config: Add example generic-bigtreetech-skr-2.cfg config (#4160)

Signed-off-by: Lars R. Hansen <popshansen@hotmail.com>

1 files changed, 142 insertions, 0 deletions

diff --git a/config/generic-bigtreetech-skr-2.cfg b/config/generic-bigtreetech-skr-2.cfg
new file mode 100644
index 00000000..fae82a15
--- /dev/null
+++ b/config/generic-bigtreetech-skr-2.cfg
@@ -0,0 +1,142 @@
+# This file contains common pin mappings for the BigTreeTech SKR 2.
+# To use this config, the firmware should be compiled for the
+# STM32F407 with a "32KiB bootloader".
+
+# The "make flash" command does not work on the SKR 2. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "firmware.bin" on an SD card and then restart the SKR 2
+# with that SD card.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PE2
+dir_pin: PE1
+enable_pin: !PE3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PC1
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: PD5
+dir_pin: !PD4
+enable_pin: !PD6
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PC3
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: PA15
+dir_pin: PA8
+enable_pin: !PD1
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PC0
+position_endstop: 0.5
+position_max: 200
+
+[extruder]
+step_pin: PD15
+dir_pin: PD14
+enable_pin: !PC7
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB3
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA2
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+#[extruder1]
+#step_pin: PD11
+#dir_pin: PD10
+#enable_pin: !PD13
+#heater_pin: PB4
+#sensor_pin: PA3
+#...
+
+[heater_bed]
+heater_pin: PD7
+sensor_type: NTC 100K beta 3950
+sensor_pin: PA1
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PB7
+
+#[heater_fan fan1]
+#pin: PB6
+
+#[heater_fan fan2]
+#pin: PB5
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PC5, EXP1_3=PB1, EXP1_5=PE10, EXP1_7=PE12, EXP1_9=<GND>,
+    EXP1_2=PB0, EXP1_4=PE9, EXP1_6=PE11, EXP1_8=PE13, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PA6, EXP2_3=PE7, EXP2_5=PB2, EXP2_7=PC4,  EXP2_9=<GND>,
+    EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=<RST>, EXP2_10=<NC>
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.
+
+########################################
+# TMC2209 configuration
+########################################
+
+#[tmc2209 stepper_x]
+#uart_pin: PE0
+#run_current: 0.800
+#hold_current: 0.800
+#diag_pin:
+
+#[tmc2209 stepper_y]
+#uart_pin: PD3
+#run_current: 0.800
+#hold_current: 0.800
+#diag_pin:
+
+#[tmc2209 stepper_z]
+#uart_pin: PD0
+#run_current: 0.800
+#hold_current: 0.800
+#diag_pin:
+
+#[tmc2209 extruder]
+#uart_pin: PC6
+#run_current: 0.600
+#diag_pin:
+
+#[tmc2209 extruder1]
+#uart_pin: PD12
+#run_current: 0.600
+#diag_pin: