config: Feature/add k8800 config (#4212)

Signed-off-by: Jelle Victoor <victoor.jelle@gmail.com>

1 files changed, 134 insertions, 0 deletions

diff --git a/config/printer-velleman-k8800-2017.cfg b/config/printer-velleman-k8800-2017.cfg
new file mode 100644
index 00000000..7fe79766
--- /dev/null
+++ b/config/printer-velleman-k8800-2017.cfg
@@ -0,0 +1,134 @@
+# This file contains common pin mappings for the Velleman K8800 printers (circa 2017).
+# To use this config, the firmware should be compiled for the AVR atmega2560.
+
+# See docs/Config_Reference.md for a description of parameters.
+# Arduino aliases for atmega2560/1280 (Arduino mega) boards
+[board_pins]
+aliases:
+    # Common EXP1 header found on many "all-in-one" ramps clones
+    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
+    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
+    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
+    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
+    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
+baud: 250000
+restart_method: arduino
+
+# X
+[stepper_a]
+step_pin: PF0
+dir_pin: PF1
+enable_pin: !PD7
+microsteps: 32
+rotation_distance: 55
+endstop_pin: ^!PE5
+homing_speed: 50
+position_endstop: 295
+arm_length: 207.0
+
+#Y
+[stepper_b]
+step_pin: PF6
+dir_pin: PF7
+enable_pin: !PF2
+microsteps: 32
+rotation_distance: 55
+endstop_pin: ^!PJ1
+
+#Z
+[stepper_c]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK1
+microsteps: 32
+rotation_distance: 55
+endstop_pin: ^!PK4
+
+[extruder]
+step_pin: PA4
+dir_pin: !PA6
+enable_pin: !PA2
+microsteps: 32
+rotation_distance: 42.4666
+nozzle_diameter: 0.3500
+filament_diameter: 1.750
+heater_pin: PB4
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PK5
+control: pid
+pid_Kp: 15.20
+pid_Ki: 1.75
+pid_Kd: 50.42
+min_temp: 0
+max_temp: 295
+
+
+
+[printer]
+kinematics: delta
+max_velocity: 250
+max_accel: 4000
+max_z_velocity: 250
+delta_radius: 100
+print_radius: 105.00
+minimum_z_position: -1
+
+[delta_calibrate]
+radius: 75
+
+[fan]
+pin: PH5
+
+[controller_fan default_controller_fan]
+pin: PH6
+
+[probe]
+pin: PK6
+speed: 12
+z_offset: -15
+
+[bed_mesh]
+speed: 120
+horizontal_move_z: 5
+mesh_radius:65
+mesh_origin: 0,0
+round_probe_count: 7
+algorithm: bicubic
+
+[display]
+lcd_type: uc1701
+contrast: 55
+cs_pin: PA7
+a0_pin: PA5
+encoder_pins: ^!PH1, ^!PH0
+# PR is open to enable this, without this, the encoder does not work
+#encoder_steps_per_detent: 2
+# encoder_fast_rate: 0.1
+click_pin: ^!PA1
+#kill_pin: ^!PD1
+
+[output_pin BEEPER]
+pin: PH3
+pwm: True
+value: 0
+shutdown_value: 0
+scale: 100
+
+[output_pin led]
+pin: PH4
+pwm: False
+
+[gcode_macro M300]
+default_parameter_S: 1000
+#   Use a default 1kHz tone if S is omitted.
+default_parameter_P: 100
+#   #   Use a 10ms duration is P is omitted.
+gcode:
+   SET_PIN PIN=BEEPER VALUE=50 CYCLE_TIME={ 1/S|float }
+   G4 P{P}
+   SET_PIN PIN=BEEPER VALUE=0