diff options
| -rw-r--r-- | config/printer-creality-ender5-2019.cfg | 93 |
1 files changed, 93 insertions, 0 deletions
diff --git a/config/printer-creality-ender5-2019.cfg b/config/printer-creality-ender5-2019.cfg new file mode 100644 index 00000000..3e67bd07 --- /dev/null +++ b/config/printer-creality-ender5-2019.cfg @@ -0,0 +1,93 @@ +# This file contains common pin mappings for the 2019 Creality +# Ender 5. To use this config, the firmware should be compiled for the +# AVR atmega1284p. + +# Note, a number of Melzi boards are shipped with a bootloader that +# requires the following command to flash the board: +# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex +# If the above command does not work and "make flash" does not work +# then one may need to flash a bootloader to the board - see the +# Klipper docs/Bootloaders.md file for more information. + +# See the example.cfg file for a description of available parameters. + +[stepper_x] +step_pin: PD7 +dir_pin: PC5 +enable_pin: !PD6 +step_distance: .0125 +endstop_pin: ^PC2 +position_endstop: 0 +position_max: 235 +homing_speed: 30 + +[stepper_y] +step_pin: PC6 +dir_pin: PC7 +enable_pin: !PD6 +step_distance: .0125 +endstop_pin: ^PC3 +position_endstop: 0 +position_max: 235 +homing_speed: 30 + +[stepper_z] +step_pin: PB3 +dir_pin: !PB2 +enable_pin: !PA5 +step_distance: .0025 +endstop_pin: ^PC4 +position_endstop: 0.0 +position_max: 300 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB1 +dir_pin: !PB0 +enable_pin: !PD6 +step_distance: 0.010526 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PD5 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PA7 +control: pid +# tuned for stock hardware with 200 degree Celsius target +pid_Kp: 21.527 +pid_Ki: 1.063 +pid_Kd: 108.982 +min_temp: 0 +max_temp: 250 + +[heater_bed] +heater_pin: PD4 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PA6 +control: pid +# tuned for stock hardware with 50 degree Celsius target +pid_Kp: 54.027 +pid_Ki: 0.770 +pid_Kd: 948.182 +min_temp: 0 +max_temp: 130 + +[fan] +pin: PB4 + +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +[display] +lcd_type: st7920 +cs_pin: PA3 +sclk_pin: PA1 +sid_pin: PC1 +encoder_pins: ^PD2, ^PD3 +click_pin: ^!PC0 |