diff options
| -rw-r--r-- | config/printer-lulzbot-taz6-2017.cfg | 66 |
1 files changed, 56 insertions, 10 deletions
diff --git a/config/printer-lulzbot-taz6-2017.cfg b/config/printer-lulzbot-taz6-2017.cfg index d045a004..80cc4bf2 100644 --- a/config/printer-lulzbot-taz6-2017.cfg +++ b/config/printer-lulzbot-taz6-2017.cfg @@ -2,6 +2,8 @@ # use this config, the firmware should be compiled for the AVR # atmega2560. +# For a TAZ6 with DualV3 extruder, see printer-lulzbot-taz6-dual-v3-2017.cfg. + # See the example.cfg file for a description of available parameters. [stepper_x] @@ -25,7 +27,6 @@ position_endstop: 306 position_min: -20 position_max: 306 homing_speed: 50 - [stepper_z] step_pin: PC2 dir_pin: PL2 @@ -37,6 +38,7 @@ position_min: -1.5 position_max: 270 homing_speed: 1 +# settings for "Tilapia" Hexagon extruder (TAZ6 standard) [extruder] step_pin: PC3 dir_pin: !PL6 @@ -55,19 +57,33 @@ min_temp: 0 max_temp: 300 min_extrude_temp: 140 -#[extruder1] -#step_pin: PC4 -#dir_pin: PL7 -#enable_pin: !PA3 -#heater_pin: PH4 -#sensor_pin: PF1 -#... +# settings for "Angelfish" Aerostruder (E3D Titan Aero V6) +#[extruder] +#step_pin: PC3 +#dir_pin: !PL6 +#enable_pin: !PA4 +#step_distance: 0.002381 +#nozzle_diameter: 0.400 +#filament_diameter: 2.920 +#heater_pin: PH6 +#sensor_type: ATC Semitec 104GT-2 +#sensor_pin: PF0 +#control: pid +#pid_Kp: 21.00 +#pid_Ki: 1.78 +#pid_Kd: 61.93 +#min_temp: 0 +#max_temp: 300 +#min_extrude_temp: 140 [heater_bed] heater_pin: PE5 -sensor_type: EPCOS 100K B57560G104F +sensor_type: Honeywell 100K 135-104LAG-J01 sensor_pin: PF2 -control: watermark +control: pid +pid_Kp: 162.0 +pid_Ki: 17.0 +pid_Kd: 378.0 min_temp: 0 max_temp: 130 @@ -114,3 +130,33 @@ lcd_type: st7920 cs_pin: PG4 sclk_pin: PJ2 sid_pin: PG3 +encoder_pins: ^PJ6,^PJ5 +click_pin: ^!PE2 +menu_timeout: 5 + +[probe] +pin: ^!PA0 +z_offset:1.377 +speed: 0.5 +lift_speed: 1.5 +samples: 2 +sample_retract_dist: 1.0 +samples_tolerance: 0.075 + +[bed_tilt] +points: -5,-3 + 290,-3 + 290,292 + -5,292 +speed: 75 +horizontal_move_z: 5 + +[safe_z_home] +home_xy_position: -19,265 +speed: 50.0 +z_hop: 10.0 + +# Perform ABL by running G29 in START gcode +[gcode_macro G29] +gcode: + BED_TILT_CALIBRATE |