config: Add config for CR-10 Smart Pro, including installation instructions (#5396)

The pinout was found by windowpainting, initial config by Subwooferbone, tweaked by iblue.

Signed-off-by: Markus Fenske <iblue@gmx.net>

1 files changed, 161 insertions, 0 deletions

diff --git a/config/printer-creality-cr10-smart-pro-2022.cfg b/config/printer-creality-cr10-smart-pro-2022.cfg
new file mode 100644
index 00000000..e7127b24
--- /dev/null
+++ b/config/printer-creality-cr10-smart-pro-2022.cfg
@@ -0,0 +1,161 @@
+# This file contains pin mappings for the Creality CR-10 Smart Pro
+# with a CR-FDM-v2.5.S1 board.
+#
+# To use this config, during "make menuconfig" select the STM32F103
+# with a "64KiB bootloader" and serial (on USART1 PA10/PA9)
+# communication. Enable PA0 GPIO pin on startup.
+#
+# Flash this firmware on the MCU by copying "out/klipper.bin" to an SD
+# card and turning the printer on with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+#
+# The machine itself includes a small router that can run a Klipper
+# frontend. You don't need to buy a single-board computer.
+#
+# See docs/Config_Reference.md for a description of parameters.
+
+
+[stepper_x]
+step_pin: PB8
+dir_pin: !PB7
+enable_pin: !PC3
+rotation_distance: 40
+microsteps: 16
+endstop_pin: PC4
+position_min: -5
+position_endstop: -5
+position_max: 305
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB6
+dir_pin: PB5
+enable_pin: !PC3
+rotation_distance: 40
+microsteps: 16
+endstop_pin: PC5
+position_min: -2
+position_endstop: -2
+position_max: 302
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB4
+dir_pin: !PB3
+enable_pin: !PC3
+rotation_distance: 8
+microsteps: 16
+endstop_pin: probe:z_virtual_endstop
+position_min: -1.5
+position_max: 400
+homing_speed: 4
+second_homing_speed: 1
+homing_retract_dist: 2.0
+
+[extruder]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+rotation_distance: 7.640
+microsteps: 16
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB14
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PB1
+control: pid
+pid_Kp: 22.865
+pid_Ki: 1.292
+pid_Kd: 101.178
+min_temp: 0
+max_temp: 250
+
+[filament_switch_sensor runout_sensor]
+pause_on_runout: false
+runout_gcode: PAUSE
+insert_gcode: RESUME
+switch_pin: !PA15
+
+[heater_bed]
+heater_pin: PB13
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PB0
+control: pid
+pid_Kp: 72.49
+pid_Ki: 0.844
+pid_Kd: 1542.189
+min_temp: 0
+max_temp: 120
+
+[heater_fan hotend_fan]
+pin: PC13
+heater: extruder
+heater_temp: 50.0
+
+[fan]
+pin: PB15
+kick_start_time: 0.5
+
+[mcu]
+serial: /dev/ttyPrinter
+restart_method: command
+
+[temperature_sensor Board_MCU]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[bltouch]
+sensor_pin: ^PC15
+control_pin: PC14
+x_offset: -32.5
+y_offset: -40.6
+z_offset: 2.60 # initial safe value, get correct value by PROBE_CALIBRATE
+
+[safe_z_home]
+home_xy_position: 150,150
+speed: 50
+z_hop: 3
+z_hop_speed: 5
+
+[screws_tilt_adjust]
+screw1: 60, 80
+screw1_name: front left screw
+screw2: 300, 80
+screw2_name: front right screw
+# The rear screws are actually mechanically not reachable for the
+# probe, but that is ok, adjustments will still converge.
+screw3: 300, 300
+screw3_name: rear right screw
+screw4: 60, 300
+screw4_name: rear left screw
+horizontal_move_z: 10.
+speed: 50.
+screw_thread: CW-M3
+
+# Main light bar
+[output_pin lights]
+pin: PA7
+value: 1
+
+# Do not use PB12. PB12 resets the Wifi board.
+#[output_pin factory_reset]
+#pin: PB12
+#value: 0
+
+# Turns off the printer
+[output_pin power]
+pin: PA0
+value: 1
+shutdown_value: 1
+
+# Conservative default values that mimic the behaviour of the
+# stock firmware for easy results. It can go faster.
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 2000
+square_corner_velocity: 5.0
+max_z_velocity: 10
+max_z_accel: 100