2 files changed, 100 insertions, 0 deletions
diff --git a/config/printer-creality-ender5plus-2019.cfg b/config/printer-creality-ender5plus-2019.cfg
new file mode 100644
index 00000000..c66c73d6
--- /dev/null
+++ b/config/printer-creality-ender5plus-2019.cfg
@@ -0,0 +1,99 @@
+# This file contains pin mappings for the Creality Ender 5 Plus.
+# Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro.
+# To use this config, the firmware should be compiled for the AVR
+# atmega2560.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PF0
+dir_pin: PF1
+enable_pin: !PD7
+step_distance: .0125
+endstop_pin: ^PE5
+position_endstop: 350
+position_max: 350
+homing_speed: 100
+
+[stepper_y]
+step_pin: PF6
+dir_pin: PF7
+enable_pin: !PF2
+step_distance: .0125
+endstop_pin: ^PJ1
+position_endstop: 350
+position_max: 350
+homing_speed: 100
+
+[stepper_z]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
+step_distance: .001266
+endstop_pin: probe:z_virtual_endstop
+position_max: 400
+position_min: 0
+homing_speed: 10.0
+
+[extruder]
+step_pin: PA4
+dir_pin: PA6
+enable_pin: !PA2
+step_distance: .010526
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 260
+
+[safe_z_home]
+home_xy_position: 180, 180
+speed: 100
+z_hop: 10
+z_hop_speed: 5
+
+[bltouch]
+sensor_pin: ^PD3
+control_pin: PB5
+x_offset: -45
+y_offset: 0
+z_offset: 0
+speed: 3.0
+pin_up_touch_mode_reports_triggered: False
+
+[bed_mesh]
+speed: 100
+horizontal_move_z: 8
+mesh_min: 50, 50
+mesh_max: 300,300
+probe_count: 3,3
+
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: pid
+pid_Kp: 690.34
+pid_Ki: 111.47
+pid_Kd: 1068.83
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PH6
+
+[mcu]
+serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 2500
+max_z_velocity: 5
+max_z_accel: 100
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index 5168ca9f..b8c5f441 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -28,6 +28,7 @@ CONFIG ../../config/printer-anycubic-kossel-plus-2017.cfg
 CONFIG ../../config/printer-creality-cr10s-2017.cfg
 CONFIG ../../config/printer-creality-cr20-2018.cfg
 CONFIG ../../config/printer-creality-cr20-pro-2019.cfg
+CONFIG ../../config/printer-creality-ender5plus-2019.cfg
 CONFIG ../../config/printer-lulzbot-mini1-2016.cfg
 CONFIG ../../config/printer-lulzbot-taz6-2017.cfg
 CONFIG ../../config/printer-lulzbot-taz6-dual-v3-2017.cfg