2 files changed, 127 insertions, 0 deletions
diff --git a/config/printer-artillery-genius-pro-2022.cfg b/config/printer-artillery-genius-pro-2022.cfg
new file mode 100644
index 00000000..aec7841c
--- /dev/null
+++ b/config/printer-artillery-genius-pro-2022.cfg
@@ -0,0 +1,126 @@
+# This file contains pin mappings for the Artillery Genius Pro (2022)
+# with a Artillery_Ruby-v1.2 board. To use this config, during "make menuconfig"
+# select the STM32F401 with "No bootloader" and USB (on PA11/PA12)
+# communication.
+
+# To flash this firmware, set the physical bridge between +3.3V and Boot0 PIN
+# on Artillery_Ruby mainboard. Then run the command:
+#   make flash FLASH_DEVICE=/dev/serial/by-id/usb-Klipper_stm32f401xc_*-if00
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[extruder]
+max_extrude_only_distance: 700.0
+step_pin: PA7
+dir_pin: PA6
+enable_pin: !PC4
+microsteps: 16
+rotation_distance: 7.1910
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PC9
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+min_temp: 0
+max_temp: 250
+control: pid
+pid_Kp: 23.223
+pid_Ki: 1.518
+pid_Kd: 88.826
+
+[stepper_x]
+step_pin: !PB14
+dir_pin: PB13
+enable_pin: !PB15
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA2
+position_endstop: 0
+position_max: 220
+homing_speed: 60
+
+[stepper_y]
+step_pin: PB10
+dir_pin: PB2
+enable_pin: !PB12
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA1
+position_endstop: 0
+position_max: 220
+homing_speed: 60
+
+[stepper_z]
+step_pin: PB0
+dir_pin: !PC5
+enable_pin: !PB1
+microsteps: 16
+rotation_distance: 8
+endstop_pin: probe:z_virtual_endstop
+position_max: 250
+position_min: -5
+
+[heater_bed]
+heater_pin: PA8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC1
+min_temp: 0
+max_temp: 130
+control: pid
+pid_Kp: 23.223
+pid_Ki: 1.518
+pid_Kd: 88.826
+
+[bed_screws]
+screw1: 38,45
+screw2: 180,45
+screw3: 180,180
+screw4: 38,180
+
+[fan]
+pin: PC8
+off_below: 0.1
+
+[heater_fan hotend_fan]
+pin: PC7
+heater: extruder
+heater_temp: 50.0
+
+[controller_fan stepper_fan]
+pin: PC6
+idle_timeout: 300
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_stm32f401xc_
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 4000
+max_z_velocity: 50
+square_corner_velocity: 5.0
+max_z_accel: 100
+
+[bltouch]
+sensor_pin: PC2
+control_pin: PC3
+x_offset:27.25
+y_offset:-12.8
+z_offset: 0.25
+speed:10
+samples:1
+samples_result:average
+
+[bed_mesh]
+speed: 800
+mesh_min: 30, 20
+mesh_max: 210, 200
+probe_count: 5,5
+algorithm: bicubic
+move_check_distance: 3.0
+
+[safe_z_home]
+home_xy_position: 110,110
+speed: 100
+z_hop: 10
+z_hop_speed: 5
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index e404f6f1..ba7adb61 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -204,6 +204,7 @@ CONFIG ../../config/printer-voxelab-aquila-2021.cfg
 # Printers using the stm32f401
 DICTIONARY stm32f401.dict
 CONFIG ../../config/generic-fysetc-cheetah-v2.0.cfg
+CONFIG ../../config/printer-artillery-genius-pro-2022.cfg
 CONFIG ../../config/printer-artillery-sidewinder-x2-2022.cfg
 CONFIG ../../config/printer-artillery-sidewinder-x3-plus-2024.cfg
 CONFIG ../../config/printer-creality-ender5-s1-2023.cfg