config: Integrate configuration file for Creality Sermoon V1. (#5621)

Configuration for the stock Creality Sermoon V1.

Signed-off-by: Du Chengyao <hbyls@live.com>

1 files changed, 108 insertions, 0 deletions

diff --git a/config/printer-creality-sermoonV1-2022.cfg b/config/printer-creality-sermoonV1-2022.cfg
new file mode 100644
index 00000000..ef100fb3
--- /dev/null
+++ b/config/printer-creality-sermoonV1-2022.cfg
@@ -0,0 +1,108 @@
+# This file contains pin mappings for the Creality Sermoon V1
+# with CR-FDM-v2.4.S1.200 motherboard.
+
+# To use this config, during "make menuconfig" select the STM32F401
+# with a "64KiB bootloader" and serial (on USB PA10/PA9) communication.
+
+# If you prefer a direct serial connection, in "make menuconfig"
+# select "Enable extra low-level configuration options" and select
+# Serial (on USART2 PA3/PA2), which is broken out on the 10 pin IDC
+# cable used for the LCD module as follows:
+# 3: Tx, 4: Rx, 9: GND, 10: VCC
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must changed to "firmware.bin"
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PA7
+dir_pin: !PA4
+enable_pin: !PB8
+microsteps: 16
+rotation_distance: 40
+endstop_pin: PC4
+position_endstop: 175
+position_max: 175
+position_min: 0
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB0
+dir_pin: PB10
+enable_pin: !PB8
+microsteps: 16
+rotation_distance: 40
+endstop_pin:  PB13
+position_endstop: 0
+position_max: 175
+position_min: 0
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB7
+dir_pin: PB6
+enable_pin: !PB8
+microsteps: 16
+rotation_distance: 8
+endstop_pin:  PB3
+position_endstop: 165
+position_max: 168
+position_min: -3
+
+[extruder]
+step_pin: PB1
+dir_pin: PB12
+enable_pin: !PB8
+microsteps: 16
+gear_ratio: 42:12
+rotation_distance: 26.359
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PC5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC1
+control: pid
+pid_Kp: 30.090
+pid_Ki: 1.875
+pid_Kd: 120.735
+min_temp: 0
+max_temp: 290
+
+[heater_bed]
+heater_pin: PB9
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+control: pid
+pid_Kp: 75.694
+pid_Ki: 1.160
+pid_Kd: 1234.759
+min_temp: 0
+max_temp: 90
+
+[fan]
+pin: PA5
+
+[fan_generic side_fan]
+pin: PC15
+
+# [controller_fan controller_fan]
+# In order to access the controller fan, the controller fan needs to be plugged
+# in another location. See https://github.com/Klipper3d/klipper/pull/5621
+# for more information.
+# pin: PB4
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 2000
+max_z_velocity: 5
+max_z_accel: 100
+
+[pause_resume]
+recover_velocity: 25