1 files changed, 161 insertions, 0 deletions
diff --git a/config/generic-mellow-fly-gemini-v2.cfg b/config/generic-mellow-fly-gemini-v2.cfg
new file mode 100644
index 00000000..ed919d1b
--- /dev/null
+++ b/config/generic-mellow-fly-gemini-v2.cfg
@@ -0,0 +1,161 @@
+# This file contains common pin mappings for the Mellow Fly-Gemini-v2.
+# To use this config, the firmware should be compiled for the
+# STM32F405 with a "32KiB bootloader".
+
+# The "make flash" command does not work on the Fly-Gemini-v2. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "firmware.bin" or "klipper.bin" on an SD card and then restart the Fly-Gemini-v2
+# with that SD card.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC13
+dir_pin: PC1
+enable_pin: !PB2
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PA3
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC14
+dir_pin: !PC4
+enable_pin: !PD2
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PB1
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: PC15
+dir_pin: PC5
+enable_pin: !PC12
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PB10
+position_endstop: 0.5
+position_max: 200
+
+[extruder]
+step_pin: PC3
+dir_pin: PC8
+enable_pin: !PC11
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: Generic 3950
+sensor_pin: PC2
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PC6
+
+#FAN1
+#[heater_fan fan1]
+#pin: PC7
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+
+########################################
+# TMC2209 configuration
+########################################
+
+#[tmc2209 stepper_x]
+#uart_pin: PB11
+#run_current: 0.800
+#diag_pin: PA3
+#stealthchop_threshold: 999999
+
+#[tmc2209 stepper_y]
+#uart_pin: PB9
+#run_current: 0.800
+#diag_pin: PB1
+#stealthchop_threshold: 999999
+
+#[tmc2209 stepper_z]
+#uart_pin: PB8
+#run_current: 0.800
+#diag_pin: PB10
+#stealthchop_threshold: 999999
+
+#[tmc2209 extruder]
+#uart_pin: PB7
+#run_current: 0.600
+#diag_pin:
+#stealthchop_threshold: 999999
+
+########################################
+# TMC5160 configuration
+########################################
+
+#[tmc5160 stepper_x]
+#cs_pin: PB11
+#spi_bus: spi1
+#run_current: 0.800
+#diag1_pin: PA3
+#stealthchop_threshold: 999999
+
+#[tmc5160 stepper_y]
+#cs_pin: PB9
+#spi_bus: spi1
+#run_current: 0.800
+#diag1_pin: PB1
+#stealthchop_threshold: 999999
+
+#[tmc5160 stepper_z]
+#cs_pin: PB8
+#spi_bus: spi1
+#run_current: 0.800
+#diag1_pin: PB10
+#stealthchop_threshold: 999999
+
+#[tmc5160 extruder]
+#cs_pin: PB7
+#spi_bus: spi1
+#run_current: 0.800
+#diag1_pin:
+#stealthchop_threshold: 999999
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PC9,  EXP1_3=PA13,  EXP1_5=PA9,   EXP1_7=<NC>,  EXP1_9=<GND>,
+    EXP1_2=PB6,  EXP1_4=PA10,  EXP1_6=PA8,   EXP1_8=<NC>,  EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB14, EXP2_3=PA15,  EXP2_5=PA14,  EXP2_7=PC10,   EXP2_9=<GND>,
+    EXP2_2=PB13, EXP2_4=PB12,  EXP2_6=PB15,  EXP2_8=<RST>, EXP2_10=<NC>,
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.