config: Add printer-tevo-flash-2018.cfg

Reported by @RadianceNL.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 118 insertions, 0 deletions

diff --git a/config/printer-tevo-flash-2018.cfg b/config/printer-tevo-flash-2018.cfg
new file mode 100644
index 00000000..761eb2da
--- /dev/null
+++ b/config/printer-tevo-flash-2018.cfg
@@ -0,0 +1,118 @@
+# Support for Tevo Flash using a Bondtech BMG extruder.  To use this
+# config, the firmware should be compiled for the AVR atmega2560.
+
+[stepper_x]
+step_pin: ar54
+dir_pin: !ar55
+enable_pin: !ar38
+step_distance: .012491
+endstop_pin: !ar3
+position_endstop: -13
+position_min: -13
+position_max: 235
+homing_speed: 50
+
+[stepper_y]
+step_pin: ar60
+dir_pin: ar61
+enable_pin: !ar56
+step_distance: .012441
+endstop_pin: !ar14
+position_endstop: -3
+position_min: -3
+position_max: 235
+homing_speed: 50
+
+[stepper_z]
+step_pin: ar46
+dir_pin: ar48
+enable_pin: !ar62
+step_distance: .002520
+position_max: 250
+endstop_pin: probe:z_virtual_endstop
+position_min: -2
+
+[stepper_z1]
+step_pin: ar36
+dir_pin: ar34
+enable_pin: !ar30
+step_distance: .002520
+
+[extruder]
+step_pin: ar26
+dir_pin: ar28
+enable_pin: !ar24
+step_distance: .002401
+nozzle_diameter: 0.600
+filament_diameter: 1.750
+heater_pin: ar10
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: analog13
+control: pid
+pid_Kp: 18.547
+pid_Ki: 0.788
+pid_Kd: 109.193
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: ar8
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: analog14
+control: pid
+pid_Kp: 38.824
+pid_Ki: 0.539
+pid_Kd: 698.838
+min_temp: 0
+max_temp: 70
+
+[heater_fan my_nozzle_fan]
+pin: ar7
+
+[fan]
+pin: ar9
+
+[mcu]
+serial: /dev/ttyUSB0
+pin_map: arduino
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 5
+max_z_accel: 100
+
+[display]
+lcd_type: uc1701
+cs_pin: ar25
+a0_pin: ar27
+encoder_pins: ^!ar31, ^!ar33
+click_pin: ^!ar35
+kill_pin: ar64
+
+[bltouch]
+sensor_pin: ar18
+control_pin: ar11
+x_offset: 0
+y_offset: 18
+z_offset: 1.64
+
+# The homing_override section modifies the default G28 behavior
+[homing_override]
+set_position_z: 0
+axes: z
+gcode:
+    G90
+    G1 Z5 F600
+    G28 X0 Y0
+    G1 X118 Y118 F3600
+    G28 Z0
+
+# Mesh Bed Leveling.
+[bed_mesh]
+samples: 3
+sample_retract_dist: 5
+min_point: 5,0
+max_point: 230,210
+probe_count: 9,9