stm32: Use new CONFIG_USB to determine if USB needs to be configured

Introduce a CONFIG_USB build symbol that is set whenever
CONFIG_USBSERIAL or CONFIG_USBCANBUS is set.  Use that symbol during
setup so that the USB controller is properly initialized for both usb
serial and usb canbus bridge configurations.

This fixes the clock configuration for usb canbus bridge mode on
stm32f446.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

4 files changed, 9 insertions, 10 deletions

diff --git a/src/stm32/stm32f0.c b/src/stm32/stm32f0.c
index 98933b9d..e63f1b5b 100644
--- a/src/stm32/stm32f0.c
+++ b/src/stm32/stm32f0.c
@@ -86,7 +86,7 @@ pll_setup(void)
 
     // Setup CFGR3 register
     uint32_t cfgr3 = RCC_CFGR3_I2C1SW;
-#if CONFIG_USBSERIAL
+#if CONFIG_USB
         // Select PLL as source for USB clock
         cfgr3 |= RCC_CFGR3_USBSW;
 #endif
@@ -109,7 +109,7 @@ hsi48_setup(void)
         ;
 
     // Enable USB clock recovery
-    if (CONFIG_USBSERIAL) {
+    if (CONFIG_USB) {
         enable_pclock(CRS_BASE);
         CRS->CR |= CRS_CR_AUTOTRIMEN | CRS_CR_CEN;
     }
@@ -150,7 +150,7 @@ usb_reboot_for_dfu_bootloader(void)
 static void
 check_usb_dfu_bootloader(void)
 {
-    if (!CONFIG_USBSERIAL || !CONFIG_MACH_STM32F0x2
+    if (!CONFIG_USB || !CONFIG_MACH_STM32F0x2
         || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
         return;
     *(uint64_t*)USB_BOOT_FLAG_ADDR = 0;
@@ -204,8 +204,7 @@ armcm_main(void)
     FLASH->ACR = (1 << FLASH_ACR_LATENCY_Pos) | FLASH_ACR_PRFTBE;
 
     // Configure main clock
-    if (CONFIG_MACH_STM32F0x2 && CONFIG_STM32_CLOCK_REF_INTERNAL
-        && CONFIG_USBSERIAL)
+    if (CONFIG_MACH_STM32F0x2 && CONFIG_STM32_CLOCK_REF_INTERNAL && CONFIG_USB)
         hsi48_setup();
     else
         pll_setup();
diff --git a/src/stm32/stm32f4.c b/src/stm32/stm32f4.c
index 0b032de7..4f1dc084 100644
--- a/src/stm32/stm32f4.c
+++ b/src/stm32/stm32f4.c
@@ -139,7 +139,7 @@ enable_clock_stm32f446(void)
         ;
 
     // Enable 48Mhz USB clock
-    if (CONFIG_USBSERIAL) {
+    if (CONFIG_USB) {
         uint32_t ref = (CONFIG_STM32_CLOCK_REF_INTERNAL
                         ? 16000000 : CONFIG_CLOCK_REF_FREQ);
         uint32_t plls_base = 2000000, plls_freq = FREQ_USB * 4;
@@ -220,7 +220,7 @@ usb_reboot_for_dfu_bootloader(void)
 static void
 check_usb_dfu_bootloader(void)
 {
-    if (!CONFIG_USBSERIAL || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
+    if (!CONFIG_USB || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
         return;
     *(uint64_t*)USB_BOOT_FLAG_ADDR = 0;
     uint32_t *sysbase = (uint32_t*)0x1fff0000;
diff --git a/src/stm32/stm32g0.c b/src/stm32/stm32g0.c
index 36191ebf..63edcbaa 100644
--- a/src/stm32/stm32g0.c
+++ b/src/stm32/stm32g0.c
@@ -123,7 +123,7 @@ usb_reboot_for_dfu_bootloader(void)
 static void
 check_usb_dfu_bootloader(void)
 {
-    if (!CONFIG_USBSERIAL || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
+    if (!CONFIG_USB || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
         return;
     *(uint64_t*)USB_BOOT_FLAG_ADDR = 0;
     uint32_t *sysbase = (uint32_t*)0x1fff0000;
diff --git a/src/stm32/stm32h7.c b/src/stm32/stm32h7.c
index 565353dc..122ce64b 100644
--- a/src/stm32/stm32h7.c
+++ b/src/stm32/stm32h7.c
@@ -171,7 +171,7 @@ clock_setup(void)
         ;
 
     // Configure HSI48 clock for USB
-    if (CONFIG_USBSERIAL) {
+    if (CONFIG_USB) {
         SET_BIT(RCC->CR, RCC_CR_HSI48ON);
         while((RCC->CR & RCC_CR_HSI48RDY) == 0);
         SET_BIT(RCC->APB1HENR, RCC_APB1HENR_CRSEN);
@@ -205,7 +205,7 @@ usb_reboot_for_dfu_bootloader(void)
 static void
 check_usb_dfu_bootloader(void)
 {
-    if (!CONFIG_USBSERIAL || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
+    if (!CONFIG_USB || *(uint64_t*)USB_BOOT_FLAG_ADDR != USB_BOOT_FLAG)
         return;
     *(uint64_t*)USB_BOOT_FLAG_ADDR = 0;
     uint32_t *sysbase = (uint32_t*)0x1FF09800;