1 files changed, 84 insertions, 0 deletions
diff --git a/config/sample-bigtreetech-ebb-sb-canbus-v1.0.cfg b/config/sample-bigtreetech-ebb-sb-canbus-v1.0.cfg
new file mode 100644
index 00000000..192d385e
--- /dev/null
+++ b/config/sample-bigtreetech-ebb-sb-canbus-v1.0.cfg
@@ -0,0 +1,84 @@
+# This file contains common pin mappings for the BIGTREETECH EBBCan
+# Canbus board. To use this config, the firmware should be compiled for the
+# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
+# The "EBB Can" micro-controller will be used to control the components on the nozzle.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[mcu EBBCan]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+#canbus_uuid: 0e0d81e4210c
+
+[temperature_sensor EBB_NTC]
+sensor_type: Generic 3950
+sensor_pin: EBBCan:PA2
+
+[adxl345]
+cs_pin: EBBCan:PB12
+spi_software_sclk_pin: EBBCan:PB10
+spi_software_mosi_pin: EBBCan:PB11
+spi_software_miso_pin: EBBCan:PB2
+axes_map: x,y,z
+
+[extruder]
+step_pin: EBBCan:PD0
+dir_pin: !EBBCan:PD1
+enable_pin: !EBBCan:PD2
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: EBBCan:PB13
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: EBBCan:PA3
+control: pid
+pid_Kp: 21.527
+pid_Ki: 1.063
+pid_Kd: 108.982
+min_temp: 0
+max_temp: 250
+
+# sensor_type:MAX31865
+# sensor_pin: EBBCan:PA4
+# spi_bus: spi1
+# rtd_nominal_r: 100
+# rtd_reference_r: 430
+# rtd_num_of_wires: 2
+
+[tmc2209 extruder]
+uart_pin: EBBCan:PA15
+run_current: 0.650
+stealthchop_threshold: 999999
+
+[fan]
+pin: EBBCan:PA0
+
+[heater_fan hotend_fan]
+pin: EBBCan:PA1
+heater: extruder
+heater_temp: 50.0
+
+#[heater_fan 4W_FAN0]
+#pin: EBBCan:PB14
+#tachometer_pin: EBBCan:PB15
+#tachometer_ppr: 1
+
+#[neopixel hotend_rgb]
+#pin: EBBCan:PD3
+
+#[bltouch]
+#sensor_pin: ^EBBCan:PB8
+#control_pin: EBBCan:PB9
+
+## NPN and PNP proximity switch types can be set by jumper
+#[probe]
+#pin: ^EBBCan:PC13
+
+#[output_pin PB5]
+#pin: EBBCan:PB5
+
+#[output_pin PB7]
+#pin: EBBCan:PB7
+
+#[output_pin PB6]
+#pin: EBBCan:PB6