diff options
| -rw-r--r-- | config/generic-mellow-super-infinty-hv.cfg | 343 |
1 files changed, 343 insertions, 0 deletions
diff --git a/config/generic-mellow-super-infinty-hv.cfg b/config/generic-mellow-super-infinty-hv.cfg new file mode 100644 index 00000000..e35555df --- /dev/null +++ b/config/generic-mellow-super-infinty-hv.cfg @@ -0,0 +1,343 @@ +# This file contains common pin mappings for the 8 stepper motor "Mellow Super +# 8 HV Board" board. To use this config, the firmware should be compiled for +# the STM32F407 with a "32KiB bootloader". + +# The "make flash" command does not work on the Super 8 HV. Instead, after +# running "make", copy the generated "out/klipper.bin" file to a file named +# "firmware.bin" on an SD card and then restart the Super 8 HV with that SD card. + +# Serial options: +# * PA11/PA12 for serial over USB +# * PA9 /PA10 for serial UART +# * PD8 /PD9 for serial UART (to ESP32 module) + +# See docs/Config_Reference.md for a description of parameters. + +[stepper_x] +step_pin: PE2 # Drive0 +dir_pin: PC5 +enable_pin: !PF11 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG12 # IO0 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +[stepper_y] +step_pin: PE3 # Drive1 +dir_pin: PF13 +enable_pin: !PF14 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG11 # IO1 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +[stepper_z] +step_pin: PE4 # Drive2 +dir_pin: PG0 +enable_pin: !PG1 +microsteps: 16 +rotation_distance: 8 +endstop_pin: PG10 # IO2 +position_endstop: 0.5 +position_max: 200 + +[extruder] +step_pin: PE14 +dir_pin: PE8 +enable_pin: !PE9 +microsteps: 16 +rotation_distance: 33.500 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PC7 # Heat0 +sensor_pin: PF4 # ADC_0 +sensor_type: EPCOS 100K B57560G104F +control: pid +pid_Kp: 22.2 +pid_Ki: 1.08 +pid_Kd: 114 +min_temp: 0 +max_temp: 350 + +#[extruder1] +#step_pin: PE15 +#dir_pin: PE11 +#enable_pin: !PF2 +#heater_pin: PB1 # Heat1 +#sensor_pin: PF5 # ADC_1 +#... + +#[extruder2] +#step_pin: PE1 +#dir_pin: PF0 +#enable_pin: !PC15 +#heater_pin: PC7 # Heat2 +#sensor_pin: PF9 # ADC_2 +#... + +#[extruder3] +#step_pin: PE0 +#dir_pin: PG3 +#enable_pin: !PG4 +#heater_pin: PF7 # Heat3 +#sensor_pin: PF10 # ADC_3 +#... + +#[extruder4] +#step_pin: PE6 +#dir_pin: PG6 +#enable_pin: !PG7 +#heater_pin: PF6 # Heat4 +#sensor_pin: PC0 # ADC_4 +#... + +[heater_bed] +heater_pin: PE5 # BED +sensor_pin: PC1 # ADC_5 +sensor_type: ATC Semitec 104GT-2 +control: watermark +min_temp: 0 +max_temp: 200 + +# BLTouch port, has <GND>,<5V>,<CTRL>,<GND>,<PROBE> +#[bltouch] +#sensor_pin: ^PC3 +#control_pin: PC6 +#... + +# Accelerometer port, has <5V>,<GND>,<MISO>,<MOSI>,<INT>,<CS>,<SCLK> +#[adxl345] +#spi_speed: 5000 +#spi_software_miso_pin: PD0 +#spi_software_mosi_pin: PD1 +##interrupt: PD3 +#cs_pin: PD4 +#spi_software_sclk_pin: PD5 +#axes_map: x,y,z +#rate: 3200 + +[fan] +pin: PA0 # Fan0 + +[heater_fan fan1] +pin: PA1 + +#[heater_fan fan2] +#pin: PA2 + +#[heater_fan fan3] +#pin: PA3 + +#[heater_fan fan4] +#pin: PA15 + +#[heater_fan fan5] +#pin: PB11 + +#[heater_fan fan6] +#pin: PB10 + +#[heater_fan fan7] +#pin: PD12 + +#[heater_fan fan8] +#pin: PD14 + +#[heater_fan fan9] +#pin: PD15 + +[mcu] +serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00 + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +######################################## +# Stand-alone configuration +######################################## +# +# Jumpers A,B,C,D for stand-alone module is as follows: +# +# +-+-+-+-+ +# |A|B|C|D| B = MS3 +# |A|B|C|D| C = MS2 +# |.|.|.|.| D = MS1 +# +-+-+-+-+ + + +######################################## +# TMC2208 configuration +######################################## +# +# Jumper A for the stepStick module in UART mode is as follows: +# +# +-+-+-+-+ +# |.|.|.|.| +# |.|A|.|.| +# |.|A|.|.| +# +-+-+-+-+ + +#[tmc2208 stepper_x] +#uart_pin: PC4 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 stepper_y] +#uart_pin: PF12 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 stepper_z] +#uart_pin: PF15 +#run_current: 0.650 +#hold_current: 0.450 +#stealthchop_threshold: 999999 + +#[tmc2208 extruder] +#uart_pin: PE7 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 extruder1] +#uart_pin: PE10 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 extruder2] +#uart_pin: PF1 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 extruder3] +#uart_pin: PG2 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc2208 extruder4] +#uart_pin: PG5 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + + +######################################## +# TMC5160 configuration +######################################## +# +# Jumpers A,B,C,D for the stepStick module in SPI mode is as follows: +# +# +-+-+-+-+ +# |.|.|.|.| +# |A|B|C|D| +# |A|B|C|D| +# +-+-+-+-+ + +#[tmc5160 stepper_x] +#cs_pin: PC4 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PG12 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 stepper_y] +#cs_pin: PF12 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PG11 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 stepper_z] +#cs_pin: PF15 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PG10 +#run_current: 0.650 +#hold_current: 0.450 +#stealthchop_threshold: 999999 + +#[tmc5160 extruder] +#cs_pin: PE7 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PG9 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 extruder1] +#cs_pin: PE10 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PD7 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 extruder2] +#cs_pin: PF1 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PD6 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 extruder3] +#cs_pin: PG2 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PA8 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + +#[tmc5160 extruder4] +#cs_pin: PG5 +#spi_software_miso_pin: PB5 +#spi_software_mosi_pin: PB4 +#spi_software_sclk_pin: PB3 +##diag1_pin: PF3 +#run_current: 0.800 +#hold_current: 0.500 +#stealthchop_threshold: 999999 + + +######################################## +# EXP1 / EXP2 (display) pins +######################################## + +[board_pins] +aliases: + # EXP1 header + EXP1_1=PE12, EXP1_3=PB2, EXP1_5=PC14, EXP1_7=PG14, EXP1_9=<GND>, + EXP1_2=PE13, EXP1_4=PG8, EXP1_6=PC13, EXP1_8=PG13, EXP1_10=<5V>, + # EXP2 header + EXP2_1=PA6, EXP2_3=PB7, EXP2_5=PB6, EXP2_7=PG15, EXP2_9=<GND>, + EXP2_2=PA4, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=<RST>, EXP2_10=<5V> + +# See the sample-lcd.cfg file for definitions of common LCD displays. |