config: Add config for printer Creality CR10s Pro V2 (#6300)

Created a base config for the Creality CR10s Pro v2 as described here: https://www.creality.com/products/cr-10s-pro-v2-3d-printer

This will allow users with this printer to more easily setup Klipper firmware.

Signed-off-by: Peter Kydas <peter@kydas.me>

1 files changed, 154 insertions, 0 deletions

diff --git a/config/printer-creality-cr10s-pro-v2-2020.cfg b/config/printer-creality-cr10s-pro-v2-2020.cfg
new file mode 100644
index 00000000..e06cd82c
--- /dev/null
+++ b/config/printer-creality-cr10s-pro-v2-2020.cfg
@@ -0,0 +1,154 @@
+# This file contains pin mappings for the Creality CR-10S Pro V2. To use
+# this config, the firmware should be compiled for the AVR atmega2560.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+## General Config
+[mcu]
+serial: /dev/serial/by-id/<YOUR_USB_ID>
+
+[printer]
+kinematics: cartesian
+max_velocity: 200
+max_accel: 1500
+max_z_velocity: 10
+max_z_accel: 100
+
+## Stepper Motors and Extruder
+[stepper_x]
+step_pin: PF0 #ar54
+dir_pin: PF1 #ar55
+enable_pin: !PD7 #!ar38
+rotation_distance: 40
+microsteps: 16
+full_steps_per_rotation: 200
+endstop_pin: ^PE5 #^ar3
+position_endstop: 0
+position_min: 0
+position_max: 300
+homing_speed: 50
+homing_retract_dist: 5
+
+[stepper_y]
+step_pin: PF6 #ar60
+dir_pin: !PF7 #ar61
+enable_pin: !PF2 #!ar56
+rotation_distance: 40
+microsteps: 16
+full_steps_per_rotation: 200
+endstop_pin: ^PJ1 #^ar14
+position_endstop: 0
+position_min: 0
+position_max: 310
+homing_speed: 50
+homing_retract_dist: 5
+
+[stepper_z]
+step_pin: PL3 #ar46
+dir_pin: !PL1 #!ar48
+enable_pin: !PK0 #!ar62
+rotation_distance: 8
+microsteps: 16
+full_steps_per_rotation: 200
+endstop_pin: probe:z_virtual_endstop
+position_min: -3
+position_max: 363 # you can go higher but then the cables crimp
+
+[extruder]
+step_pin: PA4 # ar26
+dir_pin: PA6 # !ar28
+enable_pin: !PA2 # !ar24
+rotation_distance: 22.900
+microsteps: 16
+full_steps_per_rotation: 200
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+max_extrude_only_distance: 500.0
+max_extrude_only_velocity: 70.0
+max_extrude_only_accel: 1000.0
+heater_pin: PB4 #ar10
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK5 #analog13
+control: pid #calibrated in Klipper, you will need to run this for your machine
+pid_kp: 28.359
+pid_ki: 1.616
+pid_kd: 124.426
+min_extrude_temp: 170
+min_temp: 5
+max_temp: 275
+
+[fan]
+pin: PH6 #ar9
+
+[heater_bed]
+heater_pin: PH5 #ar8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6 #analog14
+control: pid #calibrated in Klipper, you will need to run this for your machine
+pid_kp: 70.936
+pid_ki: 1.151
+pid_kd: 1093.298
+min_temp: 5
+max_temp: 140
+
+## BLTouch and Safe Z Settings
+[bltouch]
+sensor_pin: ^PD2
+control_pin: PB5
+stow_on_each_sample: False # Be careful
+probe_with_touch_mode: True
+x_offset: -27
+y_offset: -2
+z_offset: 2 # you will need to calibrate this in Klipper
+speed: 4.0
+samples: 2
+sample_retract_dist: 3.0
+
+[safe_z_home]
+home_xy_position: 177,155
+speed: 80.0
+z_hop: 10.0
+z_hop_speed: 5.0
+
+[bed_mesh]
+speed: 120
+horizontal_move_z: 5
+mesh_min: 5, 5
+mesh_max: 268, 305
+probe_count: 5,5
+fade_start: 1
+fade_end: 10
+
+[filament_switch_sensor e0_sensor]
+switch_pin: PE4 #ar2
+pause_on_runout: False
+runout_gcode:
+  PAUSE_PARK
+
+## Calibrating the Bed
+# this is for the bltouch to calibrate the bed
+[screws_tilt_adjust]
+screw1: 40,40
+screw1_name: front left screw
+screw2: 295,40
+screw2_name: front right screw
+screw3: 295,280
+screw3_name: rear right screw
+screw4: 40,280
+screw4_name: rear left screw
+speed: 50
+horizontal_move_z: 10
+screw_thread: CW-M3
+
+[bed_screws]
+screw1: 13,38
+screw1_name: front left screw
+screw2: 268,38
+screw2_name: front right screw
+screw3: 268,278
+screw3_name: rear right screw
+screw4: 13,38
+screw4_name: rear left screw
+horizontal_move_z: 5
+
+[pause_resume]