diff options
Diffstat (limited to 'config/example-extras.cfg')
| -rw-r--r-- | config/example-extras.cfg | 53 |
1 files changed, 43 insertions, 10 deletions
diff --git a/config/example-extras.cfg b/config/example-extras.cfg index 2a2e8ccf..8cf5649c 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -117,6 +117,26 @@ # using a probe to home the z-axis, it is recommended to define # a [homing_override] section in printer.cfg to home toward the # center of the print area. +# +# Visual Examples: +# bed_shape = rectangular, probe_count = 3,3: +# x---x---x (max_point) +# | +# x---x---x +# | +# (min_point) x---x---x +# +# bed_shape = round, probe_count = 5, radius = r: +# x (0,r) end +# / +# x---x---x +# \ +# (-r,0) x---x---x---x---x (r,0) +# \ +# x---x---x +# / +# x (0,-r) start +# #[bed_mesh] #speed: 50 # The speed (in mm/s) of non-probing moves during the @@ -130,21 +150,34 @@ #sample_retract_dist: 2.0 # The distance (in mm) to retract between each sample if # sampling more than once. Default is 2mm. +#bed_shape: rectangular +# Defines the shape of the bed for probing. May be 'rectangular', +# as is common for cartesian printers, or 'round', as is common for +# delta printers. Default is rectangular. +#radius: +# Defines the radius to probe when the bed_shape is 'round'. Note +# that the radius is relative to the nozzle's origin, if using a +# probe be sure to account for its offset. This parameter must be +# provided if the bed_shape is 'round'. #min_point: -# An X,Y point defining the minimum coordinate to probe on -# the bed. Note that this refers to the nozzle position, -# and take care that you do not define a point that will move -# the probe off of the bed. This parameter must be provided. +# Defines the minimum x,y position to probe when the bed_shape +# is 'rectangular'. Note that this refers to the nozzle position, +# take care that you do not define a point that will move the +# probe off of the bed. This parameter must be provided. #max_point: -# An X,Y point defining the maximum coordinate to probe on -# the bed. Follow the same precautions as listed in min_point. +# Defines the maximum x,y position to probe when the bed_shape +# is 'rectangular'. Follow the same precautions as listed in min_point. # Also note that this does not necessarily define the last point # probed, only the maximum coordinate. This parameter must be provided. #probe_count: 3,3 -# A comma separated pair of integer values (X,Y) defining the number -# of points to probe along each axis. A single value is also valid, -# in which case that value will be for both axes. Default is 3,3 -# which probes a 3x3 grid. +## OR ## +#probe_count: 5 +# For 'rectangular' beds, this is a comma separate pair of integer +# values (X,Y) defining the number of points to probe along each axis. +# A single value is also valid, in which case that value will be applied +# to both axes. 'Round' beds only accept a single integer value that is +# applied to both axes. The probe count must be odd for round beds. +# Default is 3,3 for 'rectangular' beds, and 5 for 'round' beds. #fade_start: 1.0 # The gcode z position in which to start phasing out z-adjustment # when fade is enabled. Default is 1.0. |