1 files changed, 152 insertions, 0 deletions
diff --git a/config/generic-duet3-6hc.cfg b/config/generic-duet3-6hc.cfg
new file mode 100644
index 00000000..e8f55205
--- /dev/null
+++ b/config/generic-duet3-6hc.cfg
@@ -0,0 +1,152 @@
+# This file contains common pin mappings for the Duet3 6HC. To use
+# this config, the firmware should be compiled for the SAME70Q20B.
+
+# To flash the board, erase the existing firmware by jumpering the erase jumper.
+# Boot the board, wait for reset to complete, remove the jumper, and then reboot the board,
+# as described in Duet's documentation:
+#    https://docs.duet3d.com/en/User_manual/RepRapFirmware/Updating_firmware#all-other-duet-boards
+# Then run: make flash FLASH_DEVICE=/dev/ttyACM0
+
+# See docs/Config_Reference.md for a description of parameters.
+
+
+# Pins for reference, v1.02 board:
+# Driver Step Pins - 0:PC18 1:PC16 2:PC28 3:PC1  4:PC4 5:PC9
+# Driver Dir Pins  - 0:PB5  1:PD10 2:PA4  3:PA22 4:PC3 5:PD14
+# Driver Enable - !PA9
+# Driver CS - PD17
+# Thermistor Pins - TEMP0:PC15 TEMP1:PC29 TEMP2:PC30 TEMP3:PC31
+# Pullup Resistor - 2200
+# Vssa Sense:PC13 | Vref Sense:PC0
+# Current Sense resistor for drivers - 0.05ohm
+# SPI lines:{PC25} -> SPIMosi:PC27 SPIMiso:PC26 SPISCLK:PC24
+# Vin Monitor:PA20
+# CAN Pins - TX0:PB2 RX0:PB3 TX1:PD12 RX1:PC12
+# Heaters - Out0:PA7 Out1:PA24 Out2:PA16 Out3:PA11
+# Fan outputs - Out4:PA15 Out5:PC5 Out6:PA8 Out7:PC11 Out8:PC8 Out9:PA12 | Out9 is shared with VFD_Out
+# Tach Pins for Fans - Out4.Tach:PC7 Out5.Tach:PD23 Out6.Tach:PA1
+# GPIO_out - IO0:PD26 IO1:PD16 IO2:PD27 IO3:PA3 IO4:PE0  IO5:PD21 IO6:PA0  IO7:PD23 IO8:PE1
+# GPIO_in -  IO0:PD25 IO1:PD15 IO2:PD28 IO3:PE5 IO4:PD30 IO5:PA19 IO6:PA18 IO7:PA17 IO8:PE3
+# Driver Diag - 0:PD29 1:PC17 2:PD13 3:PC2 4:PD31 5:PC10
+
+[stepper_x]
+#driver 0
+step_pin: PC18
+dir_pin: PB5
+enable_pin: !PA9
+microsteps: 128
+rotation_distance: 40
+endstop_pin: PD25 #IO0
+position_endstop: 0
+position_max: 450
+
+[tmc5160 stepper_x]
+cs_pin: PD17
+spi_bus: usart1
+chain_position: 1
+chain_length: 6
+interpolate: False
+run_current: 1
+sense_resistor: 0.05
+
+[stepper_y]
+#driver 1
+step_pin: PC16
+dir_pin: PD10
+enable_pin: !PA9
+microsteps: 128
+rotation_distance: 40
+endstop_pin: PD15 #IO1
+position_endstop: 0
+position_max: 450
+
+[tmc5160 stepper_y]
+cs_pin: PD17
+chain_position: 2
+chain_length: 6
+interpolate: False
+run_current: 1.0
+sense_resistor: 0.05
+
+[stepper_z]
+#driver2
+step_pin: PC28
+dir_pin: PA4
+enable_pin: !PA9
+microsteps: 64
+rotation_distance: 8
+endstop_pin: PD28 #IO2
+position_endstop: 0
+position_min: 0
+position_max: 400
+
+[tmc5160 stepper_z]
+cs_pin: PD17
+chain_position: 3
+chain_length: 6
+interpolate: False
+run_current: 1.0
+sense_resistor: 0.05
+
+[adc_scaled vref_scaled]
+vref_pin: PC0
+vssa_pin: PC13
+
+[extruder]
+#driver3
+step_pin: PC1
+dir_pin: PA22
+enable_pin: !PA9
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA24 #Out1
+sensor_type: ATC Semitec 104GT-2
+pullup_resistor: 2200
+sensor_pin: vref_scaled:PC29 #Temp1
+control: pid
+pid_Kp: 30.089
+pid_Ki: 2.229
+pid_Kd: 101.550
+min_temp: 0
+max_temp: 285
+
+[tmc5160 extruder]
+cs_pin: PD17
+chain_position: 4
+chain_length: 6
+interpolate: False
+run_current: .6
+sense_resistor: 0.05
+
+[heater_fan heatbreak_fan]
+pin: PC8 #Out8
+heater: extruder
+heater_temp: 50.0
+
+[heater_bed]
+heater_pin: PA7 #Out0
+sensor_type: Generic 3950
+sensor_pin: vref_scaled:PC15 #Temp0
+control: pid
+pullup_resistor: 2200
+pid_Kp: 61.049
+pid_Ki: 2.339
+pid_Kd: 398.344
+min_temp: 0
+max_temp: 130
+
+[heater_fan heatbreak_fan]
+pin: PA15 #Out4
+
+[fan]
+pin: PC5 #Out5
+
+[mcu]
+serial: /dev/ttyACM0
+
+[printer]
+kinematics: cartesian
+max_velocity: 350
+max_accel: 3000