diff options
Diffstat (limited to 'lib/hal-stm32f1/include/stm32f1xx_ll_sdmmc.h')
| -rw-r--r-- | lib/hal-stm32f1/include/stm32f1xx_ll_sdmmc.h | 1127 |
1 files changed, 1127 insertions, 0 deletions
diff --git a/lib/hal-stm32f1/include/stm32f1xx_ll_sdmmc.h b/lib/hal-stm32f1/include/stm32f1xx_ll_sdmmc.h new file mode 100644 index 00000000..8a455133 --- /dev/null +++ b/lib/hal-stm32f1/include/stm32f1xx_ll_sdmmc.h @@ -0,0 +1,1127 @@ +/**
+ ******************************************************************************
+ * @file stm32f1xx_ll_sdmmc.h
+ * @author MCD Application Team
+ * @version V1.1.1
+ * @date 12-May-2017
+ * @brief Header file of low layer SDMMC HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __stm32f1xx_LL_SD_H
+#define __stm32f1xx_LL_SD_H
+
+#if defined(STM32F103xE) || defined(STM32F103xG)
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup SDMMC_LL
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup SDMMC_LL_Exported_Types SDMMC_LL Exported Types
+ * @{
+ */
+
+/**
+ * @brief SDMMC Configuration Structure definition
+ */
+typedef struct
+{
+ uint32_t ClockEdge; /*!< Specifies the clock transition on which the bit capture is made.
+ This parameter can be a value of @ref SDMMC_LL_Clock_Edge */
+
+ uint32_t ClockBypass; /*!< Specifies whether the SDIO Clock divider bypass is
+ enabled or disabled.
+ This parameter can be a value of @ref SDMMC_LL_Clock_Bypass */
+
+ uint32_t ClockPowerSave; /*!< Specifies whether SDIO Clock output is enabled or
+ disabled when the bus is idle.
+ This parameter can be a value of @ref SDMMC_LL_Clock_Power_Save */
+
+ uint32_t BusWide; /*!< Specifies the SDIO bus width.
+ This parameter can be a value of @ref SDMMC_LL_Bus_Wide */
+
+ uint32_t HardwareFlowControl; /*!< Specifies whether the SDIO hardware flow control is enabled or disabled.
+ This parameter can be a value of @ref SDMMC_LL_Hardware_Flow_Control */
+
+ uint32_t ClockDiv; /*!< Specifies the clock frequency of the SDIO controller.
+ This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
+
+}SDIO_InitTypeDef;
+
+
+/**
+ * @brief SDIO Command Control structure
+ */
+typedef struct
+{
+ uint32_t Argument; /*!< Specifies the SDIO command argument which is sent
+ to a card as part of a command message. If a command
+ contains an argument, it must be loaded into this register
+ before writing the command to the command register. */
+
+ uint32_t CmdIndex; /*!< Specifies the SDIO command index. It must be Min_Data = 0 and
+ Max_Data = 64 */
+
+ uint32_t Response; /*!< Specifies the SDIO response type.
+ This parameter can be a value of @ref SDMMC_LL_Response_Type */
+
+ uint32_t WaitForInterrupt; /*!< Specifies whether SDIO wait for interrupt request is
+ enabled or disabled.
+ This parameter can be a value of @ref SDMMC_LL_Wait_Interrupt_State */
+
+ uint32_t CPSM; /*!< Specifies whether SDIO Command path state machine (CPSM)
+ is enabled or disabled.
+ This parameter can be a value of @ref SDMMC_LL_CPSM_State */
+}SDIO_CmdInitTypeDef;
+
+
+/**
+ * @brief SDIO Data Control structure
+ */
+typedef struct
+{
+ uint32_t DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */
+
+ uint32_t DataLength; /*!< Specifies the number of data bytes to be transferred. */
+
+ uint32_t DataBlockSize; /*!< Specifies the data block size for block transfer.
+ This parameter can be a value of @ref SDMMC_LL_Data_Block_Size */
+
+ uint32_t TransferDir; /*!< Specifies the data transfer direction, whether the transfer
+ is a read or write.
+ This parameter can be a value of @ref SDMMC_LL_Transfer_Direction */
+
+ uint32_t TransferMode; /*!< Specifies whether data transfer is in stream or block mode.
+ This parameter can be a value of @ref SDMMC_LL_Transfer_Type */
+
+ uint32_t DPSM; /*!< Specifies whether SDIO Data path state machine (DPSM)
+ is enabled or disabled.
+ This parameter can be a value of @ref SDMMC_LL_DPSM_State */
+}SDIO_DataInitTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SDMMC_LL_Exported_Constants SDMMC_LL Exported Constants
+ * @{
+ */
+#define SDMMC_ERROR_NONE 0x00000000U /*!< No error */
+#define SDMMC_ERROR_CMD_CRC_FAIL 0x00000001U /*!< Command response received (but CRC check failed) */
+#define SDMMC_ERROR_DATA_CRC_FAIL 0x00000002U /*!< Data block sent/received (CRC check failed) */
+#define SDMMC_ERROR_CMD_RSP_TIMEOUT 0x00000004U /*!< Command response timeout */
+#define SDMMC_ERROR_DATA_TIMEOUT 0x00000008U /*!< Data timeout */
+#define SDMMC_ERROR_TX_UNDERRUN 0x00000010U /*!< Transmit FIFO underrun */
+#define SDMMC_ERROR_RX_OVERRUN 0x00000020U /*!< Receive FIFO overrun */
+#define SDMMC_ERROR_ADDR_MISALIGNED 0x00000040U /*!< Misaligned address */
+#define SDMMC_ERROR_BLOCK_LEN_ERR 0x00000080U /*!< Transferred block length is not allowed for the card or the
+ number of transferred bytes does not match the block length */
+#define SDMMC_ERROR_ERASE_SEQ_ERR 0x00000100U /*!< An error in the sequence of erase command occurs */
+#define SDMMC_ERROR_BAD_ERASE_PARAM 0x00000200U /*!< An invalid selection for erase groups */
+#define SDMMC_ERROR_WRITE_PROT_VIOLATION 0x00000400U /*!< Attempt to program a write protect block */
+#define SDMMC_ERROR_LOCK_UNLOCK_FAILED 0x00000800U /*!< Sequence or password error has been detected in unlock
+ command or if there was an attempt to access a locked card */
+#define SDMMC_ERROR_COM_CRC_FAILED 0x00001000U /*!< CRC check of the previous command failed */
+#define SDMMC_ERROR_ILLEGAL_CMD 0x00002000U /*!< Command is not legal for the card state */
+#define SDMMC_ERROR_CARD_ECC_FAILED 0x00004000U /*!< Card internal ECC was applied but failed to correct the data */
+#define SDMMC_ERROR_CC_ERR 0x00008000U /*!< Internal card controller error */
+#define SDMMC_ERROR_GENERAL_UNKNOWN_ERR 0x00010000U /*!< General or unknown error */
+#define SDMMC_ERROR_STREAM_READ_UNDERRUN 0x00020000U /*!< The card could not sustain data reading in stream rmode */
+#define SDMMC_ERROR_STREAM_WRITE_OVERRUN 0x00040000U /*!< The card could not sustain data programming in stream mode */
+#define SDMMC_ERROR_CID_CSD_OVERWRITE 0x00080000U /*!< CID/CSD overwrite error */
+#define SDMMC_ERROR_WP_ERASE_SKIP 0x00100000U /*!< Only partial address space was erased */
+#define SDMMC_ERROR_CARD_ECC_DISABLED 0x00200000U /*!< Command has been executed without using internal ECC */
+#define SDMMC_ERROR_ERASE_RESET 0x00400000U /*!< Erase sequence was cleared before executing because an out
+ of erase sequence command was received */
+#define SDMMC_ERROR_AKE_SEQ_ERR 0x00800000U /*!< Error in sequence of authentication */
+#define SDMMC_ERROR_INVALID_VOLTRANGE 0x01000000U /*!< Error in case of invalid voltage range */
+#define SDMMC_ERROR_ADDR_OUT_OF_RANGE 0x02000000U /*!< Error when addressed block is out of range */
+#define SDMMC_ERROR_REQUEST_NOT_APPLICABLE 0x04000000U /*!< Error when command request is not applicable */
+#define SDMMC_ERROR_INVALID_PARAMETER 0x08000000U /*!< the used parameter is not valid */
+#define SDMMC_ERROR_UNSUPPORTED_FEATURE 0x10000000U /*!< Error when feature is not insupported */
+#define SDMMC_ERROR_BUSY 0x20000000U /*!< Error when transfer process is busy */
+#define SDMMC_ERROR_DMA 0x40000000U /*!< Error while DMA transfer */
+#define SDMMC_ERROR_TIMEOUT 0x80000000U /*!< Timeout error */
+
+/**
+ * @brief SDMMC Commands Index
+ */
+#define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */
+#define SDMMC_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */
+#define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */
+#define SDMMC_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */
+#define SDMMC_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */
+#define SDMMC_CMD_SDMMC_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its
+ operating condition register (OCR) content in the response on the CMD line. */
+#define SDMMC_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */
+#define SDMMC_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */
+#define SDMMC_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information
+ and asks the card whether card supports voltage. */
+#define SDMMC_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */
+#define SDMMC_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */
+#define SDMMC_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */
+#define SDMMC_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */
+#define SDMMC_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */
+#define SDMMC_CMD_HS_BUSTEST_READ ((uint8_t)14) /*!< Reserved */
+#define SDMMC_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */
+#define SDMMC_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands
+ (read, write, lock). Default block length is fixed to 512 Bytes. Not effective
+ for SDHS and SDXC. */
+#define SDMMC_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
+ fixed 512 bytes in case of SDHC and SDXC. */
+#define SDMMC_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by
+ STOP_TRANSMISSION command. */
+#define SDMMC_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */
+#define SDMMC_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */
+#define SDMMC_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */
+#define SDMMC_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
+ fixed 512 bytes in case of SDHC and SDXC. */
+#define SDMMC_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */
+#define SDMMC_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */
+#define SDMMC_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */
+#define SDMMC_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */
+#define SDMMC_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */
+#define SDMMC_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */
+#define SDMMC_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */
+#define SDMMC_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */
+#define SDMMC_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command
+ system set by switch function command (CMD6). */
+#define SDMMC_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased.
+ Reserved for each command system set by switch function command (CMD6). */
+#define SDMMC_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */
+#define SDMMC_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */
+#define SDMMC_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */
+#define SDMMC_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by
+ the SET_BLOCK_LEN command. */
+#define SDMMC_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather
+ than a standard command. */
+#define SDMMC_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card
+ for general purpose/application specific commands. */
+#define SDMMC_CMD_NO_CMD ((uint8_t)64) /*!< No command */
+
+/**
+ * @brief Following commands are SD Card Specific commands.
+ * SDMMC_APP_CMD should be sent before sending these commands.
+ */
+#define SDMMC_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus
+ widths are given in SCR register. */
+#define SDMMC_CMD_SD_APP_STATUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */
+#define SDMMC_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with
+ 32bit+CRC data block. */
+#define SDMMC_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to
+ send its operating condition register (OCR) content in the response on the CMD line. */
+#define SDMMC_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connect/Disconnect the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card */
+#define SDMMC_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */
+#define SDMMC_CMD_SDMMC_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */
+#define SDMMC_CMD_SDMMC_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */
+
+/**
+ * @brief Following commands are SD Card Specific security commands.
+ * SDMMC_CMD_APP_CMD should be sent before sending these commands.
+ */
+#define SDMMC_CMD_SD_APP_GET_MKB ((uint8_t)43)
+#define SDMMC_CMD_SD_APP_GET_MID ((uint8_t)44)
+#define SDMMC_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45)
+#define SDMMC_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46)
+#define SDMMC_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47)
+#define SDMMC_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48)
+#define SDMMC_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18)
+#define SDMMC_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25)
+#define SDMMC_CMD_SD_APP_SECURE_ERASE ((uint8_t)38)
+#define SDMMC_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49)
+#define SDMMC_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48)
+
+/**
+ * @brief Masks for errors Card Status R1 (OCR Register)
+ */
+#define SDMMC_OCR_ADDR_OUT_OF_RANGE 0x80000000U
+#define SDMMC_OCR_ADDR_MISALIGNED 0x40000000U
+#define SDMMC_OCR_BLOCK_LEN_ERR 0x20000000U
+#define SDMMC_OCR_ERASE_SEQ_ERR 0x10000000U
+#define SDMMC_OCR_BAD_ERASE_PARAM 0x08000000U
+#define SDMMC_OCR_WRITE_PROT_VIOLATION 0x04000000U
+#define SDMMC_OCR_LOCK_UNLOCK_FAILED 0x01000000U
+#define SDMMC_OCR_COM_CRC_FAILED 0x00800000U
+#define SDMMC_OCR_ILLEGAL_CMD 0x00400000U
+#define SDMMC_OCR_CARD_ECC_FAILED 0x00200000U
+#define SDMMC_OCR_CC_ERROR 0x00100000U
+#define SDMMC_OCR_GENERAL_UNKNOWN_ERROR 0x00080000U
+#define SDMMC_OCR_STREAM_READ_UNDERRUN 0x00040000U
+#define SDMMC_OCR_STREAM_WRITE_OVERRUN 0x00020000U
+#define SDMMC_OCR_CID_CSD_OVERWRITE 0x00010000U
+#define SDMMC_OCR_WP_ERASE_SKIP 0x00008000U
+#define SDMMC_OCR_CARD_ECC_DISABLED 0x00004000U
+#define SDMMC_OCR_ERASE_RESET 0x00002000U
+#define SDMMC_OCR_AKE_SEQ_ERROR 0x00000008U
+#define SDMMC_OCR_ERRORBITS 0xFDFFE008U
+
+/**
+ * @brief Masks for R6 Response
+ */
+#define SDMMC_R6_GENERAL_UNKNOWN_ERROR 0x00002000U
+#define SDMMC_R6_ILLEGAL_CMD 0x00004000U
+#define SDMMC_R6_COM_CRC_FAILED 0x00008000U
+
+#define SDMMC_VOLTAGE_WINDOW_SD 0x80100000U
+#define SDMMC_HIGH_CAPACITY 0x40000000U
+#define SDMMC_STD_CAPACITY 0x00000000U
+#define SDMMC_CHECK_PATTERN 0x000001AAU
+
+#define SDMMC_MAX_VOLT_TRIAL 0x0000FFFFU
+
+#define SDMMC_MAX_TRIAL 0x0000FFFFU
+
+#define SDMMC_ALLZERO 0x00000000U
+
+#define SDMMC_WIDE_BUS_SUPPORT 0x00040000U
+#define SDMMC_SINGLE_BUS_SUPPORT 0x00010000U
+#define SDMMC_CARD_LOCKED 0x02000000U
+
+#define SDMMC_DATATIMEOUT 0xFFFFFFFFU
+
+#define SDMMC_0TO7BITS 0x000000FFU
+#define SDMMC_8TO15BITS 0x0000FF00U
+#define SDMMC_16TO23BITS 0x00FF0000U
+#define SDMMC_24TO31BITS 0xFF000000U
+#define SDMMC_MAX_DATA_LENGTH 0x01FFFFFFU
+
+#define SDMMC_HALFFIFO 0x00000008U
+#define SDMMC_HALFFIFOBYTES 0x00000020U
+
+/**
+ * @brief Command Class supported
+ */
+#define SDIO_CCCC_ERASE 0x00000020U
+
+#define SDIO_CMDTIMEOUT 5000U /* Command send and response timeout */
+#define SDIO_MAXERASETIMEOUT 63000U /* Max erase Timeout 63 s */
+
+
+/** @defgroup SDIO_LL_Clock_Edge Clock Edge
+ * @{
+ */
+#define SDIO_CLOCK_EDGE_RISING 0x00000000U
+#define SDIO_CLOCK_EDGE_FALLING SDIO_CLKCR_NEGEDGE
+
+#define IS_SDIO_CLOCK_EDGE(EDGE) (((EDGE) == SDIO_CLOCK_EDGE_RISING) || \
+ ((EDGE) == SDIO_CLOCK_EDGE_FALLING))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Clock_Bypass Clock Bypass
+ * @{
+ */
+#define SDIO_CLOCK_BYPASS_DISABLE 0x00000000U
+#define SDIO_CLOCK_BYPASS_ENABLE SDIO_CLKCR_BYPASS
+
+#define IS_SDIO_CLOCK_BYPASS(BYPASS) (((BYPASS) == SDIO_CLOCK_BYPASS_DISABLE) || \
+ ((BYPASS) == SDIO_CLOCK_BYPASS_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Clock_Power_Save Clock Power Saving
+ * @{
+ */
+#define SDIO_CLOCK_POWER_SAVE_DISABLE 0x00000000U
+#define SDIO_CLOCK_POWER_SAVE_ENABLE SDIO_CLKCR_PWRSAV
+
+#define IS_SDIO_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDIO_CLOCK_POWER_SAVE_DISABLE) || \
+ ((SAVE) == SDIO_CLOCK_POWER_SAVE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Bus_Wide Bus Width
+ * @{
+ */
+#define SDIO_BUS_WIDE_1B 0x00000000U
+#define SDIO_BUS_WIDE_4B SDIO_CLKCR_WIDBUS_0
+#define SDIO_BUS_WIDE_8B SDIO_CLKCR_WIDBUS_1
+
+#define IS_SDIO_BUS_WIDE(WIDE) (((WIDE) == SDIO_BUS_WIDE_1B) || \
+ ((WIDE) == SDIO_BUS_WIDE_4B) || \
+ ((WIDE) == SDIO_BUS_WIDE_8B))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Hardware_Flow_Control Hardware Flow Control
+ * @{
+ */
+#define SDIO_HARDWARE_FLOW_CONTROL_DISABLE 0x00000000U
+#define SDIO_HARDWARE_FLOW_CONTROL_ENABLE SDIO_CLKCR_HWFC_EN
+
+#define IS_SDIO_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_DISABLE) || \
+ ((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Clock_Division Clock Division
+ * @{
+ */
+#define IS_SDIO_CLKDIV(DIV) ((DIV) <= 0xFFU)
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Command_Index Command Index
+ * @{
+ */
+#define IS_SDIO_CMD_INDEX(INDEX) ((INDEX) < 0x40U)
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Response_Type Response Type
+ * @{
+ */
+#define SDIO_RESPONSE_NO 0x00000000U
+#define SDIO_RESPONSE_SHORT SDIO_CMD_WAITRESP_0
+#define SDIO_RESPONSE_LONG SDIO_CMD_WAITRESP
+
+#define IS_SDIO_RESPONSE(RESPONSE) (((RESPONSE) == SDIO_RESPONSE_NO) || \
+ ((RESPONSE) == SDIO_RESPONSE_SHORT) || \
+ ((RESPONSE) == SDIO_RESPONSE_LONG))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Wait_Interrupt_State Wait Interrupt
+ * @{
+ */
+#define SDIO_WAIT_NO 0x00000000U
+#define SDIO_WAIT_IT SDIO_CMD_WAITINT
+#define SDIO_WAIT_PEND SDIO_CMD_WAITPEND
+
+#define IS_SDIO_WAIT(WAIT) (((WAIT) == SDIO_WAIT_NO) || \
+ ((WAIT) == SDIO_WAIT_IT) || \
+ ((WAIT) == SDIO_WAIT_PEND))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_CPSM_State CPSM State
+ * @{
+ */
+#define SDIO_CPSM_DISABLE 0x00000000U
+#define SDIO_CPSM_ENABLE SDIO_CMD_CPSMEN
+
+#define IS_SDIO_CPSM(CPSM) (((CPSM) == SDIO_CPSM_DISABLE) || \
+ ((CPSM) == SDIO_CPSM_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Response_Registers Response Register
+ * @{
+ */
+#define SDIO_RESP1 0x00000000U
+#define SDIO_RESP2 0x00000004U
+#define SDIO_RESP3 0x00000008U
+#define SDIO_RESP4 0x0000000CU
+
+#define IS_SDIO_RESP(RESP) (((RESP) == SDIO_RESP1) || \
+ ((RESP) == SDIO_RESP2) || \
+ ((RESP) == SDIO_RESP3) || \
+ ((RESP) == SDIO_RESP4))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Data_Length Data Lenght
+ * @{
+ */
+#define IS_SDIO_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFFU)
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Data_Block_Size Data Block Size
+ * @{
+ */
+#define SDIO_DATABLOCK_SIZE_1B 0x00000000U
+#define SDIO_DATABLOCK_SIZE_2B SDIO_DCTRL_DBLOCKSIZE_0
+#define SDIO_DATABLOCK_SIZE_4B SDIO_DCTRL_DBLOCKSIZE_1
+#define SDIO_DATABLOCK_SIZE_8B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1)
+#define SDIO_DATABLOCK_SIZE_16B SDIO_DCTRL_DBLOCKSIZE_2
+#define SDIO_DATABLOCK_SIZE_32B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2)
+#define SDIO_DATABLOCK_SIZE_64B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2)
+#define SDIO_DATABLOCK_SIZE_128B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2)
+#define SDIO_DATABLOCK_SIZE_256B SDIO_DCTRL_DBLOCKSIZE_3
+#define SDIO_DATABLOCK_SIZE_512B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_3)
+#define SDIO_DATABLOCK_SIZE_1024B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3)
+#define SDIO_DATABLOCK_SIZE_2048B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3)
+#define SDIO_DATABLOCK_SIZE_4096B (SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3)
+#define SDIO_DATABLOCK_SIZE_8192B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3)
+#define SDIO_DATABLOCK_SIZE_16384B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3)
+
+#define IS_SDIO_BLOCK_SIZE(SIZE) (((SIZE) == SDIO_DATABLOCK_SIZE_1B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_2B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_4B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_8B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_16B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_32B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_64B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_128B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_256B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_512B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_1024B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_2048B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_4096B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_8192B) || \
+ ((SIZE) == SDIO_DATABLOCK_SIZE_16384B))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Transfer_Direction Transfer Direction
+ * @{
+ */
+#define SDIO_TRANSFER_DIR_TO_CARD 0x00000000U
+#define SDIO_TRANSFER_DIR_TO_SDIO SDIO_DCTRL_DTDIR
+
+#define IS_SDIO_TRANSFER_DIR(DIR) (((DIR) == SDIO_TRANSFER_DIR_TO_CARD) || \
+ ((DIR) == SDIO_TRANSFER_DIR_TO_SDIO))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Transfer_Type Transfer Type
+ * @{
+ */
+#define SDIO_TRANSFER_MODE_BLOCK 0x00000000U
+#define SDIO_TRANSFER_MODE_STREAM SDIO_DCTRL_DTMODE
+
+#define IS_SDIO_TRANSFER_MODE(MODE) (((MODE) == SDIO_TRANSFER_MODE_BLOCK) || \
+ ((MODE) == SDIO_TRANSFER_MODE_STREAM))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_DPSM_State DPSM State
+ * @{
+ */
+#define SDIO_DPSM_DISABLE 0x00000000U
+#define SDIO_DPSM_ENABLE SDIO_DCTRL_DTEN
+
+#define IS_SDIO_DPSM(DPSM) (((DPSM) == SDIO_DPSM_DISABLE) ||\
+ ((DPSM) == SDIO_DPSM_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Read_Wait_Mode Read Wait Mode
+ * @{
+ */
+#define SDIO_READ_WAIT_MODE_DATA2 0x00000000U
+#define SDIO_READ_WAIT_MODE_CLK (SDIO_DCTRL_RWMOD)
+
+#define IS_SDIO_READWAIT_MODE(MODE) (((MODE) == SDIO_READ_WAIT_MODE_CLK) || \
+ ((MODE) == SDIO_READ_WAIT_MODE_DATA2))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Interrupt_sources Interrupt Sources
+ * @{
+ */
+#define SDIO_IT_CCRCFAIL SDIO_STA_CCRCFAIL
+#define SDIO_IT_DCRCFAIL SDIO_STA_DCRCFAIL
+#define SDIO_IT_CTIMEOUT SDIO_STA_CTIMEOUT
+#define SDIO_IT_DTIMEOUT SDIO_STA_DTIMEOUT
+#define SDIO_IT_TXUNDERR SDIO_STA_TXUNDERR
+#define SDIO_IT_RXOVERR SDIO_STA_RXOVERR
+#define SDIO_IT_CMDREND SDIO_STA_CMDREND
+#define SDIO_IT_CMDSENT SDIO_STA_CMDSENT
+#define SDIO_IT_DATAEND SDIO_STA_DATAEND
+#define SDIO_IT_STBITERR SDIO_STA_STBITERR
+#define SDIO_IT_DBCKEND SDIO_STA_DBCKEND
+#define SDIO_IT_CMDACT SDIO_STA_CMDACT
+#define SDIO_IT_TXACT SDIO_STA_TXACT
+#define SDIO_IT_RXACT SDIO_STA_RXACT
+#define SDIO_IT_TXFIFOHE SDIO_STA_TXFIFOHE
+#define SDIO_IT_RXFIFOHF SDIO_STA_RXFIFOHF
+#define SDIO_IT_TXFIFOF SDIO_STA_TXFIFOF
+#define SDIO_IT_RXFIFOF SDIO_STA_RXFIFOF
+#define SDIO_IT_TXFIFOE SDIO_STA_TXFIFOE
+#define SDIO_IT_RXFIFOE SDIO_STA_RXFIFOE
+#define SDIO_IT_TXDAVL SDIO_STA_TXDAVL
+#define SDIO_IT_RXDAVL SDIO_STA_RXDAVL
+#define SDIO_IT_SDIOIT SDIO_STA_SDIOIT
+#define SDIO_IT_CEATAEND SDIO_STA_CEATAEND
+/**
+ * @}
+ */
+
+/** @defgroup SDMMC_LL_Flags Flags
+ * @{
+ */
+#define SDIO_FLAG_CCRCFAIL SDIO_STA_CCRCFAIL
+#define SDIO_FLAG_DCRCFAIL SDIO_STA_DCRCFAIL
+#define SDIO_FLAG_CTIMEOUT SDIO_STA_CTIMEOUT
+#define SDIO_FLAG_DTIMEOUT SDIO_STA_DTIMEOUT
+#define SDIO_FLAG_TXUNDERR SDIO_STA_TXUNDERR
+#define SDIO_FLAG_RXOVERR SDIO_STA_RXOVERR
+#define SDIO_FLAG_CMDREND SDIO_STA_CMDREND
+#define SDIO_FLAG_CMDSENT SDIO_STA_CMDSENT
+#define SDIO_FLAG_DATAEND SDIO_STA_DATAEND
+#define SDIO_FLAG_STBITERR SDIO_STA_STBITERR
+#define SDIO_FLAG_DBCKEND SDIO_STA_DBCKEND
+#define SDIO_FLAG_CMDACT SDIO_STA_CMDACT
+#define SDIO_FLAG_TXACT SDIO_STA_TXACT
+#define SDIO_FLAG_RXACT SDIO_STA_RXACT
+#define SDIO_FLAG_TXFIFOHE SDIO_STA_TXFIFOHE
+#define SDIO_FLAG_RXFIFOHF SDIO_STA_RXFIFOHF
+#define SDIO_FLAG_TXFIFOF SDIO_STA_TXFIFOF
+#define SDIO_FLAG_RXFIFOF SDIO_STA_RXFIFOF
+#define SDIO_FLAG_TXFIFOE SDIO_STA_TXFIFOE
+#define SDIO_FLAG_RXFIFOE SDIO_STA_RXFIFOE
+#define SDIO_FLAG_TXDAVL SDIO_STA_TXDAVL
+#define SDIO_FLAG_RXDAVL SDIO_STA_RXDAVL
+#define SDIO_FLAG_SDIOIT SDIO_STA_SDIOIT
+#define SDIO_FLAG_CEATAEND SDIO_STA_CEATAEND
+#define SDIO_STATIC_FLAGS ((uint32_t)(SDIO_FLAG_CCRCFAIL | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_CTIMEOUT |\
+ SDIO_FLAG_DTIMEOUT | SDIO_FLAG_TXUNDERR | SDIO_FLAG_RXOVERR |\
+ SDIO_FLAG_CMDREND | SDIO_FLAG_CMDSENT | SDIO_FLAG_DATAEND |\
+ SDIO_FLAG_DBCKEND))
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup SDIO_LL_Exported_macros SDIO_LL Exported Macros
+ * @{
+ */
+
+/** @defgroup SDMMC_LL_Alias_Region Bit Address in the alias region
+ * @{
+ */
+/* ------------ SDIO registers bit address in the alias region -------------- */
+#define SDIO_OFFSET (SDIO_BASE - PERIPH_BASE)
+
+/* --- CLKCR Register ---*/
+/* Alias word address of CLKEN bit */
+#define CLKCR_OFFSET (SDIO_OFFSET + 0x04U)
+#define CLKEN_BITNUMBER 0x08U
+#define CLKCR_CLKEN_BB (PERIPH_BB_BASE + (CLKCR_OFFSET * 32U) + (CLKEN_BITNUMBER * 4U))
+
+/* --- CMD Register ---*/
+/* Alias word address of SDIOSUSPEND bit */
+#define CMD_OFFSET (SDIO_OFFSET + 0x0CU)
+#define SDIOSUSPEND_BITNUMBER 0x0BU
+#define CMD_SDIOSUSPEND_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (SDIOSUSPEND_BITNUMBER * 4U))
+
+/* Alias word address of ENCMDCOMPL bit */
+#define ENCMDCOMPL_BITNUMBER 0x0CU
+#define CMD_ENCMDCOMPL_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ENCMDCOMPL_BITNUMBER * 4U))
+
+/* Alias word address of NIEN bit */
+#define NIEN_BITNUMBER 0x0DU
+#define CMD_NIEN_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (NIEN_BITNUMBER * 4U))
+
+/* Alias word address of ATACMD bit */
+#define ATACMD_BITNUMBER 0x0EU
+#define CMD_ATACMD_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ATACMD_BITNUMBER * 4U))
+
+/* --- DCTRL Register ---*/
+/* Alias word address of DMAEN bit */
+#define DCTRL_OFFSET (SDIO_OFFSET + 0x2CU)
+#define DMAEN_BITNUMBER 0x03U
+#define DCTRL_DMAEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (DMAEN_BITNUMBER * 4U))
+
+/* Alias word address of RWSTART bit */
+#define RWSTART_BITNUMBER 0x08U
+#define DCTRL_RWSTART_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTART_BITNUMBER * 4U))
+
+/* Alias word address of RWSTOP bit */
+#define RWSTOP_BITNUMBER 0x09U
+#define DCTRL_RWSTOP_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTOP_BITNUMBER * 4U))
+
+/* Alias word address of RWMOD bit */
+#define RWMOD_BITNUMBER 0x0AU
+#define DCTRL_RWMOD_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWMOD_BITNUMBER * 4U))
+
+/* Alias word address of SDIOEN bit */
+#define SDIOEN_BITNUMBER 0x0BU
+#define DCTRL_SDIOEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (SDIOEN_BITNUMBER * 4U))
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Register Bits And Addresses Definitions
+ * @brief SDIO_LL registers bit address in the alias region
+ * @{
+ */
+/* ---------------------- SDIO registers bit mask --------------------------- */
+/* --- CLKCR Register ---*/
+/* CLKCR register clear mask */
+#define CLKCR_CLEAR_MASK ((uint32_t)(SDIO_CLKCR_CLKDIV | SDIO_CLKCR_PWRSAV |\
+ SDIO_CLKCR_BYPASS | SDIO_CLKCR_WIDBUS |\
+ SDIO_CLKCR_NEGEDGE | SDIO_CLKCR_HWFC_EN))
+
+/* --- DCTRL Register ---*/
+/* SDIO DCTRL Clear Mask */
+#define DCTRL_CLEAR_MASK ((uint32_t)(SDIO_DCTRL_DTEN | SDIO_DCTRL_DTDIR |\
+ SDIO_DCTRL_DTMODE | SDIO_DCTRL_DBLOCKSIZE))
+
+/* --- CMD Register ---*/
+/* CMD Register clear mask */
+#define CMD_CLEAR_MASK ((uint32_t)(SDIO_CMD_CMDINDEX | SDIO_CMD_WAITRESP |\
+ SDIO_CMD_WAITINT | SDIO_CMD_WAITPEND |\
+ SDIO_CMD_CPSMEN | SDIO_CMD_SDIOSUSPEND))
+
+/* SDIO RESP Registers Address */
+#define SDIO_RESP_ADDR ((uint32_t)(SDIO_BASE + 0x14))
+
+/* SDIO Intialization Frequency (400KHz max) */
+#define SDIO_INIT_CLK_DIV ((uint8_t)0xC3)
+
+/* SDIO Data Transfer Frequency */
+#define SDIO_TRANSFER_CLK_DIV ((uint8_t)0x9)
+
+/**
+ * @}
+ */
+
+/** @defgroup SDIO_LL_Interrupt_Clock Interrupt And Clock Configuration
+ * @brief macros to handle interrupts and specific clock configurations
+ * @{
+ */
+
+/**
+ * @brief Enable the SDIO device.
+ * @param __INSTANCE__: SDIO Instance
+ * @retval None
+ */
+#define __SDIO_ENABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = ENABLE)
+
+/**
+ * @brief Disable the SDIO device.
+ * @param __INSTANCE__: SDIO Instance
+ * @retval None
+ */
+#define __SDIO_DISABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = DISABLE)
+
+/**
+ * @brief Enable the SDIO DMA transfer.
+ * @param __INSTANCE__: SDIO Instance
+ * @retval None
+ */
+#define __SDIO_DMA_ENABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = ENABLE)
+/**
+ * @brief Disable the SDIO DMA transfer.
+ * @param __INSTANCE__: SDIO Instance
+ * @retval None
+ */
+#define __SDIO_DMA_DISABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = DISABLE)
+
+/**
+ * @brief Enable the SDIO device interrupt.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be enabled.
+ * This parameter can be one or a combination of the following values:
+ * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+ * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+ * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+ * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+ * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+ * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
+ * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
+ * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
+ * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
+ * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
+ * @arg SDIO_IT_RXACT: Data receive in progress interrupt
+ * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+ * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+ * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
+ * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
+ * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
+ * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
+ * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
+ * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
+ * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
+ * @retval None
+ */
+#define __SDIO_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK |= (__INTERRUPT__))
+
+/**
+ * @brief Disable the SDIO device interrupt.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be disabled.
+ * This parameter can be one or a combination of the following values:
+ * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+ * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+ * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+ * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+ * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+ * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
+ * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
+ * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
+ * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
+ * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
+ * @arg SDIO_IT_RXACT: Data receive in progress interrupt
+ * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+ * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+ * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
+ * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
+ * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
+ * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
+ * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
+ * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
+ * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
+ * @retval None
+ */
+#define __SDIO_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK &= ~(__INTERRUPT__))
+
+/**
+ * @brief Checks whether the specified SDIO flag is set or not.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+ * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+ * @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+ * @arg SDIO_FLAG_DTIMEOUT: Data timeout
+ * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+ * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error
+ * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed)
+ * @arg SDIO_FLAG_CMDSENT: Command sent (no response required)
+ * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero)
+ * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed)
+ * @arg SDIO_FLAG_CMDACT: Command transfer in progress
+ * @arg SDIO_FLAG_TXACT: Data transmit in progress
+ * @arg SDIO_FLAG_RXACT: Data receive in progress
+ * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty
+ * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full
+ * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full
+ * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full
+ * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty
+ * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty
+ * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO
+ * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO
+ * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received
+ * @retval The new state of SDIO_FLAG (SET or RESET).
+ */
+#define __SDIO_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->STA &(__FLAG__)) != RESET)
+
+
+/**
+ * @brief Clears the SDIO pending flags.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __FLAG__: specifies the flag to clear.
+ * This parameter can be one or a combination of the following values:
+ * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+ * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+ * @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+ * @arg SDIO_FLAG_DTIMEOUT: Data timeout
+ * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+ * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error
+ * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed)
+ * @arg SDIO_FLAG_CMDSENT: Command sent (no response required)
+ * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero)
+ * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed)
+ * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received
+ * @retval None
+ */
+#define __SDIO_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->ICR = (__FLAG__))
+
+/**
+ * @brief Checks whether the specified SDIO interrupt has occurred or not.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __INTERRUPT__: specifies the SDIO interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+ * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+ * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+ * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+ * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+ * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
+ * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
+ * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
+ * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
+ * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
+ * @arg SDIO_IT_RXACT: Data receive in progress interrupt
+ * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+ * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+ * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
+ * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
+ * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
+ * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
+ * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
+ * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
+ * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
+ * @retval The new state of SDIO_IT (SET or RESET).
+ */
+#define __SDIO_GET_IT (__INSTANCE__, __INTERRUPT__) (((__INSTANCE__)->STA &(__INTERRUPT__)) == (__INTERRUPT__))
+
+/**
+ * @brief Clears the SDIO's interrupt pending bits.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
+ * This parameter can be one or a combination of the following values:
+ * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+ * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+ * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+ * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+ * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+ * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
+ * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
+ * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
+ * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt
+ * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
+ * @retval None
+ */
+#define __SDIO_CLEAR_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->ICR = (__INTERRUPT__))
+
+/**
+ * @brief Enable Start the SD I/O Read Wait operation.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_START_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = ENABLE)
+
+/**
+ * @brief Disable Start the SD I/O Read Wait operations.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_START_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = DISABLE)
+
+/**
+ * @brief Enable Start the SD I/O Read Wait operation.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_STOP_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = ENABLE)
+
+/**
+ * @brief Disable Stop the SD I/O Read Wait operations.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_STOP_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = DISABLE)
+
+/**
+ * @brief Enable the SD I/O Mode Operation.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_OPERATION_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = ENABLE)
+
+/**
+ * @brief Disable the SD I/O Mode Operation.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_OPERATION_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = DISABLE)
+
+/**
+ * @brief Enable the SD I/O Suspend command sending.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_SUSPEND_CMD_ENABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = ENABLE)
+
+/**
+ * @brief Disable the SD I/O Suspend command sending.
+ * @param __INSTANCE__ : Pointer to SDIO register base
+ * @retval None
+ */
+#define __SDIO_SUSPEND_CMD_DISABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = DISABLE)
+/**
+ * @brief Enable the command completion signal.
+ * @retval None
+ */
+#define __SDIO_CEATA_CMD_COMPLETION_ENABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = ENABLE)
+
+/**
+ * @brief Disable the command completion signal.
+ * @retval None
+ */
+#define __SDIO_CEATA_CMD_COMPLETION_DISABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = DISABLE)
+
+/**
+ * @brief Enable the CE-ATA interrupt.
+ * @retval None
+ */
+#define __SDIO_CEATA_ENABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)0U)
+
+/**
+ * @brief Disable the CE-ATA interrupt.
+ * @retval None
+ */
+#define __SDIO_CEATA_DISABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)1U)
+
+/**
+ * @brief Enable send CE-ATA command (CMD61).
+ * @retval None
+ */
+#define __SDIO_CEATA_SENDCMD_ENABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = ENABLE)
+
+/**
+ * @brief Disable send CE-ATA command (CMD61).
+ * @retval None
+ */
+#define __SDIO_CEATA_SENDCMD_DISABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = DISABLE)
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SDMMC_LL_Exported_Functions
+ * @{
+ */
+
+/* Initialization/de-initialization functions **********************************/
+/** @addtogroup HAL_SDMMC_LL_Group1
+ * @{
+ */
+HAL_StatusTypeDef SDIO_Init(SDIO_TypeDef *SDIOx, SDIO_InitTypeDef Init);
+/**
+ * @}
+ */
+
+/* I/O operation functions *****************************************************/
+/** @addtogroup HAL_SDMMC_LL_Group2
+ * @{
+ */
+/* Blocking mode: Polling */
+uint32_t SDIO_ReadFIFO(SDIO_TypeDef *SDIOx);
+HAL_StatusTypeDef SDIO_WriteFIFO(SDIO_TypeDef *SDIOx, uint32_t *pWriteData);
+/**
+ * @}
+ */
+
+/* Peripheral Control functions ************************************************/
+/** @addtogroup HAL_SDMMC_LL_Group3
+ * @{
+ */
+HAL_StatusTypeDef SDIO_PowerState_ON(SDIO_TypeDef *SDIOx);
+HAL_StatusTypeDef SDIO_PowerState_OFF(SDIO_TypeDef *SDIOx);
+uint32_t SDIO_GetPowerState(SDIO_TypeDef *SDIOx);
+
+/* Command path state machine (CPSM) management functions */
+HAL_StatusTypeDef SDIO_SendCommand(SDIO_TypeDef *SDIOx, SDIO_CmdInitTypeDef *Command);
+uint8_t SDIO_GetCommandResponse(SDIO_TypeDef *SDIOx);
+uint32_t SDIO_GetResponse(SDIO_TypeDef *SDIOx, uint32_t Response);
+
+/* Data path state machine (DPSM) management functions */
+HAL_StatusTypeDef SDIO_ConfigData(SDIO_TypeDef *SDIOx, SDIO_DataInitTypeDef* Data);
+uint32_t SDIO_GetDataCounter(SDIO_TypeDef *SDIOx);
+uint32_t SDIO_GetFIFOCount(SDIO_TypeDef *SDIOx);
+
+/* SDMMC Cards mode management functions */
+HAL_StatusTypeDef SDIO_SetSDMMCReadWaitMode(SDIO_TypeDef *SDIOx, uint32_t SDIO_ReadWaitMode);
+
+/* SDMMC Commands management functions */
+uint32_t SDMMC_CmdBlockLength(SDIO_TypeDef *SDIOx, uint32_t BlockSize);
+uint32_t SDMMC_CmdReadSingleBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd);
+uint32_t SDMMC_CmdReadMultiBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd);
+uint32_t SDMMC_CmdWriteSingleBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd);
+uint32_t SDMMC_CmdWriteMultiBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd);
+uint32_t SDMMC_CmdSDEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd);
+uint32_t SDMMC_CmdSDEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd);
+uint32_t SDMMC_CmdErase(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdStopTransfer(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdSelDesel(SDIO_TypeDef *SDIOx, uint64_t Addr);
+uint32_t SDMMC_CmdGoIdleState(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdOperCond(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdAppCommand(SDIO_TypeDef *SDIOx, uint32_t Argument);
+uint32_t SDMMC_CmdAppOperCommand(SDIO_TypeDef *SDIOx, uint32_t SdType);
+uint32_t SDMMC_CmdBusWidth(SDIO_TypeDef *SDIOx, uint32_t BusWidth);
+uint32_t SDMMC_CmdSendSCR(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdSendCID(SDIO_TypeDef *SDIOx);
+uint32_t SDMMC_CmdSendCSD(SDIO_TypeDef *SDIOx, uint32_t Argument);
+uint32_t SDMMC_CmdSetRelAdd(SDIO_TypeDef *SDIOx, uint16_t *pRCA);
+uint32_t SDMMC_CmdSendStatus(SDIO_TypeDef *SDIOx, uint32_t Argument);
+uint32_t SDMMC_CmdStatusRegister(SDIO_TypeDef *SDIOx);
+
+uint32_t SDMMC_CmdOpCondition(SDIO_TypeDef *SDIOx, uint32_t Argument);
+uint32_t SDMMC_CmdSwitch(SDIO_TypeDef *SDIOx, uint32_t Argument);
+uint32_t SDMMC_CmdEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd);
+uint32_t SDMMC_CmdEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F103xE || STM32F103xG */
+
+#endif /* __stm32f1xx_LL_SD_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|