diff options
Diffstat (limited to 'lib/hal-stm32f1/source/stm32f1xx_hal_nand.c')
| -rw-r--r-- | lib/hal-stm32f1/source/stm32f1xx_hal_nand.c | 1804 |
1 files changed, 1804 insertions, 0 deletions
diff --git a/lib/hal-stm32f1/source/stm32f1xx_hal_nand.c b/lib/hal-stm32f1/source/stm32f1xx_hal_nand.c new file mode 100644 index 00000000..85ad5085 --- /dev/null +++ b/lib/hal-stm32f1/source/stm32f1xx_hal_nand.c @@ -0,0 +1,1804 @@ +/**
+ ******************************************************************************
+ * @file stm32f1xx_hal_nand.c
+ * @author MCD Application Team
+ * @version V1.1.1
+ * @date 12-May-2017
+ * @brief NAND HAL module driver.
+ * This file provides a generic firmware to drive NAND memories mounted
+ * as external device.
+ *
+ @verbatim
+ ==============================================================================
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+ This driver is a generic layered driver which contains a set of APIs used to
+ control NAND flash memories. It uses the FSMC layer functions to interface
+ with NAND devices. This driver is used as follows:
+
+ (+) NAND flash memory configuration sequence using the function HAL_NAND_Init()
+ with control and timing parameters for both common and attribute spaces.
+
+ (+) Read NAND flash memory maker and device IDs using the function
+ HAL_NAND_Read_ID(). The read information is stored in the NAND_ID_TypeDef
+ structure declared by the function caller.
+
+ (+) Access NAND flash memory by read/write operations using the functions
+ HAL_NAND_Read_Page_8b()/HAL_NAND_Read_SpareArea_8b(),
+ HAL_NAND_Write_Page_8b()/HAL_NAND_Write_SpareArea_8b(),
+ HAL_NAND_Read_Page_16b()/HAL_NAND_Read_SpareArea_16b(),
+ HAL_NAND_Write_Page_16b()/HAL_NAND_Write_SpareArea_16b()
+ to read/write page(s)/spare area(s). These functions use specific device
+ information (Block, page size..) predefined by the user in the NAND_DeviceConfigTypeDef
+ structure. The read/write address information is contained by the Nand_Address_Typedef
+ structure passed as parameter.
+
+ (+) Perform NAND flash Reset chip operation using the function HAL_NAND_Reset().
+
+ (+) Perform NAND flash erase block operation using the function HAL_NAND_Erase_Block().
+ The erase block address information is contained in the Nand_Address_Typedef
+ structure passed as parameter.
+
+ (+) Read the NAND flash status operation using the function HAL_NAND_Read_Status().
+
+ (+) You can also control the NAND device by calling the control APIs HAL_NAND_ECC_Enable()/
+ HAL_NAND_ECC_Disable() to respectively enable/disable the ECC code correction
+ feature or the function HAL_NAND_GetECC() to get the ECC correction code.
+
+ (+) You can monitor the NAND device HAL state by calling the function
+ HAL_NAND_GetState()
+
+ [..]
+ (@) This driver is a set of generic APIs which handle standard NAND flash operations.
+ If a NAND flash device contains different operations and/or implementations,
+ it should be implemented separately.
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+ * @{
+ */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+
+#if defined (STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG) || defined(STM32F103xG)
+
+/** @defgroup NAND NAND
+ * @brief NAND HAL module driver
+ * @{
+ */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup NAND_Private_Constants NAND Private Constants
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup NAND_Private_Macros NAND Private Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup NAND_Exported_Functions NAND Exported Functions
+ * @{
+ */
+
+/** @defgroup NAND_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### NAND Initialization and de-initialization functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to initialize/de-initialize
+ the NAND memory
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Perform NAND memory Initialization sequence
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param ComSpace_Timing: pointer to Common space timing structure
+ * @param AttSpace_Timing: pointer to Attribute space timing structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Init(NAND_HandleTypeDef *hnand, FSMC_NAND_PCC_TimingTypeDef *ComSpace_Timing, FSMC_NAND_PCC_TimingTypeDef *AttSpace_Timing)
+{
+ /* Check the NAND handle state */
+ if(hnand == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ if(hnand->State == HAL_NAND_STATE_RESET)
+ {
+ /* Allocate lock resource and initialize it */
+ hnand->Lock = HAL_UNLOCKED;
+ /* Initialize the low level hardware (MSP) */
+ HAL_NAND_MspInit(hnand);
+ }
+
+ /* Initialize NAND control Interface */
+ FSMC_NAND_Init(hnand->Instance, &(hnand->Init));
+
+ /* Initialize NAND common space timing Interface */
+ FSMC_NAND_CommonSpace_Timing_Init(hnand->Instance, ComSpace_Timing, hnand->Init.NandBank);
+
+ /* Initialize NAND attribute space timing Interface */
+ FSMC_NAND_AttributeSpace_Timing_Init(hnand->Instance, AttSpace_Timing, hnand->Init.NandBank);
+
+ /* Enable the NAND device */
+ __FSMC_NAND_ENABLE(hnand->Instance, hnand->Init.NandBank);
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Perform NAND memory De-Initialization sequence
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_DeInit(NAND_HandleTypeDef *hnand)
+{
+ /* Initialize the low level hardware (MSP) */
+ HAL_NAND_MspDeInit(hnand);
+
+ /* Configure the NAND registers with their reset values */
+ FSMC_NAND_DeInit(hnand->Instance, hnand->Init.NandBank);
+
+ /* Reset the NAND controller state */
+ hnand->State = HAL_NAND_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief NAND MSP Init
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval None
+ */
+__weak void HAL_NAND_MspInit(NAND_HandleTypeDef *hnand)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hnand);
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_NAND_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief NAND MSP DeInit
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval None
+ */
+__weak void HAL_NAND_MspDeInit(NAND_HandleTypeDef *hnand)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hnand);
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_NAND_MspDeInit could be implemented in the user file
+ */
+}
+
+
+/**
+ * @brief This function handles NAND device interrupt request.
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL status
+*/
+void HAL_NAND_IRQHandler(NAND_HandleTypeDef *hnand)
+{
+ /* Check NAND interrupt Rising edge flag */
+ if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_RISING_EDGE))
+ {
+ /* NAND interrupt callback*/
+ HAL_NAND_ITCallback(hnand);
+
+ /* Clear NAND interrupt Rising edge pending bit */
+ __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_RISING_EDGE);
+ }
+
+ /* Check NAND interrupt Level flag */
+ if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_LEVEL))
+ {
+ /* NAND interrupt callback*/
+ HAL_NAND_ITCallback(hnand);
+
+ /* Clear NAND interrupt Level pending bit */
+ __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_LEVEL);
+ }
+
+ /* Check NAND interrupt Falling edge flag */
+ if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FALLING_EDGE))
+ {
+ /* NAND interrupt callback*/
+ HAL_NAND_ITCallback(hnand);
+
+ /* Clear NAND interrupt Falling edge pending bit */
+ __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FALLING_EDGE);
+ }
+
+ /* Check NAND interrupt FIFO empty flag */
+ if(__FSMC_NAND_GET_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FEMPT))
+ {
+ /* NAND interrupt callback*/
+ HAL_NAND_ITCallback(hnand);
+
+ /* Clear NAND interrupt FIFO empty pending bit */
+ __FSMC_NAND_CLEAR_FLAG(hnand->Instance, hnand->Init.NandBank, FSMC_FLAG_FEMPT);
+ }
+}
+
+/**
+ * @brief NAND interrupt feature callback
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval None
+ */
+__weak void HAL_NAND_ITCallback(NAND_HandleTypeDef *hnand)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hnand);
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_NAND_ITCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup NAND_Exported_Functions_Group2 Input and Output functions
+ * @brief Input Output and memory control functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### NAND Input and Output functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to use and control the NAND
+ memory
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Read the NAND memory electronic signature
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pNAND_ID: NAND ID structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Read_ID(NAND_HandleTypeDef *hnand, NAND_IDTypeDef *pNAND_ID)
+{
+ __IO uint32_t data = 0U;
+ __IO uint32_t data1 = 0U;
+ uint32_t deviceaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Send Read ID command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_READID;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+
+ /* Read the electronic signature from NAND flash */
+ if (hnand->Init.MemoryDataWidth == FSMC_NAND_PCC_MEM_BUS_WIDTH_8)
+ {
+ data = *(__IO uint32_t *)deviceaddress;
+
+ /* Return the data read */
+ pNAND_ID->Maker_Id = ADDR_1ST_CYCLE(data);
+ pNAND_ID->Device_Id = ADDR_2ND_CYCLE(data);
+ pNAND_ID->Third_Id = ADDR_3RD_CYCLE(data);
+ pNAND_ID->Fourth_Id = ADDR_4TH_CYCLE(data);
+ }
+ else
+ {
+ data = *(__IO uint32_t *)deviceaddress;
+ data1 = *((__IO uint32_t *)deviceaddress + 4U);
+
+ /* Return the data read */
+ pNAND_ID->Maker_Id = ADDR_1ST_CYCLE(data);
+ pNAND_ID->Device_Id = ADDR_3RD_CYCLE(data);
+ pNAND_ID->Third_Id = ADDR_1ST_CYCLE(data1);
+ pNAND_ID->Fourth_Id = ADDR_3RD_CYCLE(data1);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief NAND memory reset
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Reset(NAND_HandleTypeDef *hnand)
+{
+ uint32_t deviceaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Send NAND reset command */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = 0xFF;
+
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+
+}
+
+/**
+ * @brief Configure the device: Enter the physical parameters of the device
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pDeviceConfig : pointer to NAND_DeviceConfigTypeDef structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_ConfigDevice(NAND_HandleTypeDef *hnand, NAND_DeviceConfigTypeDef *pDeviceConfig)
+{
+ hnand->Config.PageSize = pDeviceConfig->PageSize;
+ hnand->Config.SpareAreaSize = pDeviceConfig->SpareAreaSize;
+ hnand->Config.BlockSize = pDeviceConfig->BlockSize;
+ hnand->Config.BlockNbr = pDeviceConfig->BlockNbr;
+ hnand->Config.PlaneSize = pDeviceConfig->PlaneSize;
+ hnand->Config.PlaneNbr = pDeviceConfig->PlaneNbr;
+ hnand->Config.ExtraCommandEnable = pDeviceConfig->ExtraCommandEnable;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Read Page(s) from NAND memory block (8-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to destination read buffer
+ * @param NumPageToRead : number of pages to read from block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Read_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumPageToRead)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numPagesRead = 0U, nandaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Page(s) read loop */
+ while((NumPageToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesRead);
+
+ /* Send read page command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
+
+ /* Check if an extra command is needed for reading pages */
+ if(hnand->Config.ExtraCommandEnable == ENABLE)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Go back to read mode */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
+ }
+
+ /* Get Data into Buffer */
+ for(; index < size; index++)
+ {
+ *(uint8_t *)pBuffer++ = *(uint8_t *)deviceaddress;
+ }
+
+ /* Increment read pages number */
+ numPagesRead++;
+
+ /* Decrement pages to read */
+ NumPageToRead--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Read Page(s) from NAND memory block (16-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to destination read buffer. pBuffer should be 16bits aligned
+ * @param NumPageToRead : number of pages to read from block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Read_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumPageToRead)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numPagesRead = 0U, nandaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Page(s) read loop */
+ while((NumPageToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesRead);
+
+ /* Send read page command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
+
+ if(hnand->Config.ExtraCommandEnable == ENABLE)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Go back to read mode */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
+ }
+
+ /* Get Data into Buffer */
+ for(; index < size; index++)
+ {
+ *(uint16_t *)pBuffer++ = *(uint16_t *)deviceaddress;
+ }
+
+ /* Increment read pages number */
+ numPagesRead++;
+
+ /* Decrement pages to read */
+ NumPageToRead--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Write Page(s) to NAND memory block (8-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to source buffer to write
+ * @param NumPageToWrite : number of pages to write to block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Write_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumPageToWrite)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numPagesWritten = 0U, nandaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Page(s) write loop */
+ while((NumPageToWrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = hnand->Config.PageSize + ((hnand->Config.PageSize) * numPagesWritten);
+
+ /* Send write page command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+
+ /* Write data to memory */
+ for(; index < size; index++)
+ {
+ *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Increment written pages number */
+ numPagesWritten++;
+
+ /* Decrement pages to write */
+ NumPageToWrite--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Write Page(s) to NAND memory block (16-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to source buffer to write. pBuffer should be 16bits aligned
+ * @param NumPageToWrite : number of pages to write to block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Write_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumPageToWrite)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numPagesWritten = 0U, nandaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Page(s) write loop */
+ while((NumPageToWrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.PageSize) + ((hnand->Config.PageSize) * numPagesWritten);
+
+ /* Send write page command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ /* Write data to memory */
+ for(; index < size; index++)
+ {
+ *(__IO uint16_t *)deviceaddress = *(uint16_t *)pBuffer++;
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Increment written pages number */
+ numPagesWritten++;
+
+ /* Decrement pages to write */
+ NumPageToWrite--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Read Spare area(s) from NAND memory (8-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer: pointer to source buffer to write
+ * @param NumSpareAreaToRead: Number of spare area to read
+ * @retval HAL status
+*/
+HAL_StatusTypeDef HAL_NAND_Read_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaToRead)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numSpareAreaRead = 0U, nandaddress = 0U, columnaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Column in page address */
+ columnaddress = COLUMN_ADDRESS(hnand);
+
+ /* Spare area(s) read loop */
+ while((NumSpareAreaToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaRead);
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ /* Send read spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ /* Send read spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
+
+ if(hnand->Config.ExtraCommandEnable == ENABLE)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Go back to read mode */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
+ }
+
+ /* Get Data into Buffer */
+ for(; index < size; index++)
+ {
+ *(uint8_t *)pBuffer++ = *(uint8_t *)deviceaddress;
+ }
+
+ /* Increment read spare areas number */
+ numSpareAreaRead++;
+
+ /* Decrement spare areas to read */
+ NumSpareAreaToRead--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Read Spare area(s) from NAND memory (16-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer: pointer to source buffer to write. pBuffer should be 16bits aligned.
+ * @param NumSpareAreaToRead: Number of spare area to read
+ * @retval HAL status
+*/
+HAL_StatusTypeDef HAL_NAND_Read_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumSpareAreaToRead)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numSpareAreaRead = 0U, nandaddress = 0U, columnaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Column in page address */
+ columnaddress = (uint32_t)(COLUMN_ADDRESS(hnand) * 2U);
+
+ /* Spare area(s) read loop */
+ while((NumSpareAreaToRead != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaRead);
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ /* Send read spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ /* Send read spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
+
+ if(hnand->Config.ExtraCommandEnable == ENABLE)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Go back to read mode */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = ((uint8_t)0x00);
+ }
+
+ /* Get Data into Buffer */
+ for(; index < size; index++)
+ {
+ *(uint16_t *)pBuffer++ = *(uint16_t *)deviceaddress;
+ }
+
+ /* Increment read spare areas number */
+ numSpareAreaRead++;
+
+ /* Decrement spare areas to read */
+ NumSpareAreaToRead--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Write Spare area(s) to NAND memory (8-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to source buffer to write
+ * @param NumSpareAreaTowrite : number of spare areas to write to block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Write_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaTowrite)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numSpareAreaWritten = 0U, nandaddress = 0U, columnaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the FSMC_NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Page address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Column in page address */
+ columnaddress = COLUMN_ADDRESS(hnand);
+
+ /* Spare area(s) write loop */
+ while((NumSpareAreaTowrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaWritten);
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ /* Send write Spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ /* Send write Spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ /* Write data to memory */
+ for(; index < size; index++)
+ {
+ *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Increment written spare areas number */
+ numSpareAreaWritten++;
+
+ /* Decrement spare areas to write */
+ NumSpareAreaTowrite--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Write Spare area(s) to NAND memory (16-bits addressing)
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @param pBuffer : pointer to source buffer to write. pBuffer should be 16bits aligned.
+ * @param NumSpareAreaTowrite : number of spare areas to write to block
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Write_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer, uint32_t NumSpareAreaTowrite)
+{
+ __IO uint32_t index = 0U;
+ uint32_t tickstart = 0U;
+ uint32_t deviceaddress = 0U, size = 0U, numSpareAreaWritten = 0U, nandaddress = 0U, columnaddress = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the FSMC_NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* NAND raw address calculation */
+ nandaddress = ARRAY_ADDRESS(pAddress, hnand);
+
+ /* Column in page address */
+ columnaddress = (uint32_t)(COLUMN_ADDRESS(hnand) * 2U);
+
+ /* Spare area(s) write loop */
+ while((NumSpareAreaTowrite != 0U) && (nandaddress < ((hnand->Config.BlockSize) * (hnand->Config.BlockNbr))))
+ {
+ /* update the buffer size */
+ size = (hnand->Config.SpareAreaSize) + ((hnand->Config.SpareAreaSize) * numSpareAreaWritten);
+
+ /* Cards with page size <= 512 bytes */
+ if((hnand->Config.PageSize) <= 512U)
+ {
+ /* Send write Spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+ else /* (hnand->Config.PageSize) > 512 */
+ {
+ /* Send write Spare area command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_A;
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;
+
+ if (((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) <= 65535U)
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ }
+ else /* ((hnand->Config.BlockSize)*(hnand->Config.BlockNbr)) > 65535 */
+ {
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_1ST_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = COLUMN_2ND_CYCLE(columnaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(nandaddress);
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(nandaddress);
+ }
+ }
+
+ /* Write data to memory */
+ for(; index < size; index++)
+ {
+ *(__IO uint16_t *)deviceaddress = *(uint16_t *)pBuffer++;
+ }
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Increment written spare areas number */
+ numSpareAreaWritten++;
+
+ /* Decrement spare areas to write */
+ NumSpareAreaTowrite--;
+
+ /* Increment the NAND address */
+ nandaddress = (uint32_t)(nandaddress + 1U);
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief NAND memory Block erase
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress : pointer to NAND address structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_Erase_Block(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
+{
+ uint32_t deviceaddress = 0U;
+ uint32_t tickstart = 0U;
+
+ /* Process Locked */
+ __HAL_LOCK(hnand);
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Send Erase block command sequence */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE0;
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
+
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE1;
+
+ /* Update the NAND controller state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ /* Get tick */
+ tickstart = HAL_GetTick();
+
+ /* Read status until NAND is ready */
+ while(HAL_NAND_Read_Status(hnand) != NAND_READY)
+ {
+ if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
+ {
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hnand);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief NAND memory read status
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval NAND status
+ */
+uint32_t HAL_NAND_Read_Status(NAND_HandleTypeDef *hnand)
+{
+ uint32_t data = 0U;
+ uint32_t deviceaddress = 0U;
+
+ /* Identify the device address */
+ if(hnand->Init.NandBank == FSMC_NAND_BANK2)
+ {
+ deviceaddress = NAND_DEVICE1;
+ }
+ else
+ {
+ deviceaddress = NAND_DEVICE2;
+ }
+
+ /* Send Read status operation command */
+ *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_STATUS;
+
+ /* Read status register data */
+ data = *(__IO uint8_t *)deviceaddress;
+
+ /* Return the status */
+ if((data & NAND_ERROR) == NAND_ERROR)
+ {
+ return NAND_ERROR;
+ }
+ else if((data & NAND_READY) == NAND_READY)
+ {
+ return NAND_READY;
+ }
+
+ return NAND_BUSY;
+}
+
+/**
+ * @brief Increment the NAND memory address
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param pAddress: pointer to NAND address structure
+ * @retval The new status of the increment address operation. It can be:
+ * - NAND_VALID_ADDRESS: When the new address is valid address
+ * - NAND_INVALID_ADDRESS: When the new address is invalid address
+ */
+uint32_t HAL_NAND_Address_Inc(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
+{
+ uint32_t status = NAND_VALID_ADDRESS;
+
+ /* Increment page address */
+ pAddress->Page++;
+
+ /* Check NAND address is valid */
+ if(pAddress->Page == hnand->Config.BlockSize)
+ {
+ pAddress->Page = 0U;
+ pAddress->Block++;
+
+ if(pAddress->Block == hnand->Config.PlaneSize)
+ {
+ pAddress->Block = 0U;
+ pAddress->Plane++;
+
+ if(pAddress->Plane == (hnand->Config.PlaneNbr))
+ {
+ status = NAND_INVALID_ADDRESS;
+ }
+ }
+ }
+
+ return (status);
+}
+/**
+ * @}
+ */
+
+/** @defgroup NAND_Exported_Functions_Group3 Peripheral Control functions
+ * @brief management functions
+ *
+@verbatim
+ ==============================================================================
+ ##### NAND Control functions #####
+ ==============================================================================
+ [..]
+ This subsection provides a set of functions allowing to control dynamically
+ the NAND interface.
+
+@endverbatim
+ * @{
+ */
+
+
+/**
+ * @brief Enables dynamically NAND ECC feature.
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_ECC_Enable(NAND_HandleTypeDef *hnand)
+{
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Enable ECC feature */
+ FSMC_NAND_ECC_Enable(hnand->Instance, hnand->Init.NandBank);
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Disables dynamically FSMC_NAND ECC feature.
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_ECC_Disable(NAND_HandleTypeDef *hnand)
+{
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Disable ECC feature */
+ FSMC_NAND_ECC_Disable(hnand->Instance, hnand->Init.NandBank);
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Disables dynamically NAND ECC feature.
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @param ECCval: pointer to ECC value
+ * @param Timeout: maximum timeout to wait
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_NAND_GetECC(NAND_HandleTypeDef *hnand, uint32_t *ECCval, uint32_t Timeout)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ /* Check the NAND controller state */
+ if(hnand->State == HAL_NAND_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_BUSY;
+
+ /* Get NAND ECC value */
+ status = FSMC_NAND_GetECC(hnand->Instance, ECCval, hnand->Init.NandBank, Timeout);
+
+ /* Update the NAND state */
+ hnand->State = HAL_NAND_STATE_READY;
+
+ return status;
+}
+
+/**
+ * @}
+ */
+
+
+/** @defgroup NAND_Exported_Functions_Group4 Peripheral State functions
+ * @brief Peripheral State functions
+ *
+@verbatim
+ ==============================================================================
+ ##### NAND State functions #####
+ ==============================================================================
+ [..]
+ This subsection permits to get in run-time the status of the NAND controller
+ and the data flow.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief return the NAND state
+ * @param hnand: pointer to a NAND_HandleTypeDef structure that contains
+ * the configuration information for NAND module.
+ * @retval HAL state
+ */
+HAL_NAND_StateTypeDef HAL_NAND_GetState(NAND_HandleTypeDef *hnand)
+{
+ return hnand->State;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* STM32F101xE || STM32F103xE || STM32F101xG || STM32F103xG */
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|