src: Rename source folders for atsam and atsamd architectures

Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>

1 files changed, 0 insertions, 61 deletions

diff --git a/src/samd21/serial.c b/src/samd21/serial.c
deleted file mode 100644
index 895ffb27..00000000
--- a/src/samd21/serial.c
+++ /dev/null
@@ -1,61 +0,0 @@
-// samd21 serial port
-//
-// Copyright (C) 2018  Kevin O'Connor <kevin@koconnor.net>
-//
-// This file may be distributed under the terms of the GNU GPLv3 license.
-
-#include "autoconf.h" // CONFIG_SERIAL_BAUD
-#include "board/serial_irq.h" // serial_rx_data
-#include "internal.h" // enable_pclock
-#include "samd21.h" // SERCOM0
-#include "sched.h" // DECL_INIT
-
-void
-serial_init(void)
-{
-    // Enable serial clock
-    enable_pclock(SERCOM0_GCLK_ID_CORE, PM_APBCMASK_SERCOM0);
-    // Enable pins
-    gpio_peripheral(GPIO('A', 10), 'C', 0);
-    gpio_peripheral(GPIO('A', 11), 'C', 0);
-    // Configure serial
-    SercomUsart *su = &SERCOM0->USART;
-    su->CTRLA.reg = 0;
-    uint32_t areg = (SERCOM_USART_CTRLA_MODE_USART_INT_CLK
-                     | SERCOM_USART_CTRLA_DORD
-                     | SERCOM_USART_CTRLA_SAMPR(1)
-                     | SERCOM_USART_CTRLA_TXPO(1)
-                     | SERCOM_USART_CTRLA_RXPO(3));
-    su->CTRLA.reg = areg;
-    su->CTRLB.reg = SERCOM_USART_CTRLB_TXEN | SERCOM_USART_CTRLB_RXEN;
-    uint32_t baud8 = CONFIG_CLOCK_FREQ / (2 * CONFIG_SERIAL_BAUD);
-    su->BAUD.reg = (SERCOM_USART_BAUD_FRAC_BAUD(baud8 / 8)
-                    | SERCOM_USART_BAUD_FRAC_FP(baud8 % 8));
-    NVIC_SetPriority(SERCOM0_IRQn, 0);
-    NVIC_EnableIRQ(SERCOM0_IRQn);
-    su->INTENSET.reg = SERCOM_USART_INTENSET_RXC;
-    su->CTRLA.reg = areg | SERCOM_USART_CTRLA_ENABLE;
-}
-DECL_INIT(serial_init);
-
-void __visible
-SERCOM0_Handler(void)
-{
-    uint32_t status = SERCOM0->USART.INTFLAG.reg;
-    if (status & SERCOM_USART_INTFLAG_RXC)
-        serial_rx_byte(SERCOM0->USART.DATA.reg);
-    if (status & SERCOM_USART_INTFLAG_DRE) {
-        uint8_t data;
-        int ret = serial_get_tx_byte(&data);
-        if (ret)
-            SERCOM0->USART.INTENCLR.reg = SERCOM_USART_INTENSET_DRE;
-        else
-            SERCOM0->USART.DATA.reg = data;
-    }
-}
-
-void
-serial_enable_tx_irq(void)
-{
-    SERCOM0->USART.INTENSET.reg = SERCOM_USART_INTENSET_DRE;
-}