diff options
Diffstat (limited to 'config/example-extras.cfg')
| -rw-r--r-- | config/example-extras.cfg | 55 |
1 files changed, 12 insertions, 43 deletions
diff --git a/config/example-extras.cfg b/config/example-extras.cfg index b0f8cdf3..2b0bdb1c 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -30,6 +30,15 @@ # triggers. This parameter must be provided. #speed: 5.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s. +#samples: 1 +# The number of times to probe each point. The probed z-values will +# be averaged. The default is to probe 1 time. +#sample_retract_dist: 2.0 +# The distance (in mm) to lift the toolhead between each sample (if +# sampling more than once). The default is 2mm. +#samples_result: average +# The calculation method when sampling more than once - either +# "median" or "average". The default is average. #activate_gcode: # A list of G-Code commands (one per line; subsequent lines # indented) to execute prior to each probe attempt. This may be @@ -72,6 +81,9 @@ #y_offset: #z_offset: #speed: +#samples: +#sample_retract_dist: +#samples_result: # See the "probe" section for information on these parameters. @@ -102,15 +114,6 @@ #horizontal_move_z: 5 # The height (in mm) that the head should be commanded to move to # just prior to starting a probe operation. The default is 5. -#samples: 1 -# The number of times to probe each point. The probed z-values -# will be averaged. The default is to probe 1 time. -#samples_result: average -# One can choose median or average between probes samples -# The default is average. -#sample_retract_dist: 2.0 -# The distance (in mm) to retract between each sample if -# sampling more than once. Default is 2mm. # Mesh Bed Leveling. One may define a [bed_mesh] config section @@ -147,15 +150,6 @@ #horizontal_move_z: 5 # The height (in mm) that the head should be commanded to move to # just prior to starting a probe operation. The default is 5. -#samples: 1 -# The number of times to probe each point. The probed z-values -# will be averaged. The default is to probe 1 time. -#samples_result: average -# One can choose median or average between probes samples -# The default is average. -#sample_retract_dist: 2.0 -# The distance (in mm) to retract between each sample if -# sampling more than once. Default is 2mm. #bed_radius: # Defines the radius to probe for round beds. Note that the radius # is relative to the nozzle's origin, if using a probe be sure to @@ -283,15 +277,6 @@ #horizontal_move_z: 5 # The height (in mm) that the head should be commanded to move to # just prior to starting a probe operation. The default is 5. -#samples: 1 -# The number of times to probe each point. The probed z-values -# will be averaged. The default is to probe 1 time. -#sample_retract_dist: 2.0 -# The distance (in mm) to retract between each sample if -# sampling more than once. Default is 2mm. -#samples_result: median -# One can choose median or average between screw probes -# The default is average. #screw_thread: CW-M3 # The type of screw used for bed level, M3, M4 or M5 and the # direction of the knob used to level the bed, clockwise decrease @@ -325,15 +310,6 @@ #horizontal_move_z: 5 # The height (in mm) that the head should be commanded to move to # just prior to starting a probe operation. The default is 5. -#samples: 1 -# The number of times to probe each point. The probed z-values -# will be averaged. The default is to probe 1 time. -#samples_result: average -# One can choose median or average between probes samples -# The default is average. -#sample_retract_dist: 2.0 -# The distance (in mm) to retract between each sample if -# sampling more than once. Default is 2mm. # Moving gantry leveling using 4 independently controlled Z motors. @@ -374,13 +350,6 @@ #max_adjust: 4 # Saftey limit if an ajustment greater than this value is requested # quad_gantry_level will abort. -#samples: 1 -# Number of probe samples per point. The defaut is 1 -#samples_result: average -# One can choose median or average between probes samples -# The default is average. -#sample_retract_dist: 2.0 -# Distance in mm to retract the probe between samples. Default is 2. # In a multi-extruder printer add an additional extruder section for |