config: add support for creality sermoon D1 printer (#4621)

Signed-off-by: Shi Pan <twinkle-pirate@hotmail.com>

1 files changed, 127 insertions, 0 deletions

diff --git a/config/printer-creality-sermoonD1-2021.cfg b/config/printer-creality-sermoonD1-2021.cfg
new file mode 100644
index 00000000..08849814
--- /dev/null
+++ b/config/printer-creality-sermoonD1-2021.cfg
@@ -0,0 +1,127 @@
+# This file contains pin mappings for the Creality Sermoon D1 with
+# Rev. 4.3.1 Motherboard.
+
+# To use this config, during "make menuconfig" select the STM32F103
+# with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
+# communication.
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+rotation_distance: 40
+microsteps: 16
+endstop_pin: ^PA5
+position_min: -5
+position_endstop: -5
+position_max: 280
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+rotation_distance: 40
+microsteps: 16
+endstop_pin: ^PA6
+position_min: -2
+position_endstop: -2
+position_max: 260
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB6
+dir_pin: PB5
+enable_pin: !PC3
+rotation_distance: 8
+microsteps: 16
+position_endstop: 0.0                     # disable to use BLTouch
+endstop_pin: ^PA7                         # disable to use BLTouch
+# endstop_pin: probe:z_virtual_endstop    # enable to use BLTouch
+# position_min: -5                        # enable to use BLTouch
+position_max: 300
+homing_speed: 4
+second_homing_speed: 1
+homing_retract_dist: 2.0
+
+[extruder]
+max_extrude_only_distance: 1000.0
+step_pin: PB4
+dir_pin: PB3
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 34.936
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_kp: 26.163
+pid_ki: 1.418
+pid_kd: 120.675
+min_temp: 0
+max_temp: 260
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 76.301
+pid_Ki: 1.707
+pid_Kd: 852.669
+min_temp: 0
+max_temp: 100
+
+[fan]
+pin: PA0
+kick_start_time: 0.5
+
+[mcu]
+#use command ls /dev/serial/by-id/* to find the printer connected via USB
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+# Before printing the PROBE_CALIBRATE command needs to be issued
+# to run the probe calibration procedure, described at
+# docs/Probe_Calibrate.md, to find the correct z_offset.
+
+# [safe_z_home]                           # enable for BLTouch
+# home_xy_position: 150.7, 137
+# speed: 100
+# z_hop: 10
+# z_hop_speed: 5
+
+# [bltouch]
+# sensor_pin: ^PB1
+# control_pin: PB0
+# x_offset: 20
+# y_offset: 0
+# z_offset: 2
+# speed: 3.0
+
+# [bed_mesh]                              # enable for BLTouch
+# speed: 100
+# mesh_min: 20, 15
+# mesh_max: 250, 240
+# algorithm: bicubic
+# probe_count: 5,5
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: !PA4
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 500
+max_z_velocity: 5
+max_z_accel: 100