1 files changed, 169 insertions, 0 deletions
diff --git a/config/printer-creality-cr10-v3-2020.cfg b/config/printer-creality-cr10-v3-2020.cfg
new file mode 100644
index 00000000..fec583fa
--- /dev/null
+++ b/config/printer-creality-cr10-v3-2020.cfg
@@ -0,0 +1,169 @@
+# This file contains common pin mappings for the 2020 Creality
+# CR-10 V3. The mainboard is a Creality 3D v2.5.2 (8-bit mainboard
+# with ATMega2560).
+# To use this config, the firmware should be compiled for the
+# AVR atmega2560.
+#
+# To flash do "make flash" and if it does not and avrdude also
+# does not work then one may need to flash a bootloader to the
+# board - see the Klipper docs/Bootloaders.md file for more
+# information.
+#
+# See docs/Config_Reference.md for a description of parameters.
+#
+# For better compatibility with GCodes generated for Marlin, you
+# may wish to add the following section, if you have BLTouch:
+#[gcode_macro G29]
+#gcode:
+#    BED_MESH_CALIBRATE
+#
+#
+[stepper_x]
+step_pin: PF0 #ar54
+dir_pin: PF1 #ar55
+enable_pin: !PD7 #!ar38
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PE5 #^ar3
+position_endstop: 0
+position_max: 300
+homing_speed: 50
+
+[stepper_y]
+step_pin: PF6 #ar60
+dir_pin: PF7 #ar61
+enable_pin: !PF2 #!ar56
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PJ1 #^ar14
+position_endstop: 0
+position_max: 300
+homing_speed: 50
+
+[stepper_z]
+step_pin: PL3 #ar46
+dir_pin: !PL1 #!ar48
+enable_pin: !PK0 #!ar62
+microsteps: 16
+rotation_distance: 8
+position_max: 400
+#Uncomment if you have a BL-Touch:
+#position_min: -4
+#endstop_pin: probe:z_virtual_endstop
+#and comment the follwing lines:
+position_endstop: 0.0
+endstop_pin: ^PD3 #ar18
+
+[safe_z_home]
+home_xy_position: 104.25,147.6
+speed: 80
+z_hop: 10
+z_hop_speed: 10
+
+[extruder]
+step_pin: PA4 # ar26
+dir_pin: !PA6 # !ar28
+enable_pin: !PA2 # !ar24
+microsteps: 16
+rotation_distance: 7.7201944 # 16 microsteps * 200 steps/rotation / steps/mm
+#Correction formula is new_rotation_distance = old_rotation_distance * mmsExtracted / 100.0
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4 #ar10
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5 #analog13
+control: pid
+pid_kp: 22.107
+pid_ki: 1.170
+pid_kd: 104.458
+min_temp: 0
+max_temp: 255
+
+[heater_bed]
+heater_pin: PH5 #ar8
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PK6 #analog14
+control: pid
+#Stock PID configuration taken from Marlin
+pid_Kp: 201.86
+pid_Ki: 10.67
+pid_Kd: 954.96
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PH6 #ar9
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PH1 #ar16
+sclk_pin: PA1 #ar23
+sid_pin: PH0 #ar17
+encoder_pins: ^PC4, ^PC6 #^ar33, ^ar31
+click_pin: ^!PC2 #^!ar35
+
+
+#Uncomment the following lines if you have a BL-Touch
+#[bltouch]
+#sensor_pin: ^PD2 #^ar19
+#control_pin: PB5 #ar11
+#set_output_mode: 5V
+#pin_move_time: 0.4
+#stow_on_each_sample: False
+#probe_with_touch_mode: False
+#x_offset: 45.75
+#y_offset: -3.40
+#z_offset:  3.28
+#samples: 2
+#sample_retract_dist: 2
+#samples_result: average
+
+#Uncomment the following lines if you have a BL-Touch
+#[bed_mesh]
+#speed: 50
+#horizontal_move_z: 6
+#mesh_min: 46.50,0.75
+#mesh_max: 253.5,295.85
+#probe_count: 7,7
+#algorithm: bicubic
+
+[pause_resume]
+recover_velocity: 50
+
+[filament_switch_sensor fil_runout_sensor]
+pause_on_runout: True
+switch_pin: PE4 #ar2
+
+[bed_screws]
+screw1: 33,29
+screw1_name: front left screw
+screw2: 273,29
+screw2_name: front right screw
+screw3: 273,269
+screw3_name: rear right screw
+screw4: 33,269
+screw4_name: rear right screw
+
+#Uncomment the following lines if you have a BL-Touch
+#[screws_tilt_adjust]
+#screw1: 0,29
+#screw1_name: front left screw
+#screw2: 228,29
+#screw2_name: front right screw
+#screw3: 228,269
+#screw3_name: rear right screw
+#screw4: 0,269
+#screw4_name: rear right screw
+#speed: 50
+#horizontal_move_z: 10
+#screw_thread: CW-M3