diff options
Diffstat (limited to 'config/example-extras.cfg')
| -rw-r--r-- | config/example-extras.cfg | 26 |
1 files changed, 13 insertions, 13 deletions
diff --git a/config/example-extras.cfg b/config/example-extras.cfg index 2d2ba7a0..c5a2712c 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -1090,7 +1090,7 @@ # provided. #chain_count: # The number of Neopixel chips that are "daisy chained" to the -# provided pin. The default is 1 (which indices only a single +# provided pin. The default is 1 (which indicates only a single # Neopixel is connected to the pin). #color_order_GRB: True # Set the pixel order to green, red, blue. If using the WS2811 chip @@ -1118,8 +1118,8 @@ #initial_BLUE: 0.0 # See the "neopixel" section for information on these parameters. -# Execute gcode when a button is pressed or released (or when a pin changes -# state). You can check the state of the button my using +# Execute gcode when a button is pressed or released (or when a pin +# changes state). You can check the state of the button by using # QUERY_BUTTON button=my_gcode_button #[gcode_button my_gcode_button] #pin: @@ -1158,8 +1158,8 @@ # is 0 (for low voltage). #cycle_time: 0.100 # The amount of time (in seconds) per PWM cycle. It is recommended -# this be 10 milliseconds or greater when using software based -# PWM. The default is 0.100 seconds for pwm pins. +# this be 10 milliseconds or greater when using software based PWM. +# The default is 0.100 seconds for pwm pins. #hardware_pwm: False # Enable this to use hardware PWM instead of software PWM. When # using hardware PWM the actual cycle time is constrained by the @@ -1576,8 +1576,8 @@ # The value to statically set the given MCP4451 "wiper" to. This is # typically set to a number between 0.0 and 1.0 with 1.0 being the # highest resistance and 0.0 being the lowest resistance. However, -# the range may be changed with the 'scale' parameter (see -# below). If a wiper is not specified then it is left unconfigured. +# the range may be changed with the 'scale' parameter (see below). +# If a wiper is not specified then it is left unconfigured. #scale: # This parameter can be used to alter how the 'wiper_x' parameters # are interpreted. If provided, then the 'wiper_x' parameters should @@ -1604,8 +1604,8 @@ #channel_d: # The value to statically set the given MCP4728 channel to. This is # typically set to a number between 0.0 and 1.0 with 1.0 being the -# highest voltage (2.048V) and 0.0 being the lowest voltage. However, -# the range may be changed with the 'scale' parameter (see +# highest voltage (2.048V) and 0.0 being the lowest voltage. +# However, the range may be changed with the 'scale' parameter (see # below). If a channel is not specified then it is left # unconfigured. #scale: @@ -1630,8 +1630,8 @@ # The value to statically set the given MCP4018 "wiper" to. This is # typically set to a number between 0.0 and 1.0 with 1.0 being the # highest resistance and 0.0 being the lowest resistance. However, -# the range may be changed with the 'scale' parameter (see -# below). This parameter must be provided. +# the range may be changed with the 'scale' parameter (see below). +# This parameter must be provided. #scale: # This parameter can be used to alter how the 'wiper' parameter is # interpreted. If provided, then the 'wiper' parameter should be @@ -1654,8 +1654,8 @@ # in "RepRapDiscount 2004 Smart Controller" type displays), "st7920" # (which is used in "RepRapDiscount 12864 Full Graphic Smart # Controller" type displays), "uc1701" (which is used in "MKS Mini -# 12864" type displays), "ssd1306", or "sh1106". This parameter must be -# provided. +# 12864" type displays), "ssd1306", or "sh1106". This parameter must +# be provided. #rs_pin: #e_pin: #d4_pin: |