diff options
| author | Kevin O'Connor <kevin@koconnor.net> | 2021-05-12 15:01:23 -0400 |
|---|---|---|
| committer | Kevin O'Connor <kevin@koconnor.net> | 2021-05-12 15:01:23 -0400 |
| commit | b4a2229788b49f76bad3a448cc1d0a4d2fc31695 (patch) | |
| tree | 0793feaf3592457b9c9f78516f1dd91f3d406ebf /config/printer-fokoos-odin5-f3-2021.cfg | |
| parent | 93add3a095c2f42846dc25054d0932588126386e (diff) | |
| download | kutter-b4a2229788b49f76bad3a448cc1d0a4d2fc31695.tar.gz kutter-b4a2229788b49f76bad3a448cc1d0a4d2fc31695.tar.xz kutter-b4a2229788b49f76bad3a448cc1d0a4d2fc31695.zip | |
config: Minor changes to printer-fokoos-odin5-f3-2021.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Diffstat (limited to 'config/printer-fokoos-odin5-f3-2021.cfg')
| -rw-r--r-- | config/printer-fokoos-odin5-f3-2021.cfg | 25 |
1 files changed, 11 insertions, 14 deletions
diff --git a/config/printer-fokoos-odin5-f3-2021.cfg b/config/printer-fokoos-odin5-f3-2021.cfg index 610be798..40c213d8 100644 --- a/config/printer-fokoos-odin5-f3-2021.cfg +++ b/config/printer-fokoos-odin5-f3-2021.cfg @@ -4,6 +4,17 @@ # permanently display "Booting..." after the Klipper firmware is flashed; use # Fluidd, Mainsail, or OctoPrint etc. to control the printer. +# To use this config, the firmware should be compiled for the STM32F103. When +# running "make menuconfig", enable "extra low-level configuration setup", +# select the 28KiB bootloader, and serial (on USART3 PB11/PB10) communication. +# Connect the printer to your Raspberry Pi using the printer's USB port. + +# Note that the "make flash" command does not work with MKS Robin +# boards. After running "make", run the following command: +# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin +# Copy the file out/Robin_nano35.bin to an SD card and then restart the +# printer with that SD card. The firmware will automatically be flashed. + # WARNING: The printer's Z endstop inductive sensor is not very accurate, so # stepper_z:position_endstop has been set to 0.0, for safety, below. This will # prevent the nozzle crashing into the bed when you first home Z. You must @@ -17,17 +28,6 @@ # This configuration does support the addition of a BLtouch. See below for # further instructions. -# To use this config, the firmware should be compiled for the STM32F103. When -# running "make menuconfig", enable "extra low-level configuration setup", -# select the 28KiB bootloader, and serial (on USART3 PB11/PB10) communication. -# Connect the printer to your Raspberry Pi using the printer's USB port. - -# Note that the "make flash" command does not work with MKS Robin -# boards. After running "make", run the following command: -# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin -# Copy the file out/Robin_nano35.bin to an SD card and then restart the -# printer with that SD card. The firmware will automatically be flashed. - # See docs/Config_Reference.md for a description of parameters. [mcu] @@ -130,9 +130,6 @@ pin: PB1 [filament_switch_sensor filament_sensor] switch_pin: !PA4 -# This is needed if you are using Arc Welder. -[gcode_arcs] - # BLtouch configuration. Uncomment these blocks if you have installed a # BLtouch. The correct wiring is to use the Robin Nano's BLtouch port for the # 3-wire connector (make sure you connect it the right way round) and the Z+ |