLS_TXIFLSEL_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTIMSC +// Description : Interrupt Mask Set/Clear Register, UARTIMSC +#define UART_UARTIMSC_OFFSET _u(0x00000038) +#define UART_UARTIMSC_BITS _u(0x000007ff) +#define UART_UARTIMSC_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_OEIM +// Description : Overrun error interrupt mask. A read returns the current mask +// for the UARTOEINTR interrupt. On a write of 1, the mask of the +// UARTOEINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_OEIM_RESET _u(0x0) +#define UART_UARTIMSC_OEIM_BITS _u(0x00000400) +#define UART_UARTIMSC_OEIM_MSB _u(10) +#define UART_UARTIMSC_OEIM_LSB _u(10) +#define UART_UARTIMSC_OEIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_BEIM +// Description : Break error interrupt mask. A read returns the current mask for +// the UARTBEINTR interrupt. On a write of 1, the mask of the +// UARTBEINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_BEIM_RESET _u(0x0) +#define UART_UARTIMSC_BEIM_BITS _u(0x00000200) +#define UART_UARTIMSC_BEIM_MSB _u(9) +#define UART_UARTIMSC_BEIM_LSB _u(9) +#define UART_UARTIMSC_BEIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_PEIM +// Description : Parity error interrupt mask. A read returns the current mask +// for the UARTPEINTR interrupt. On a write of 1, the mask of the +// UARTPEINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_PEIM_RESET _u(0x0) +#define UART_UARTIMSC_PEIM_BITS _u(0x00000100) +#define UART_UARTIMSC_PEIM_MSB _u(8) +#define UART_UARTIMSC_PEIM_LSB _u(8) +#define UART_UARTIMSC_PEIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_FEIM +// Description : Framing error interrupt mask. A read returns the current mask +// for the UARTFEINTR interrupt. On a write of 1, the mask of the +// UARTFEINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_FEIM_RESET _u(0x0) +#define UART_UARTIMSC_FEIM_BITS _u(0x00000080) +#define UART_UARTIMSC_FEIM_MSB _u(7) +#define UART_UARTIMSC_FEIM_LSB _u(7) +#define UART_UARTIMSC_FEIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_RTIM +// Description : Receive timeout interrupt mask. A read returns the current mask +// for the UARTRTINTR interrupt. On a write of 1, the mask of the +// UARTRTINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_RTIM_RESET _u(0x0) +#define UART_UARTIMSC_RTIM_BITS _u(0x00000040) +#define UART_UARTIMSC_RTIM_MSB _u(6) +#define UART_UARTIMSC_RTIM_LSB _u(6) +#define UART_UARTIMSC_RTIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_TXIM +// Description : Transmit interrupt mask. A read returns the current mask for +// the UARTTXINTR interrupt. On a write of 1, the mask of the +// UARTTXINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_TXIM_RESET _u(0x0) +#define UART_UARTIMSC_TXIM_BITS _u(0x00000020) +#define UART_UARTIMSC_TXIM_MSB _u(5) +#define UART_UARTIMSC_TXIM_LSB _u(5) +#define UART_UARTIMSC_TXIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_RXIM +// Description : Receive interrupt mask. A read returns the current mask for the +// UARTRXINTR interrupt. On a write of 1, the mask of the +// UARTRXINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_RXIM_RESET _u(0x0) +#define UART_UARTIMSC_RXIM_BITS _u(0x00000010) +#define UART_UARTIMSC_RXIM_MSB _u(4) +#define UART_UARTIMSC_RXIM_LSB _u(4) +#define UART_UARTIMSC_RXIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_DSRMIM +// Description : nUARTDSR modem interrupt mask. A read returns the current mask +// for the UARTDSRINTR interrupt. On a write of 1, the mask of the +// UARTDSRINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_DSRMIM_RESET _u(0x0) +#define UART_UARTIMSC_DSRMIM_BITS _u(0x00000008) +#define UART_UARTIMSC_DSRMIM_MSB _u(3) +#define UART_UARTIMSC_DSRMIM_LSB _u(3) +#define UART_UARTIMSC_DSRMIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_DCDMIM +// Description : nUARTDCD modem interrupt mask. A read returns the current mask +// for the UARTDCDINTR interrupt. On a write of 1, the mask of the +// UARTDCDINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_DCDMIM_RESET _u(0x0) +#define UART_UARTIMSC_DCDMIM_BITS _u(0x00000004) +#define UART_UARTIMSC_DCDMIM_MSB _u(2) +#define UART_UARTIMSC_DCDMIM_LSB _u(2) +#define UART_UARTIMSC_DCDMIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_CTSMIM +// Description : nUARTCTS modem interrupt mask. A read returns the current mask +// for the UARTCTSINTR interrupt. On a write of 1, the mask of the +// UARTCTSINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_CTSMIM_RESET _u(0x0) +#define UART_UARTIMSC_CTSMIM_BITS _u(0x00000002) +#define UART_UARTIMSC_CTSMIM_MSB _u(1) +#define UART_UARTIMSC_CTSMIM_LSB _u(1) +#define UART_UARTIMSC_CTSMIM_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTIMSC_RIMIM +// Description : nUARTRI modem interrupt mask. A read returns the current mask +// for the UARTRIINTR interrupt. On a write of 1, the mask of the +// UARTRIINTR interrupt is set. A write of 0 clears the mask. +#define UART_UARTIMSC_RIMIM_RESET _u(0x0) +#define UART_UARTIMSC_RIMIM_BITS _u(0x00000001) +#define UART_UARTIMSC_RIMIM_MSB _u(0) +#define UART_UARTIMSC_RIMIM_LSB _u(0) +#define UART_UARTIMSC_RIMIM_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTRIS +// Description : Raw Interrupt Status Register, UARTRIS +#define UART_UARTRIS_OFFSET _u(0x0000003c) +#define UART_UARTRIS_BITS _u(0x000007ff) +#define UART_UARTRIS_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_OERIS +// Description : Overrun error interrupt status. Returns the raw interrupt state +// of the UARTOEINTR interrupt. +#define UART_UARTRIS_OERIS_RESET _u(0x0) +#define UART_UARTRIS_OERIS_BITS _u(0x00000400) +#define UART_UARTRIS_OERIS_MSB _u(10) +#define UART_UARTRIS_OERIS_LSB _u(10) +#define UART_UARTRIS_OERIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_BERIS +// Description : Break error interrupt status. Returns the raw interrupt state +// of the UARTBEINTR interrupt. +#define UART_UARTRIS_BERIS_RESET _u(0x0) +#define UART_UARTRIS_BERIS_BITS _u(0x00000200) +#define UART_UARTRIS_BERIS_MSB _u(9) +#define UART_UARTRIS_BERIS_LSB _u(9) +#define UART_UARTRIS_BERIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_PERIS +// Description : Parity error interrupt status. Returns the raw interrupt state +// of the UARTPEINTR interrupt. +#define UART_UARTRIS_PERIS_RESET _u(0x0) +#define UART_UARTRIS_PERIS_BITS _u(0x00000100) +#define UART_UARTRIS_PERIS_MSB _u(8) +#define UART_UARTRIS_PERIS_LSB _u(8) +#define UART_UARTRIS_PERIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_FERIS +// Description : Framing error interrupt status. Returns the raw interrupt state +// of the UARTFEINTR interrupt. +#define UART_UARTRIS_FERIS_RESET _u(0x0) +#define UART_UARTRIS_FERIS_BITS _u(0x00000080) +#define UART_UARTRIS_FERIS_MSB _u(7) +#define UART_UARTRIS_FERIS_LSB _u(7) +#define UART_UARTRIS_FERIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_RTRIS +// Description : Receive timeout interrupt status. Returns the raw interrupt +// state of the UARTRTINTR interrupt. a +#define UART_UARTRIS_RTRIS_RESET _u(0x0) +#define UART_UARTRIS_RTRIS_BITS _u(0x00000040) +#define UART_UARTRIS_RTRIS_MSB _u(6) +#define UART_UARTRIS_RTRIS_LSB _u(6) +#define UART_UARTRIS_RTRIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_TXRIS +// Description : Transmit interrupt status. Returns the raw interrupt state of +// the UARTTXINTR interrupt. +#define UART_UARTRIS_TXRIS_RESET _u(0x0) +#define UART_UARTRIS_TXRIS_BITS _u(0x00000020) +#define UART_UARTRIS_TXRIS_MSB _u(5) +#define UART_UARTRIS_TXRIS_LSB _u(5) +#define UART_UARTRIS_TXRIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_RXRIS +// Description : Receive interrupt status. Returns the raw interrupt state of +// the UARTRXINTR interrupt. +#define UART_UARTRIS_RXRIS_RESET _u(0x0) +#define UART_UARTRIS_RXRIS_BITS _u(0x00000010) +#define UART_UARTRIS_RXRIS_MSB _u(4) +#define UART_UARTRIS_RXRIS_LSB _u(4) +#define UART_UARTRIS_RXRIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_DSRRMIS +// Description : nUARTDSR modem interrupt status. Returns the raw interrupt +// state of the UARTDSRINTR interrupt. +#define UART_UARTRIS_DSRRMIS_RESET "-" +#define UART_UARTRIS_DSRRMIS_BITS _u(0x00000008) +#define UART_UARTRIS_DSRRMIS_MSB _u(3) +#define UART_UARTRIS_DSRRMIS_LSB _u(3) +#define UART_UARTRIS_DSRRMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_DCDRMIS +// Description : nUARTDCD modem interrupt status. Returns the raw interrupt +// state of the UARTDCDINTR interrupt. +#define UART_UARTRIS_DCDRMIS_RESET "-" +#define UART_UARTRIS_DCDRMIS_BITS _u(0x00000004) +#define UART_UARTRIS_DCDRMIS_MSB _u(2) +#define UART_UARTRIS_DCDRMIS_LSB _u(2) +#define UART_UARTRIS_DCDRMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_CTSRMIS +// Description : nUARTCTS modem interrupt status. Returns the raw interrupt +// state of the UARTCTSINTR interrupt. +#define UART_UARTRIS_CTSRMIS_RESET "-" +#define UART_UARTRIS_CTSRMIS_BITS _u(0x00000002) +#define UART_UARTRIS_CTSRMIS_MSB _u(1) +#define UART_UARTRIS_CTSRMIS_LSB _u(1) +#define UART_UARTRIS_CTSRMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTRIS_RIRMIS +// Description : nUARTRI modem interrupt status. Returns the raw interrupt state +// of the UARTRIINTR interrupt. +#define UART_UARTRIS_RIRMIS_RESET "-" +#define UART_UARTRIS_RIRMIS_BITS _u(0x00000001) +#define UART_UARTRIS_RIRMIS_MSB _u(0) +#define UART_UARTRIS_RIRMIS_LSB _u(0) +#define UART_UARTRIS_RIRMIS_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTMIS +// Description : Masked Interrupt Status Register, UARTMIS +#define UART_UARTMIS_OFFSET _u(0x00000040) +#define UART_UARTMIS_BITS _u(0x000007ff) +#define UART_UARTMIS_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_OEMIS +// Description : Overrun error masked interrupt status. Returns the masked +// interrupt state of the UARTOEINTR interrupt. +#define UART_UARTMIS_OEMIS_RESET _u(0x0) +#define UART_UARTMIS_OEMIS_BITS _u(0x00000400) +#define UART_UARTMIS_OEMIS_MSB _u(10) +#define UART_UARTMIS_OEMIS_LSB _u(10) +#define UART_UARTMIS_OEMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_BEMIS +// Description : Break error masked interrupt status. Returns the masked +// interrupt state of the UARTBEINTR interrupt. +#define UART_UARTMIS_BEMIS_RESET _u(0x0) +#define UART_UARTMIS_BEMIS_BITS _u(0x00000200) +#define UART_UARTMIS_BEMIS_MSB _u(9) +#define UART_UARTMIS_BEMIS_LSB _u(9) +#define UART_UARTMIS_BEMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_PEMIS +// Description : Parity error masked interrupt status. Returns the masked +// interrupt state of the UARTPEINTR interrupt. +#define UART_UARTMIS_PEMIS_RESET _u(0x0) +#define UART_UARTMIS_PEMIS_BITS _u(0x00000100) +#define UART_UARTMIS_PEMIS_MSB _u(8) +#define UART_UARTMIS_PEMIS_LSB _u(8) +#define UART_UARTMIS_PEMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_FEMIS +// Description : Framing error masked interrupt status. Returns the masked +// interrupt state of the UARTFEINTR interrupt. +#define UART_UARTMIS_FEMIS_RESET _u(0x0) +#define UART_UARTMIS_FEMIS_BITS _u(0x00000080) +#define UART_UARTMIS_FEMIS_MSB _u(7) +#define UART_UARTMIS_FEMIS_LSB _u(7) +#define UART_UARTMIS_FEMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_RTMIS +// Description : Receive timeout masked interrupt status. Returns the masked +// interrupt state of the UARTRTINTR interrupt. +#define UART_UARTMIS_RTMIS_RESET _u(0x0) +#define UART_UARTMIS_RTMIS_BITS _u(0x00000040) +#define UART_UARTMIS_RTMIS_MSB _u(6) +#define UART_UARTMIS_RTMIS_LSB _u(6) +#define UART_UARTMIS_RTMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_TXMIS +// Description : Transmit masked interrupt status. Returns the masked interrupt +// state of the UARTTXINTR interrupt. +#define UART_UARTMIS_TXMIS_RESET _u(0x0) +#define UART_UARTMIS_TXMIS_BITS _u(0x00000020) +#define UART_UARTMIS_TXMIS_MSB _u(5) +#define UART_UARTMIS_TXMIS_LSB _u(5) +#define UART_UARTMIS_TXMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_RXMIS +// Description : Receive masked interrupt status. Returns the masked interrupt +// state of the UARTRXINTR interrupt. +#define UART_UARTMIS_RXMIS_RESET _u(0x0) +#define UART_UARTMIS_RXMIS_BITS _u(0x00000010) +#define UART_UARTMIS_RXMIS_MSB _u(4) +#define UART_UARTMIS_RXMIS_LSB _u(4) +#define UART_UARTMIS_RXMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_DSRMMIS +// Description : nUARTDSR modem masked interrupt status. Returns the masked +// interrupt state of the UARTDSRINTR interrupt. +#define UART_UARTMIS_DSRMMIS_RESET "-" +#define UART_UARTMIS_DSRMMIS_BITS _u(0x00000008) +#define UART_UARTMIS_DSRMMIS_MSB _u(3) +#define UART_UARTMIS_DSRMMIS_LSB _u(3) +#define UART_UARTMIS_DSRMMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_DCDMMIS +// Description : nUARTDCD modem masked interrupt status. Returns the masked +// interrupt state of the UARTDCDINTR interrupt. +#define UART_UARTMIS_DCDMMIS_RESET "-" +#define UART_UARTMIS_DCDMMIS_BITS _u(0x00000004) +#define UART_UARTMIS_DCDMMIS_MSB _u(2) +#define UART_UARTMIS_DCDMMIS_LSB _u(2) +#define UART_UARTMIS_DCDMMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_CTSMMIS +// Description : nUARTCTS modem masked interrupt status. Returns the masked +// interrupt state of the UARTCTSINTR interrupt. +#define UART_UARTMIS_CTSMMIS_RESET "-" +#define UART_UARTMIS_CTSMMIS_BITS _u(0x00000002) +#define UART_UARTMIS_CTSMMIS_MSB _u(1) +#define UART_UARTMIS_CTSMMIS_LSB _u(1) +#define UART_UARTMIS_CTSMMIS_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTMIS_RIMMIS +// Description : nUARTRI modem masked interrupt status. Returns the masked +// interrupt state of the UARTRIINTR interrupt. +#define UART_UARTMIS_RIMMIS_RESET "-" +#define UART_UARTMIS_RIMMIS_BITS _u(0x00000001) +#define UART_UARTMIS_RIMMIS_MSB _u(0) +#define UART_UARTMIS_RIMMIS_LSB _u(0) +#define UART_UARTMIS_RIMMIS_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTICR +// Description : Interrupt Clear Register, UARTICR +#define UART_UARTICR_OFFSET _u(0x00000044) +#define UART_UARTICR_BITS _u(0x000007ff) +#define UART_UARTICR_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_OEIC +// Description : Overrun error interrupt clear. Clears the UARTOEINTR interrupt. +#define UART_UARTICR_OEIC_RESET "-" +#define UART_UARTICR_OEIC_BITS _u(0x00000400) +#define UART_UARTICR_OEIC_MSB _u(10) +#define UART_UARTICR_OEIC_LSB _u(10) +#define UART_UARTICR_OEIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_BEIC +// Description : Break error interrupt clear. Clears the UARTBEINTR interrupt. +#define UART_UARTICR_BEIC_RESET "-" +#define UART_UARTICR_BEIC_BITS _u(0x00000200) +#define UART_UARTICR_BEIC_MSB _u(9) +#define UART_UARTICR_BEIC_LSB _u(9) +#define UART_UARTICR_BEIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_PEIC +// Description : Parity error interrupt clear. Clears the UARTPEINTR interrupt. +#define UART_UARTICR_PEIC_RESET "-" +#define UART_UARTICR_PEIC_BITS _u(0x00000100) +#define UART_UARTICR_PEIC_MSB _u(8) +#define UART_UARTICR_PEIC_LSB _u(8) +#define UART_UARTICR_PEIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_FEIC +// Description : Framing error interrupt clear. Clears the UARTFEINTR interrupt. +#define UART_UARTICR_FEIC_RESET "-" +#define UART_UARTICR_FEIC_BITS _u(0x00000080) +#define UART_UARTICR_FEIC_MSB _u(7) +#define UART_UARTICR_FEIC_LSB _u(7) +#define UART_UARTICR_FEIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_RTIC +// Description : Receive timeout interrupt clear. Clears the UARTRTINTR +// interrupt. +#define UART_UARTICR_RTIC_RESET "-" +#define UART_UARTICR_RTIC_BITS _u(0x00000040) +#define UART_UARTICR_RTIC_MSB _u(6) +#define UART_UARTICR_RTIC_LSB _u(6) +#define UART_UARTICR_RTIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_TXIC +// Description : Transmit interrupt clear. Clears the UARTTXINTR interrupt. +#define UART_UARTICR_TXIC_RESET "-" +#define UART_UARTICR_TXIC_BITS _u(0x00000020) +#define UART_UARTICR_TXIC_MSB _u(5) +#define UART_UARTICR_TXIC_LSB _u(5) +#define UART_UARTICR_TXIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_RXIC +// Description : Receive interrupt clear. Clears the UARTRXINTR interrupt. +#define UART_UARTICR_RXIC_RESET "-" +#define UART_UARTICR_RXIC_BITS _u(0x00000010) +#define UART_UARTICR_RXIC_MSB _u(4) +#define UART_UARTICR_RXIC_LSB _u(4) +#define UART_UARTICR_RXIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_DSRMIC +// Description : nUARTDSR modem interrupt clear. Clears the UARTDSRINTR +// interrupt. +#define UART_UARTICR_DSRMIC_RESET "-" +#define UART_UARTICR_DSRMIC_BITS _u(0x00000008) +#define UART_UARTICR_DSRMIC_MSB _u(3) +#define UART_UARTICR_DSRMIC_LSB _u(3) +#define UART_UARTICR_DSRMIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_DCDMIC +// Description : nUARTDCD modem interrupt clear. Clears the UARTDCDINTR +// interrupt. +#define UART_UARTICR_DCDMIC_RESET "-" +#define UART_UARTICR_DCDMIC_BITS _u(0x00000004) +#define UART_UARTICR_DCDMIC_MSB _u(2) +#define UART_UARTICR_DCDMIC_LSB _u(2) +#define UART_UARTICR_DCDMIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_CTSMIC +// Description : nUARTCTS modem interrupt clear. Clears the UARTCTSINTR +// interrupt. +#define UART_UARTICR_CTSMIC_RESET "-" +#define UART_UARTICR_CTSMIC_BITS _u(0x00000002) +#define UART_UARTICR_CTSMIC_MSB _u(1) +#define UART_UARTICR_CTSMIC_LSB _u(1) +#define UART_UARTICR_CTSMIC_ACCESS "WC" +// ----------------------------------------------------------------------------- +// Field : UART_UARTICR_RIMIC +// Description : nUARTRI modem interrupt clear. Clears the UARTRIINTR interrupt. +#define UART_UARTICR_RIMIC_RESET "-" +#define UART_UARTICR_RIMIC_BITS _u(0x00000001) +#define UART_UARTICR_RIMIC_MSB _u(0) +#define UART_UARTICR_RIMIC_LSB _u(0) +#define UART_UARTICR_RIMIC_ACCESS "WC" +// ============================================================================= +// Register : UART_UARTDMACR +// Description : DMA Control Register, UARTDMACR +#define UART_UARTDMACR_OFFSET _u(0x00000048) +#define UART_UARTDMACR_BITS _u(0x00000007) +#define UART_UARTDMACR_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTDMACR_DMAONERR +// Description : DMA on error. If this bit is set to 1, the DMA receive request +// outputs, UARTRXDMASREQ or UARTRXDMABREQ, are disabled when the +// UART error interrupt is asserted. +#define UART_UARTDMACR_DMAONERR_RESET _u(0x0) +#define UART_UARTDMACR_DMAONERR_BITS _u(0x00000004) +#define UART_UARTDMACR_DMAONERR_MSB _u(2) +#define UART_UARTDMACR_DMAONERR_LSB _u(2) +#define UART_UARTDMACR_DMAONERR_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDMACR_TXDMAE +// Description : Transmit DMA enable. If this bit is set to 1, DMA for the +// transmit FIFO is enabled. +#define UART_UARTDMACR_TXDMAE_RESET _u(0x0) +#define UART_UARTDMACR_TXDMAE_BITS _u(0x00000002) +#define UART_UARTDMACR_TXDMAE_MSB _u(1) +#define UART_UARTDMACR_TXDMAE_LSB _u(1) +#define UART_UARTDMACR_TXDMAE_ACCESS "RW" +// ----------------------------------------------------------------------------- +// Field : UART_UARTDMACR_RXDMAE +// Description : Receive DMA enable. If this bit is set to 1, DMA for the +// receive FIFO is enabled. +#define UART_UARTDMACR_RXDMAE_RESET _u(0x0) +#define UART_UARTDMACR_RXDMAE_BITS _u(0x00000001) +#define UART_UARTDMACR_RXDMAE_MSB _u(0) +#define UART_UARTDMACR_RXDMAE_LSB _u(0) +#define UART_UARTDMACR_RXDMAE_ACCESS "RW" +// ============================================================================= +// Register : UART_UARTPERIPHID0 +// Description : UARTPeriphID0 Register +#define UART_UARTPERIPHID0_OFFSET _u(0x00000fe0) +#define UART_UARTPERIPHID0_BITS _u(0x000000ff) +#define UART_UARTPERIPHID0_RESET _u(0x00000011) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID0_PARTNUMBER0 +// Description : These bits read back as 0x11 +#define UART_UARTPERIPHID0_PARTNUMBER0_RESET _u(0x11) +#define UART_UARTPERIPHID0_PARTNUMBER0_BITS _u(0x000000ff) +#define UART_UARTPERIPHID0_PARTNUMBER0_MSB _u(7) +#define UART_UARTPERIPHID0_PARTNUMBER0_LSB _u(0) +#define UART_UARTPERIPHID0_PARTNUMBER0_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPERIPHID1 +// Description : UARTPeriphID1 Register +#define UART_UARTPERIPHID1_OFFSET _u(0x00000fe4) +#define UART_UARTPERIPHID1_BITS _u(0x000000ff) +#define UART_UARTPERIPHID1_RESET _u(0x00000010) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID1_DESIGNER0 +// Description : These bits read back as 0x1 +#define UART_UARTPERIPHID1_DESIGNER0_RESET _u(0x1) +#define UART_UARTPERIPHID1_DESIGNER0_BITS _u(0x000000f0) +#define UART_UARTPERIPHID1_DESIGNER0_MSB _u(7) +#define UART_UARTPERIPHID1_DESIGNER0_LSB _u(4) +#define UART_UARTPERIPHID1_DESIGNER0_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID1_PARTNUMBER1 +// Description : These bits read back as 0x0 +#define UART_UARTPERIPHID1_PARTNUMBER1_RESET _u(0x0) +#define UART_UARTPERIPHID1_PARTNUMBER1_BITS _u(0x0000000f) +#define UART_UARTPERIPHID1_PARTNUMBER1_MSB _u(3) +#define UART_UARTPERIPHID1_PARTNUMBER1_LSB _u(0) +#define UART_UARTPERIPHID1_PARTNUMBER1_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPERIPHID2 +// Description : UARTPeriphID2 Register +#define UART_UARTPERIPHID2_OFFSET _u(0x00000fe8) +#define UART_UARTPERIPHID2_BITS _u(0x000000ff) +#define UART_UARTPERIPHID2_RESET _u(0x00000034) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID2_REVISION +// Description : This field depends on the revision of the UART: r1p0 0x0 r1p1 +// 0x1 r1p3 0x2 r1p4 0x2 r1p5 0x3 +#define UART_UARTPERIPHID2_REVISION_RESET _u(0x3) +#define UART_UARTPERIPHID2_REVISION_BITS _u(0x000000f0) +#define UART_UARTPERIPHID2_REVISION_MSB _u(7) +#define UART_UARTPERIPHID2_REVISION_LSB _u(4) +#define UART_UARTPERIPHID2_REVISION_ACCESS "RO" +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID2_DESIGNER1 +// Description : These bits read back as 0x4 +#define UART_UARTPERIPHID2_DESIGNER1_RESET _u(0x4) +#define UART_UARTPERIPHID2_DESIGNER1_BITS _u(0x0000000f) +#define UART_UARTPERIPHID2_DESIGNER1_MSB _u(3) +#define UART_UARTPERIPHID2_DESIGNER1_LSB _u(0) +#define UART_UARTPERIPHID2_DESIGNER1_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPERIPHID3 +// Description : UARTPeriphID3 Register +#define UART_UARTPERIPHID3_OFFSET _u(0x00000fec) +#define UART_UARTPERIPHID3_BITS _u(0x000000ff) +#define UART_UARTPERIPHID3_RESET _u(0x00000000) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPERIPHID3_CONFIGURATION +// Description : These bits read back as 0x00 +#define UART_UARTPERIPHID3_CONFIGURATION_RESET _u(0x00) +#define UART_UARTPERIPHID3_CONFIGURATION_BITS _u(0x000000ff) +#define UART_UARTPERIPHID3_CONFIGURATION_MSB _u(7) +#define UART_UARTPERIPHID3_CONFIGURATION_LSB _u(0) +#define UART_UARTPERIPHID3_CONFIGURATION_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPCELLID0 +// Description : UARTPCellID0 Register +#define UART_UARTPCELLID0_OFFSET _u(0x00000ff0) +#define UART_UARTPCELLID0_BITS _u(0x000000ff) +#define UART_UARTPCELLID0_RESET _u(0x0000000d) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPCELLID0_UARTPCELLID0 +// Description : These bits read back as 0x0D +#define UART_UARTPCELLID0_UARTPCELLID0_RESET _u(0x0d) +#define UART_UARTPCELLID0_UARTPCELLID0_BITS _u(0x000000ff) +#define UART_UARTPCELLID0_UARTPCELLID0_MSB _u(7) +#define UART_UARTPCELLID0_UARTPCELLID0_LSB _u(0) +#define UART_UARTPCELLID0_UARTPCELLID0_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPCELLID1 +// Description : UARTPCellID1 Register +#define UART_UARTPCELLID1_OFFSET _u(0x00000ff4) +#define UART_UARTPCELLID1_BITS _u(0x000000ff) +#define UART_UARTPCELLID1_RESET _u(0x000000f0) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPCELLID1_UARTPCELLID1 +// Description : These bits read back as 0xF0 +#define UART_UARTPCELLID1_UARTPCELLID1_RESET _u(0xf0) +#define UART_UARTPCELLID1_UARTPCELLID1_BITS _u(0x000000ff) +#define UART_UARTPCELLID1_UARTPCELLID1_MSB _u(7) +#define UART_UARTPCELLID1_UARTPCELLID1_LSB _u(0) +#define UART_UARTPCELLID1_UARTPCELLID1_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPCELLID2 +// Description : UARTPCellID2 Register +#define UART_UARTPCELLID2_OFFSET _u(0x00000ff8) +#define UART_UARTPCELLID2_BITS _u(0x000000ff) +#define UART_UARTPCELLID2_RESET _u(0x00000005) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPCELLID2_UARTPCELLID2 +// Description : These bits read back as 0x05 +#define UART_UARTPCELLID2_UARTPCELLID2_RESET _u(0x05) +#define UART_UARTPCELLID2_UARTPCELLID2_BITS _u(0x000000ff) +#define UART_UARTPCELLID2_UARTPCELLID2_MSB _u(7) +#define UART_UARTPCELLID2_UARTPCELLID2_LSB _u(0) +#define UART_UARTPCELLID2_UARTPCELLID2_ACCESS "RO" +// ============================================================================= +// Register : UART_UARTPCELLID3 +// Description : UARTPCellID3 Register +#define UART_UARTPCELLID3_OFFSET _u(0x00000ffc) +#define UART_UARTPCELLID3_BITS _u(0x000000ff) +#define UART_UARTPCELLID3_RESET _u(0x000000b1) +// ----------------------------------------------------------------------------- +// Field : UART_UARTPCELLID3_UARTPCELLID3 +// Description : These bits read back as 0xB1 +#define UART_UARTPCELLID3_UARTPCELLID3_RESET _u(0xb1) +#define UART_UARTPCELLID3_UARTPCELLID3_BITS _u(0x000000ff) +#define UART_UARTPCELLID3_UARTPCELLID3_MSB _u(7) +#define UART_UARTPCELLID3_UARTPCELLID3_LSB _u(0) +#define UART_UARTPCELLID3_UARTPCELLID3_ACCESS "RO" +// ============================================================================= +#endif // _HARDWARE_REGS_UART_H + |